diversey Taski balimat 6500 User manual

1
2021-04-28
!1Instruction Manual EN(Translation of the Original Version)
___________________________________________________
balimat 6500
TMTM

2

3 CONTENTSThis operating manual contains instructions for using the sweeper. Carefully keep the operating manual so that you can refer to it later. Our products are being continuously improved. Design changes after going to print may therefore not be considered. If you have any questions, please contact our Service department (for contact details, see page 24). Carefully study the operating manual and the general safety instructions before you unpack the machine any further or undertake first start up. The operating manual is to be read attentively and followed by any person that operates the sweeper. CONTENTS CONTENTS, GENERAL ….3 CONTENTS ….3 PROPER USE ….4 EC CONFORMITY DECLARATION ….4 RATING PLATE ….4 EXPLANATION OF SYMBOLS ….4 CONSTRUCTION, FUNCTION, TECHNICAL DATA ….5 FUNCTION ….5 OPERATING AND FUNCTIONAL COMPONENTS ….6 TECHNICAL DATA ….7 SAFETY ….8 SAFETY INSTRUCTIONS (FOR OPERATION, BATTERIES) …8 SYMBOLS IN THE OPERATING MANUAL ….8 SAFETY INSTRUKTIONS-ATTACHEMENT STICKER ….9 SAFETY EQUIPMENT ….10 START UP ….10 WASTE DISPOSAL / RECYCLING ….10 OPERATION ….11 ADJUSTING THE DRIVER'S SEAT ….11 STARTING SWEEPER ….11 SWEEPING OPERATION ….12 SWEEPING OPERATION WITH SIDE BRUSHES, ROLLER BRUSH AND FAN ….12 SAFETY INSTRUCTIONS ….12 SWEEPING OPERATION ROLLER BRUSH ….12 STOPPING THE SWEEPING OPERATION ….12 SWEEPING OPERATION SIDE BRUSHES ….12 STOPPING THE SIDE BRUSHES ….12 OPERATING VACUUMING SYSTEM ….12 OPERATING THE FILTER SHAKER MECHANISM ….13 PARKING THE SWEEPER ….13 EMPTYING THE SWEEPINGS CONAINER ….14 REMOVING THE SWEEPINGS CONTAINER ….14 INSERTING THE SWEEPINGS CONTAINER ….14 REPLACING THE DUST FILTER ….15 INSERTING THE DUST FILTER ….15 INSTALLING THE FILTER ….15 CLEANING THE SWEEPER ….15 SIDE BRUSH ….16 REMOVING THE ROLLER BRUSH ….16 INSTALLING THE ROLLER BRUSH ….16 ADJUSTING THE SIDE BRUSH ….16 ROLLER BRUSH ….17 REMOVING THE ROLLER BRUSH ….17 INSERTING THE ROLLER BRUSH ….17 CHECK THE SWEEP ….18 SETTING THE SWEEP LEVEL ….18 BATTERIES ….19 CHARGING THE BATTERIES ….19 BRAKE ….20 ADJUSTING THE BRAKE ….20 BRAKE TEST ….21 AUTOMATIC SAFETY DEVICE ….21 STEERING ….22 TRANSPORT OF THE MACHINE ….22 TROUBLESHOOTING ….23 CONTACT DATA ….24 MAINTENANCE WORK / MAINTENANCE TABLE ….25 SHUT DOWN, DISMANTLING, DISPOSAL ….26 CIRCUIT DIAGRAM ….27

