Dizmax Technology DOP2012F User manual

2. Removing the dome
3. Camera installation
:
:
Lift the dome. When you push the latch
button, it is unlocked and you ca n lift the dome.
(1) Fix the camera setwith the supplied screws on ceiling or wall mount.
If you d on't use supplied screws , the camera ma y fall off.
(2) Please refer to '4. Camera angle adjustment' regarding adjust
camera angle.
(3) Lens adjustment(Vari- focal Lens only)
①By turning the "Tele- Wide" knob,
you can acces s a ra nge of focal
lengths within specified limits.
②Since then, by turning the "Near- Far"
knob, you can set the focus toward
the wanted object.
(4) Re- as s emble the camera.
<Ce iling mount>
<Wall mount>
SC RE W TP13.5x20 2E A
SCR EW TP13.5x20 2EA
◐PRECAUTION
◐FE ATUR ES
◐HOW TO INSTALL
1. Do not install the camera outdoors.
2. Choose an ideal location for the camera, since a camera unit mus t
be protected against moisture and vibration.
3. Be careful notto scratc h the camera unit, especially lens or dome cover.
4. Use the camera within the temperature(- 10 ~ +50 ).
5. Handle with care. Dropping it can cause serious damage to the camera.
6. Avoid any direc t sun light toward the lens .
7. Use the AC adaptor 12V DC 300mA regulated.
1. This camera is incredibly flexible to install with its 3- axis camera con-
struction, which makes the c amera ceiling, wall or slope mountable.
2. Compact size dome cover(85 phi)
3. RS- 485 interface(Pelco- D, Pelco- P protocol support) - Option
4. Advanced High Resolution(700 T V- Line) - Option
5. Support 4 different privacy zone
6.DWDR(Digital Wide Dynamic Range)
7. Multi function : High Light Mask, Lens Shading Compensation, Impact
Detection(Option), Motion Detection
8. Multi- language full OSD support
: Pushing the latch button.
< >Remove the protection sheet after installing.
1. Opening the dome
Caution
P ROTE CTIO N S HEET
LATC H B UT TON
If the product is to be put out of operation definitively,
take it to a local recyc ling plant for a dis posal which
is not harmful to the e nvironment.
CAMERA HOLDER
LENS COVER
DISK
ROTATION
U
D
R
L
Ø 84Ø 110
Ø 85
BODY
DOME COVER
INNER DOME COVER
SC RE W
SC RE W
CABLE
DISK
BA SE
BOARD CA MER A AS S 'Y
C ONTR OL P CB
PUSH BUTTON
HARNESS
3- AXIS DOME CAMERA
MANUAL
4. Camera angle adjustment :
(1) Pan adjustment
(2) Tilt adjustment
(3) Roll adjustment
: Gras p the disk of camera and then adjust
direction to the right or left(- 180 ~ 180 )
: Grasp the lens cover of camera and then
adjust direction to the up or down(6 ~ 90 )
: Gras p the camera holder and then rotate
(- 178 ~ 178 )
˚ ˚
˚ ˚
˚ ˚
 DIMENSION
 ASSEMBLY
<Caution>If you try to adjust the camera out of limited angle, it might cause
trouble s and damage to c amera.
DOP2012F

2. How to use the jog lever
3. How to control through RS- 485 communication
4. Cable array o
①ENTER :
②UP, ③DOWN
④LEFT, ⑤RIGHT
⑥E X T- V IDEO
ㆍPush the lever : Used to acces s the menu and confirm selec tion.
ㆍPush the lever for one second : Used to return to previous menu
fromthe motion detection setting section or privacy mask setting
section.
: Used to move the cursor to up or down.
: Us ed to move the cursor to left or right a nd change
the value.
: E xtra video output terminal for insta llat
ion.
Plug your test monitor in hear. The cable is option.
ch the camera with controller's ID, baudrate and protocol
2) Up, Down, Left and right of Jog lever is same as Up, Down, Left
and right of R S- 485 controller
3) E nter of Jog lever is the same as menu key or IRIS open key of
RS - 485 c ontroller
4) Return to previous menu from motion detection setting section and
privacy mask setting section : Iris close or Iris open for a few second.
