3IP2042EN 2012-07-24
AST panic devices are TÜV approved for use with DITEC TEN
and VA/O5model automations.
Each carriage installed must be connected to the mobile panic
wing b\at least two fastening points.
The wings to be used are intended as having been built with
DITEC PAM4/ and PAM4M series pro¿les.
The ma[imum height of the mobile panic wing (+M) must not
e[ceed 2400 mm.
The dimensions (/M) and the ma[imum weight of the door that
can be NnocNed out must compl\with the following graphs for
one and two mobile door automations.
Note: For dimensions and/or weights which are not accounted
Ior in the diagramcon¿rm the IeasiEiOit\oIthe SroMect with our
technicaOcommerciaOoI¿ces
600 8000
0
80
20
40
60
100
120
1000 1200
mm
1400 max
kg 1 wing automation
VALOR L - VALOR P - REX - TEN
VALOR B - VALOR N
MAX
MAX 100
120
AST
600 8000
0
80+80
20+20
40+40
60+60
100+100
120+120
1000 1200
mm
1400 max
kg
TEN
VALOR B - VALOR N
MAX
MAX
MAX
MAX REX
VALOR L - VALOR P
2 wings automation
90+90
70+70
70+70
90+90
100+100
120+120
If the width of the mobile panic wing (/M) is greater than 1000
mmadd reinforcement 417(see ¿g. 1)
If the width of the mobile panic wing (/M) is greater than 1200
mmadd reinforcement the third carriage.
If the weight of the mobile panic wing is greater than 0 Ngadd
Nit .AS4to the lower portion (see ref. 1 ¿g. 2).
Note: 2nO\ Ior 3$0/ ,I the weight oIthe door does not e[ceed
Nguse the .,F Nit in the Oower Sart see reI ¿g
The ma[imum height of the ¿[ed panic wing (+)) must not
e[ceed 2400 mm.
The width of the ¿[ed panic wing (/)) must not e[ceed 100
mm and the weight must not e[ceed 100 Ng.
REF. KIT Q.T.
AST1 Q.T.
AST2 SERIE
10KIT AST1 Q.T. PAM4/
1 KAS4AST2 SE5I-
ES
PAM4/
PAM4M
2--4---
7-2
KASM141 PAM4/
PAM4M
KASM24-1
10 KI)41 2 PAM4/
820
24
100
417
SPAZ4811
KASMG14
KASMN14 12
PAM4/
PAM4M
1-11-12-1-
14-1-1-
17-18-1-
20-21-22-
2-24-2
KAST1A4) 12
PAM4/
PAM4M
27 1CE/P522
PAM4/
PAM4M
Note: 8se .it &(/35 iI\ou wish to instaOO the ShotoceOOs that
detect the Sresence oISeoSOe and oEMects in the Sassage cham
Eer see reI Sag
$ttention: 8se the 3$0/ $67 or 3$00 $67 manuaOs
to determine the cut measurements, the kits required and
the required Sro¿Oe SreSarations
$ttention:
se the 3$0
/$
7or 3$0
0$
7manuaO
o determine the cut measurements, the kits required an
he required Sro
Oe SreSarations
i