4Only use the sweeper according to the specifications in this operating manual. The sweeper is only intended for sweeping hard standing areas (e.g.: car parks, pavements, warehouses). The sweeping environment must not be wet. The sweeper must only be operated by reliable, instructed personnel. Prevent it from being used by children, young people and other unauthorised persons, e.g. by removing the key after use. Any other usage beyond this is deemed to be improper use (see “Safety Instructions”, page 7). The manufacturer is not liable for any damage resulting from this. The user is solely responsible for the risk. Proper use also includes following the operating manual, the safety instructions and keeping to the servicing and maintenance specifications. Only operate in expressly assigned routes and places. Observe the maximum climbing ability specified in the technical data and maximum possible slope inclination for operating across slopes. Due to an abrupt change of direction, particularly on slopes, the sweeper may tip. Adapt your operating manner and speed to the conditions. Follow the instructions on suitable ground (asphalt, screed, industrial floors, concrete, paving stones etc.)
PROPER USE
1.4 EG KONFORMITÄTSERKLÄRUNGEC DECLARATION OF CONFORMITYRATING PLATEThe rating plate is attached on the frame.EXPLANATION OF SYMBOLSDANGER! ......indicates a possibly dangerous situation that can cause death or serious injuries. CAUTION! ......indicates a possibly dangerous situation that can cause minor injuries. INSTRUCTION .....indicates important information.WARNING ...indicates a possibly dangerous situation that may cause material damage. Stolzenberg GmbH & Co. KGHamburger Str. 15-1749124 Georgsmarienhütte Germanywww.stolzenberg.deMade in GermanyMODEL: SERIAL NUMBER: PROTECTION: GVW:VOLTAGE: POWER: balimat 6500 XXXXXXX IPX3557 kg24 V1,25 kW
max. 2%
balimat 6500
Stolzenberg GmbH & Co. KGHamburger Str. 15-1749124 Georgsmarienhütte Germanywww.stolzenberg.deMade in GermanyMODEL: SERIAL NUMBER: PROTECTION: GVW:VOLTAGE: POWER:balimat 6500 XXXXXXX IPX3557 kg24 V1,25 kW
max. 2%
balimat 6500

5CONSTRUCTION, FUNCTION, TECHNICAL DATAadebcf
FUNCTION
The balimat 6500 is a battery-operated, ride-on vacuum sweeper vacuum sweeper fitted with the tandem roller system (TRS). The TRS allows large sweeping materials to be swept up without difficulty. The sweeper has a powerful vacuum function. In the tandem roller system (TRS), sweeping materials are first conveyed by means of the side brush (a) from the corners and edges of the sweeping area into the centre of the machine and therefore towards the two counter-rotating roller brush (b). From this, the sweeping material is taken up and conveyed into the dirt-hopper (c) situated at the back.The dust stirred up by the sweeping process is vacuumed up by a vacuuming system (fan) (d), filtered by flat-pleat filter (e) and thus separated from the clean air.Electro-mechanical filter cleaning (f) removes the dust caked onto the flat-pleat filter and allows this to drop into the dirt-hopper. * The version of the machine may differ from the illustration

6CONTROL PANELABCDEFGH
OPERATING AND FUNCTIONAL COMPONENTS OVERVIEW:
ISTQRLMNPOKJA.Side brush switchB.Main brush switchC.Vacuum/filter cleaner switchD.Battery condition displayE.Emergency stop switchF.Directional switchG.Horn push buttonH.Key switchI.Steering wheelJ.Front consoleK.Side brush lever (standard right)L.Side brush lever (optional left)M.Driver’s seatN.Main coverO.Debris hopperP.Drive wheelQ.Side coverR.Front trim panelS.Pivotable side brushesT.Front wheel with drum brake

7DIMENSIONS AND WEIGHTItemMeasureLength1420 mmWidth900 mmHeight at steering wheel1140 mmWeight: without batteries220 KgWeight: with batteries350 KgSweeping width without side brush700 mmSweeping width with oneside brush900 mmSweeping width with two side brush1100 mmDebris hopper volume90 ltrTurning Radius1210 mmClimbing capacityUp to 20%Speed0−6 km/hFilter Area4 qmAir volume of the Dust Filter900 m³/hSupporting framesSteel constructionpowder coatedTrim panel partsImpact resistantplasticHand-Arm-Vibration Kennwert2.5 m/s2ELEKTRIKFuseelectric circuitMeasureCB1Vacuuming System/Filter cleaning20CB2Roller brush25 ACB3Side brush10 A (20 A)CB4Horn, reverse signal,Warningbeacon20ACB5Traction drive45 AELEKTRIC DRIVESMotorMEASUREPropelling drivedifferential geared motor24V, 130 rpm, 400 WSide brushesgeared motor24V, 90 rpm, 90 WRoller brushgeared motor24V, 220 rpm, 400 WVacuuming SystemDC Motor, 24V, 3000 rpm, 300 WTIRESLocationTypeSizeFront (1)Solid260 x 85 mmBack (2)Pneumatic pressure (5,5 Bar)260 x 85 mmBRAKESBrakeLocationDrum brakeOn front wheelParking brakeOn front wheelTECHNICAL DATASound level maximum70 dB (A)CB7Charge Indicator/ Relais20 AFuseCb6Power supplyTraction drive electric1A