Or press the button as Up
1) No impact & motion alarm type
2) Built- in impact & motion alarm type
(option)
( ption)
1) Mat
 Right  Down  Left successively
E : ORANGE(RX +)
F : WHITE(RX - )
A : BLUE(MOTION)
B : BLACK(GND)
C : G RE E N( IMPACT)
D : B LACK(GND)
E : ORANGE(RX +)
F : WHITE(RX - )
MOTION ALARM
GND
IMPACT ALARM
GND
RX +
RX -
A
B
C
D
E
F
FUNCTION
ㆍIf the camera detected motion when using Motion & Impact
function, outside line of motion alarm connect with GND(B).
ㆍIf the camera detect impac t, outs ie line of impact alarm connect
with GND(D).Outputs of Motion & Impact are 'open collector'.
ㆍMax curre nt & volta ge are 200mA and 30V DC.
RS- 485A
RS- 485B
REMARK
No.
※All specification is subject to change withoutnotice to improve the quality.
NTSC / PAL
Internal
2:1 Interlac e
1.0 Vp- p(Sync . Negative) Termination 75Ω ± 10%
γ= 0.45(Adjustable)
0. 1 Lux(F /1.2)
Yes (Multi- language)
ON / OFF Selectable(64 Zone)
ON / OFF Selectable(3 Step : LOW / MIDDLE / HIGH)
ATW / AWC / MANUAL
ON / OFF Selectable(4 Zone)
PELCO- D&P
48dB over(AGC OFF)
ON / OFF
DWDR / BLC / HLC / OFF
YES
Sub control board with extra video c onnector
Automatic(Adjustable)
1/60~ 1
/10 0,00 0s e c(NTS C), 1/ 50~ 1/ 100 ,0 00sec (PAL)
Average test illuminance by front view
Regulated 12V DC ± 10%
- 10 ∼50℃
- 20 ∼60℃
Ø 85 × 80 (H)mm
Approx. 230g
Model No.
TV Type
Sync. Type
Scanning System
Video Output
Gamma Chara cteristic
Min. Illumination
OSD
Motion Detection
White Balace
Privacy Zone
Day & Night
RS- 485 Protocol
S/N Ratio
Mirror
Backlight
Control Interfac e
Gain Control
Shutter
Te st Illuminanc e Area
Current Consumption
Operation Temp.
Preservation Temp.
Dimens ion
Weight
Image Sensor
Power Supply
Max. 130mA(at 12V DC)
Vari- focal auto iris lens
or Fixed focal lens
Electronic D&N(AUTO, COLOR, B/W)
Reverse Polarity Protection
Imp act Detection(option)
1/ 3" SONY S UPER HAD C CDⅡ
Effective Pixel
Cell Size
Resolution
Lens
6.35㎛(H) X 7.4㎛(V)(NTSC),
6.5㎛(H) X 6.25㎛(V )(PAL)
768(H) X 494(V ) PIXEL(NTSC),
752(H) X 582(V) PIXEL(PAL)
COLOR : 700 TV- Line
B/W : 750 TV- Line
◐SPECIFICATION
AWB MODE
D&N MODE
LED LEVEL
DYNAMIC IR
MIRROR
SHARPNESS
GAMMA
LSC
R- Y GAIN
B- Y GAIN
MOTION
IMPACT
MASK
1, 2, 3, 4
CAM ID
BAUDRATE
PROTOCOL
LANGUAGE
BURST
DELAY TIME
LSC LEV EL
DISPLAY
SET
WINDOW
ALL SET↓
SENSITIVITY
HOLD TIME
HOLD TIME
EDIT
POSITION
Color temperature 2500 ~ 9500°K
Adjust the Red or B lue values to s hift the color
of the object
Move the camera lens toward to white paper
then press the s et button to find the optimal
white balance for current environment
Auto day&night switc hing mode
Fixed at color
Fixed at B/W
Determines whether to transmit the burst signal
or not in B /W mode
You can s elect brightness of illumination about
changing the day ↔night mode
You can s electthe duration time aboutc haining
the day ↔nightmode
N/A for W/O LED vers ion
N/A for W/O LED vers ion
S et a horizontal image inversion
Sharpness adjustable
Gamma adjustable
Determines whether to use the brightness com-
pensation of four lens' corners(LSC) or not
The LSC level selectable
Adjust Red tone of the image
Adjust Blue tone of the image
Determines whether to use the motion detection
function or not
No display on the screen though movement
is detected
The words 'MOTION' appear on the screen
when movement is detected
Motion detection area appear on the screen
when movement is detected
