Display Mount Pro SSW 002 User manual

English
Installation Instruction
1
UNPACKING INSTRUCTIONS
! Carefully open the carton, remove contents and lay out on cardboard or other
protective surface to avoid damage.
! Check package contents against the Supplied Parts List in the next page to assure
that all components were received undamaged. Do not use damaged or defective
parts.
! Carefully read all instructions before attempting installation.
IMPORTANT SAFETY INFORMATION
! Install and operate this device with care. Please read this instruction before
installation, and carefully follow all instructions contained herein. Use proper safety
equipment during installation.
! Please call a qualified installation contractor for help if you don't understand these
directions or have any doubts about the safety of the installation.
Do not use this product for any purpose or in any configuration not explicitly specified
in this instruction. We hereby disclaims any and all liability for injury or damage
arising from incorrect assembly, incorrect mounting, or incorrect use of this product.

Supplied Par ts List
2
(5)M6x12 Bolt-p
(9)M4x6 Bolt-n
(3)Wire Cover-m (5)Axis Cover-o
(8)M4x12
Thumb Bolt-t
(8)M4x30 Bolt-u
(1)Allen Key-r(2)Stopper Ring-q
(1) Pole-a (1) “C” Clamp-b (1) “C” Clamp Brace-c (1) Grommet Base
Plate-d
(1)Support Plate-f(1)M10 Bolt-e (1)M10 Washer-g (1)Spring Washer-h
(3) VESA Plate with
Gas Spring Arm-k
(2)M10x15 Bolt-j (3)Add-on Arm-l(3) M5x14 Bolt-i
(8)M4 Space-v
(1) Keyboard Tray-A (1) Mouse Pad-C(1) Wrist Pad-B (4)M4 Nut-E(4)M4x10 Bolt-D
(1)Wrench-s
(3)Wire Clip-w (1)Arm Connector-x

Step 1 Install the Pole to the Desktop
Option A: Desk Clamp Install
1. Install the “C”-Clamp Brace(c) to the Pole
(a) using 3pcs M5x14 Bolts(i), see Figure 1.
2. Install the “C”-Clamp(b) to the pole
assembly according to the thickness of the
desktop. The thickness can be changed to
three positions. Connect it using 2pcs
M10x15 Bolts(j), and tighten using the Allen
Key(r). Tighten the “C”-Clamp to the desktop
using the metal knob, see Figure 2.
a
Figure 1
c
i
Option B: Grommet Base Install
If the existing grommet hole comes with a
plastic protector, remove it to ensure a flat
surface before installing the desk mount.
1. Install the Grommet Base Plate(d) to the
Pole(a) using 3pcs M5x14 Bolts(i), see
Figure 3.
2. Position the Pole(a) on the mounting
surface and secure using the Support Plate
(f), M10 Washer(g), Spring Washer(h) and
M10 Bolt(e). Fasten the M10 Bolt using
provided Wrench(s), see Figure 4.
a
Figure 3
d
i
Figure 4
f
e
g
h
Existing Grommet Hole Installation
Figure 2
j
r
b
Metal Knob
3

Step 1 Install the Pole to the Desktop
Self Drilled Grommet Hole Installation
Option B: Grommet Base Install
1. Position the Pole(a) on the mounting
surface and mark the center hole. Drill a 3/8"
(10mm) diameter hole at the marked position
through the mounting surface.
2. Install the Grommet Base Plate(d) to the
Pole(a) using 3pcs M5x14 Bolts(i), see
Figure 5.
3. Position the Pole(a) on the mounting
surface and secure using the Support Plate
(f), M10 Washer(g), Spring Washer(h) and
M10 Bolt(e). Fasten the M10 Bolt using
provided Wrench(s), see Figure 6.
a
Figure 5
d
i
Figure 6
f
e
g
h
4
Step 2 Connect the Gas Spring Arm(k) and Add-on Arm(l)
k
l
o
p
n
m
o
p
x

Step 3 Install Arms to the Pole
5
Step 4 Install the Keyboard/Mouse Tray to the Lower Arm
q
rq
r
w
D
E
A
B
C

Step 5
6
Step 6
Mount the Monitor to VESA Plate
For Flat Back Monitor For Curved Back Monitor
tu
v
Make Necessary Adjustments and Run Cables
Fix Tilt Angle

7
Thank you for choosing our products!
Step 7 Adjust the Torque of Gas Spring
Adjust the torque of gas spring according to the weight of your
monitor. If your monitor can not stay in the lower position, turn the
grub screw clockwise(-). If your monitor can not stay in the higher
position, turn the grub screw counterclockwise(+). Keep turning
until monitor position can be raised and lowered easily.
r