8SAFETY
Switching Driving Switching on
Switching Driving Switching on SAFETY INSTRUKTIONS SAFETY INSTRUCTIONS FOR OPERATION SAFETY INSTRUCTIONS ON BATTERIES As well as the operating manual and the binding regulations for accident prevention applicable in the country of usage and at the place where it is deployed, recognised rules for safety and expert working, and environmental protection, are also to be followed.• The machine is to be inspected before usage for its perfect condition and operational safety. If it is not in perfect condition, it must not be used.• In particular, have any errors that may affect safety rectified immediately.• Operating the machine in buildings at risk of explosion is prohibited.• Sweeping up of flammable, toxic or explosive materials and combustible gases or undiluted acids and solvents, burning or smouldering objects is prohibited.• The device is not suitable for accepting fluids, ropes, twines, wires or similar items.• Only use the machine with the dirt-hopper inserted to prevent injuries due to parts being projected.• Do not make any alterations or additions to the machine without the approval of the manufacturer.• Persons (including children) who, due to theirphysical, sensory or mental capacities or their inexperience or lack of knowledge, are not capable of using the machine safely must not use this machine without the supervision or instruction of a responsible person. Children must be supervised to ensure that they do not play with the machine.• Caution: Loose items of clothing may be drawn into rotating parts and cause serious or fatal injuries.• Transporting loads with the sweeper is not permitted.• Observe the maximum climbing ability specified in the technical data and maximum possible slope inclination for operating across slopes. The equipment may tip, particularly on slopes. Adapt your operating manner and speed to the conditions.• The machine is not permitted for use on roads.• Suitable, non-slip footwear is to be worn to avoid accidents.• The operating instructions of the battery manufacturer for their product and the specifications of the legislator on handling batteries are to be followed.• Charge flat batteries directly after usage and only keep in well-ventilated rooms.• Keep away from naked flames and electrical sparks in the charging area, as a highly-explosive gas mixture can be produced when charging batteries.• Always keep batteries clean and dry to avoid leakage currents. Never short circuit the battery terminals.SAFETY INSTRUCTIONS FOR CARE AND MAINTENANCE
WARNING! CAUTION! DANGER! THE INSTRUCTIONS DESCRIBED MUST BE FOLLOWED
WEAR BREATHING PROTECTION!
WEAR PROTECTIVE GOGGLES!
WEAR GLOVES!
SYMBOLS IN THE OPERATING MANUAL SYMBOLS ON THE SWEEPER
WARNING! CAUTION! DANGER! THE INSTRUCTIONS DESCRIBED MUST BE FOLLOWED!
FOLLOW THE OPERATING INSTRUCTIONS!
• To avoid damage to health, smoking, eating and drinking in the area of the battery charging station is to be avoided.• The battery must only be charged with the front panel open and secured by the cover holder.• Ensure safe and environmentally-friendly disposal of operating and auxiliary materials, as well as replacement parts, particularly batteries!• Before cleaning and maintaining the equipment,replacing parts or changing to a different function, the equipment is to be switched offand the ignition key is to be pulled out.• Spare parts must correspond to the requirements laid down by the manufacturer. This is always guaranteed for original spare parts.• Accessories and spare parts must only be installed by an authorised customer service department.• For work on the electrical system, the battery is to be disconnected.• The equipment must not be cleanedwith a hosepipe or high-pressure water jet (risk of short-circuits or other damage).• Repairs must only be made by the permitted customer service centres or by experts in this field familiar with all the relevant safety regulations.• Follow the safety review according to the locally-applicable regulations for mobile industrial equipment.• Always wear suitable gloves when working on the equipment.