Motion detection s ensitivity
Set the duration of outs ide alarm. If the way of
display is message, it means display time of
message
Determines whether to use impact detec tion
func tion or not and sensitivity setting
Set the duration of outside alarm and display
time of "IMPACT" messa ge
Dis play each privacy mask or not. Press the
set button to move into the privac y mask
setting section, whenever you press the set
button, the mask color is changed. When the
mask color is red you can adjust the size by
up, down, left and right button. When the
mask color is blue you can set the position of
mask by up, down, leftand right button. Press
the set button for a few second to escape
S elect mask color
Select the camera ID for RS- 485 communi-
cation
S elect baud rate
S elect protocol
S elect language
Dis play the camera ID on the screen
ATW
MANUAL
AWC↓
AUTO
COLOR
B&W
OFF, ON
85 ~ 170
50 ~ 135
3 ~ 15
OFF, ON
OFF, ON
0 ~ 50
OFF, ON
0 ~ 50
0 ~ 200
0 ~ 200
OFF, ON
NONE
MESS AGE
MASK
0 ~ 255
1 ~ 15
OFF, LOW,
MIDDLE, HIGH
1 ~ 15
OFF, ON
1 ~ 255
2400 ~ 9600
ENGLISH, …
OFF, ON
6. PRIVACY
MASK
7. COMMUNI-
CATION
(option)
10. EXIT
9. FACTORY
SET
4. IMAGE
ADJUST
3. DAY&NIGHT
5. MOTION &
IMPACT
OFF, LOW, MIDDLE, HIGH
0.45, 0.6, 1, USER
PE LCO- D, PE LCO- P
MASK COLOR
NAME DISPLAY
BLACK, GRAY,…
8. SPECIAL
2. WHITE
BALANCE
ALLC LE AR↓
PATT ERN
GE NERATOR
COLOR B&W
B&W COLOR
→
→
Press the s et button to move into the motion detection area
section to setthe 64 areas. Press the set button for a few second
to move out
Press the s et button to s ele ct all area
Press the s et button to remove all area
Test signal. Press the set button, color bar appeared on the screen
and press any key to return to menu(SK- D385/M843, M863 only)
Press the set button to move into the position setting sec tion.
You can move the camera ID to your wanted position by using
up, down, left and right button
Press the set button to move into the name setting section. You
can choose the letter by using up and down button and move
next letter by using left and right button. P ress the set button for
a few second to move out
 If you change the COMMUNICATION value through RS- 485, you might not
control the camera due to unmatched value(If your c amera is out of working
due to above reason, change your controller's value or wait a few minute till
close the menu, it will be back to previous setting value)
To res et your camera to factory default condition
Notice : Lens, c ommunication and language is notchanged
Save the value and then restart
◐FUNCTION SETTING
1. OSD menu structure
Fixed focal lens or Vari- focal auto iris lens
In case of manual lens selection, adjust the
brightness
In case of DC lens selection, adjustthe bright-
ness
Shutter speed auto adjustable
S elect s hutter speed manually
Determines that use the AGC func tion or not
and AGC level s ele ctable(You c an not use the
Auto D&N change mode when AGC is off)
Digital Wide Dynamic Range
BLC function
High Light Mas k function
In case of AUTO mode, the func tion will off in
daytime and on at night
According to the threshold value, the camera
will recognize as High light or not.
LENS
E.SHUTTER
AGC
DWDR
BLC
HLC
BRIGHT
DC LEVEL
HLC THR
MANUAL, DC
0 ~ 100
0 ~ 20
AUTO
OFF, LOW,
MIDDLE, HIGH
OFF, ON
OFF, ON,
AUTO
0 ~ 100
1. E XPOSURE
1/60(1/50) ~ 1/100,000
Func tion
setting menu S elect menu ContentsSub menu
OFF, LOW, MIDDLE, HIGH
5
2
4
3
1
6
DOP2012F