9FLYINGDEBRISLABE:L --LOCATED ABOVE DRIVE AXLEThe following safety labels are mounted on the Machinein the locations indicated. If any Label becomes damaged or illegible, install a new label in ist place.FOR SAFETY LABEL − LOCATED ON THE SIDE OF THE OPERATOR COMPARTMENT.Battery charging lable-located in battery compartment SAFETY INSTRUKTIONS - ATTACHEMENT STICKER

10The Sweeper is ready for use. 1• Open the transport packaging and disengage the seat switch cable. 2• Remove the cover. Lift up hood at back and lift the front spigots of the hood out of the retainer. 3• Install the batteries (if not installed)4• Connect the batteries. Refer to technical data circuit diagram.5• Replace the hood panel.6. Connect the plugs of the seat switch cable.7. Install the side brush SAFETY EQUIPMENTSTART UP ! InstructionLook out for damage in transit and if there is any, indicate this to your specialist dealer without delay.GERÄTEHAUBE ÖFFEN4 .5WASTE DISPOSAL / RECYCLINGSEE ALSO: HES - Page 16INSTALLING THE SIDE BRUSSEE ALSO: PUTTING OUT OF OPERATION / RECYCLING - Page 26 WARNING! Use a unit ramp. The ramp must be designed in such a way as to allow the rear wheel as well as the drive wheels to travel across it. If this is not observed, damages to the sweeper mechanics may occur.If the drive pedal is activated during the starting procedure, the power supply to the driving motor is interrupted.Power supply to the electric motor is interrupted, if theDriver's seat is not weighed down; This sweeper can only be started if - the ignition key is set to the ON position; - the emergency switch is deactivated.If the main switch is set to reverse motion, an audible signal is heard. Recycling packaging materials. Do not dispose of packaging materials in normal waste but forward for reprocessing.For the disposal of all packaging materials, the disposal conditions specific for the location are applicable.

11BCA.Direktion SwitchB. Key switchC. Battery condition display 3. Insert the key into the key switch. 4.Turn the key clockwise5. Press the brake pedal.6. Release the parking brake.ABCAOPERATIONADJUSTING THE DRIVER`S SEATSTARTING SWEEPERLoosen the seat adjuster and shift the seat on the seat support to adjust the seat position.1• Sit down in the driver`s seatNOTE: The Sweeper cannot be driven if the driver's seatis not weighed down. 2• Check the position of the directional switch. NOTE:- Forward position: the machine is set to propel forward.- Backward position: the machine is set to propel in reverse.NOTE: A red LED starts flashing on the battery condition display indicating that the machine is ready for operation. After a few seconds the LED‘s will change to indicate the battery’s charging condition.NOTE: An audible signal will sound when backingthe machine.A. Parking brakeB. Brake pedalD. Accelerator pedal7. Press the accelerator pedal to adjust thespeed of the sweeper.

12DABCABCSWEEPING OPERATIONSAVETY INFORMATIONOPARATING THE SIDE BRUSH(ES) STOPPING THE SIDE BRUSH OPERATINGOPERATING THE VACUUMING SYSTEM (FAN) STOPPING THE ROLLER BRUSH OPERATING OF THE ROLLER BRUSHES Provide adequate ventilation when using the machine in closed rooms or buildings. Do not sweep hazardous materials. INSTRUKTION!The fan must absolutely be switched on. INSTRUKTION!Do not operate vacuuming system when debris is wet.This will cause damage to the fan.MUST BE FOLLOWED! You must only carry out the work described in this chapter if you have completely read and understood the operating manual, particularly page 8-11. INSTRUCTION Safety equipment is to be inspected for functioning before starting work. See alsoSafety, page 8INSTRUCTION Please adjust driving speed to the conditions (different ground surface, type and amount of sweeping material), to obtain a good sweeping result. INSTRUCTION When in operation, the dust filter must be cleaned at regular intervals and as required. INSTRUCTION When in operation, the dirt-hopper must be emptied at regular intervals and as required. S  - C D F, P 
S  - E D-H, P 
A. Side brush switchB. Main brush switchC. Vacuum/filter cleaner switchD. Main sweeping brush lever1. Start the sweeper.2. Place the main brush switch in the ON position. The indicator lamp on the switch lights up. The main brush begins rotating.3. Lower the main brush with the main brush lever.4. Sweep as required.1. Place the main brush switch in the OFF position.2. Raise the main brush with the main brush lever.1. Start the Sweeper.2. Place the side brush switch in the ON position. The indicator lamp on the switch lights up. The side brush(es) start(s) to rotate.3. Lower the side brush with the side brush lever.1. Place the side brush switch in the OFF position.2. Raise the side brush with the side brush lever.The vacuum prevents dust formation during sweeping operations1. Start the sweeper.2. Place the vacuum/filter cleaner switch in the top vacuum position.WARNING! The indicator lamp on the switch lights up. The vacuum begins operating.WARNING! Turn off the vacuum operation by placing the switch in the middle OFF position.A. Filter cleaner positionB. Vacuum positionC. Middle OFF position

13OPERATING THE FILTER CLEANING TURNING OF THE SWEEPER Instruction! Ensure that the dirt-hopper has been inserted. Instruction! It is recommended waiting 5-10 seconds until the fine dust has settled before emptying the dirt hopper. The flat-pleat filter collects fine dust during sweepingoperation. The filter cleaning cleans the dust andprevents the panel filter from being blocked bydebris.1. Place the main brush switch in the OFF position.2. Place the vacuum/filter cleaner switch in the middle OFF position.3. Wait until fan stops.4. Press and hold the switch in the filter cleaner position for about 5−10 seconds.1. Press and hold the brake pedal.2. Lock the brake by pulling the locking lever towards the driver’s seat.INSTRUKTION! When the brake is released the brake pedal must remain in pressed position.3. Switch off all functions.4. Raise the main brush and side brush(es) with the levers.5. Turn the key counterclockwise and remove it from the key switch.

14BACDEEMTYING THE DIRT-HOPPERREINSERTING THE DIRT-HOPPERREMOVING THE DIRT-HOPPER CAUTION! Risk of crushing when closing the dirt-hopper. DANGER! Brush throws debris. Stop motor before removing hopper.WARNING! At the back of the debris hopper two guiding rollers are installed to make the removal more easy. CAUTION! Risk of crushing when closing the dirt-hopperThe dirt container is where the debris is collected. It is positioned at the back of the sweeper. The dirt hopper must be emptied after each use.1. Turn the dirt-hopper locking devices upward.2. Pull the dirt-hopper from the sweeper by the handle until the front dirt-hopper guide rails are free. DANGER! Before leaving or servicing machine, stop on a level surface, set parking brake, turn off machine and remove key.A. Locking devicesB. HandleC. Guide rollerD. Guide railE. Dirt-hopper guides3. Lower the debris hopper to the ground.4. Remove the debris hopper completely from the sweeper.5. In order to empty the debris hopper use the free hand to take hold of the handle.6. The debris is discharged through the opening at the front of the hopper.7. Empty debris into appropriate containers only.8. Dump heavy loads on floor or use an assistant to help lift.1. Position the debris hopper in front of the sweeper opening.2. Align the debris hopper front guides level with guide rails.3. Slide the debris hopper into the sweeper.4. Turn the locking device downward.

15AAA. Star handlesACAB
REPLACING THE FLAT-PLEAT FILTER
POSITIONING THE FLAT-PLEAT FILTERINSTALLING THE FLAT-PLEAT FILTERCLEANING THE FILTER1. Open the hood.2. Lock hood securely using the hood prop.3. Loosen the top two star handles.4. Swing up the top angular bracket.5. Loosen the bottom two star handles.6. Pull the filter out of the fixture.Filter shows the following symbol on the frame.A. Filter sealMake sure the filter is facing the right direction when installing. The seal filter must show towards the filter housing as shown.The sweeper is equipped with electrical components.INSTRUCTION! Electronics controls of the machine are damaged by moisture. Moisture may lead to leak current and short circuits. Do not use high-pressure cleaning devices.1. Place the filter into the lower angular bracket.2. Swing the upper bracket over the filter.3. Tighten the top star handles slightly.4. Tighten star handles evenly crosswise so that the filter snugly fits all around the seal.5. Adjust the bolts and the nuts in a way that, provides the filter with the best possible Sealing inside the casing.A. Angular bracketsB. Star handleC. Filter

16ABCDEAASEITENBESENSIDE BRUSHESINSTALLING THE SIDE BRUSHADJUSTING THE SIDE BRUSHREMOVING THE SIDE BRUSH1. Fasten the flange plate to the side brush. The flange plate is equipped with a key. The side brush motor shaft is equipped with a keyway.2. Turn the side brush until the key fits snugly into the keyway.3. Slide the shim over the shaft of the side brush motor.4. Fasten the side brush to the shaft of the side brush motor with the fastening screw.FOR SAFETY: Before leaving or servicing machine, stop on a level surface, set parking brake, turn off machine and remove key.1. Turn off the sweeper.2. Raise the side brush with the side brush lever.3. Lift up the side brush motor.A. Side brush motorB. Side brush coverC. Shaft with keywayD. Flange base with feather keyE. Fastening screw4. Loosen the fastening screw at bottom center of the side brush.5. Pull the side brush down and off.6. Replace the side brush.Normal wear requires additional adjustment of the side brushes.1. Turn off the sweeper.2. Lower the side brush with the side brush lever.3. Loosen the bolts of the front panel.4. Remove the front panel.A. Bolts for the front panel5. Loosen the bolt of the side brush level adjustment.6. Move the side brush to the desired position.7. Tighten the bolt of the side brush level adjustment.A. Level adjustment bolt for side brush8. Reinstall the front panel.

17 − Turn off the sweeper. − Lower the main brush with the main brush lever. − Emergency stop button switch off the machine and pull out the ignition key to secure the machine against rolling away. − Pull lowering lever of the sweeping rollers. − Arrest the lowering lever. − Loosen the bolts of the left side cover.1. Fastening bolts of side trim panel − Remove the side panel.The roller swing is held in place by three star handles. − Loosen the star handles. − Remove the roller swing. − Pull the sweeping rollers out of the machine and remove any debris, cords, etc., from the roller tunnel and from the pick-up pins.− Push the sweeping rollers under the machine.Observe the sweeping rollers' sense of rotationwhile sliding them in.Each roller end is equipped with a keyway. Turn the sweeping roller until the pick-up pin of the rear roller swing fits into the keyway of the sweeping roller. Slide the sweeping rollers in as far as possible. Set the front roller swing onto the free sweeping roller ends. The roller swing is equipped with two turning levers. Each turning lever end is equipped with one pick-up pin.
1
Open star handle
2
Star handle with marking
3
Roller swing
4
Star handle
5
Turning lever
ROLLER BRUSH1Forward driveDirection of motion of the sweeping rollersREMOVING THE ROLLER BRUSHINSTALLING THE ROLLER BRUSH

18ACBKEHRWALZENSETTING ROLLER BRUSH CLEARANCEKEHRWALZENADJUSTING THE ROLLER BRUSH CLEARANCE − Turn the turning lever until the pick-up pin fits into the keyway of the sweeping rollers.− Push the roller swing over the threaded rods. − Make sure the sweeping rollers are fitted on both sides by the key-way into the pick-up pins and that all star handles are firmly tight-ened. − Fasten the side trim panel.
1
Threaded rods
2
Sweeping roller keyway
3
Pick-up pin
For best cleaning results and to ensure the highest possible device efficiency,the sweeping rollers are equipped with a sweeping contour.The sweeping contour should be set to approx. 40-50 mm at the rear roller brush.1. Drive the sweeper to an area to be cleaned.2. Turn the roller brushes on and lower it to the floor.3. Allow the roller brush to operate for about one or two minutes without moving.4. Lift the roller brushes.5. Stop roller brush operation and drive forward a few meters.6. The roller brush track visible on the ground is the roller brush clearance.ESTABLISHING ROLLER BRUSH CLEARANCEFOR SAFETY: Before leaving or servicing machine, stop on a level surface, set parking brake, turn off machine and remove key.1.Switch off the Sweeper.2. Lower the main brush.3. Tilt the main cover forward and prop it open.4. Adjust brush pattern with the forked lever or cam adjuster as needed.There are two ways to make adjustments to the main brush pattern.Fine adjustments can be made by moving the forked lever to a different hole. To move the forked lever, open the quick−release clip. Then the pin in the lever can be moved to the desired position. Close the clip when finished with the adjustment.Course adjustments can be made with the cam adjuster. Loosen the knob to make an adjustment. Tighten the knob when finished with the adjustment.A. Forked lever adjusterB. Quick−release clipC. Cam

19ABKEHRWALZENBATTERYKEHRWALZENCHARGING THE BATTERIES Charge the batteries before putting the INSTRUKTION! equipment into operation! INSTRUKTION! Charge the battery fully!
WARNING! CAUTION! DANGER! THEINSTRUKTIONS DESCRIBED MUST BE FOLLOWED!
FOLLOW THE INSTRUCTIONS ON THE BATTERY; IN THE USER INSTRUCTIONS FOR THE BATTERY AND OPERATING INSTRUCTIONS!
To do this, you must read the General Safety Instructions, particularly the Battery Warning Instructions (Page 7)!Please use original spare parts and contact Customer Services.RECOMMENDED BATTERIES 1. Turn of the sweeper2. Open the hood.3. Secure the hood position by the hood arresting device4. Guide the hood arresting into the holes at the bottom of the hood. (See Fig.1)5. Connect the plug of the charger to a power supply connector.6.The battery is fully charged if the light of the charger is lit green.7. Unplug the mains cable of the charging stationFour batteries supply the sweeper with electrical power. The charging condition of the batteries is indicated by the battery condition display on the control panel.Safety Instructions on BatteriesYou must note the following warning instructions for handling batteries.A. Battery−condition displayB. LED’sWhen the sweeper is switched on the red LED flashes five times. Subsequently the electronic system of the sweeper carries out a self−testing operation of the battery charging level. The result of this self−testing is displayed by the 5 LED‘s.Information provided by LED indicators on the battery condition display:
Red Yellow Green Green Green
condition fully chargedoperating/charging condition uncriticaloperating/only for a short time longeroperating/soon criticaloperating/criticalDANGERRisk of injury, the charger must only be put into operation if the mains cable is not damaged. A damaged mains cable is to be replaced without delay by the manufacturer, Customer Services or a qualified person. DANGERDanger of electric shock. Follow mains and use the correct fuse. Only user charger in dry rooms with sufficient (i.e. open front panel) ventilation. Observe charging times. DANGERRisk of injury! Follow the safety instructions when handling batteries. Follow usage instructions of the charger manufacturer.

20BCDFEAGBRAKEKEHRWALZENADJUSTING THE BRAKEThe brake (drum brake) acts on the front wheeland is controlled via the brake cable by the brakepedal.The brake adjustment is situated on the right sideof the front wheel facing in driving direction.FOR SAFETY: Before leaving or servicing machine, stop on a level surface, set parking brake, turn off machine and remove key.1. Hold the adjustment nut of the cable in place with a wrench.2. Loosen the back nut of the adjustment nut.3. Push the brake lever upward until the brake lever is fully engaged.4. Hold the brake lever in this position.5. Tighten the back nut of the adjustment nut.6. Now conduct a brake−test.The charging process lasts for approx. 10 hours when the batteries have been completely depleted (with the device originally provided by the manufacturer).The original charging device of the manufacturer can/should remain connected after charging is completed, because it is equipped with a charge saver allowing it to provide highest possible battery capacities even after long periods of standstill.Be careful only to use the sweeper if there is enough voltage left in the batteries. The machine automatically switches itself off, if the batteries are discharged to such a degree that damages may occur (excessive discharge protection).In this case: Switch off all functions and let the machine stand for about one or two minutes. Switch on the machine again and drive to the charging device (without sweeping operation!) Charge batteries immediately to avoid possible damages. CAUTION! RISK OF CRUSHING WHEN CLOSING THE FILTER BOX. ABCA. Sweeper connectorB. Battery connectorC. Charger connectorA. Wire guideB. Brake conduitC. Adjustment nutD. Back nutE. Brake cableF. Brake cable lockG. Brake lever(Fig. 1)