dji INSPIRE 2 User manual

2017.01V1.0
User Guide
使用说明
INSPIRE 2
GPS Module for the Remote
Controller

2
© 2017 大疆创新 版权所有
免责声明
感谢您购买 DJITM 产品。本文所提及的内容关系到
您的安全以及合法权益与责任。使用本产品之前，
请仔细阅读本文以确保已对产品进行正确的设置。
不遵循和不按照本文的说明与警告来操作可能会给
您和周围的人带来伤害，损坏本产品或其它周围的
物品。本文档及本产品所有相关的文档最终解释权
归大疆 TM 创新（DJI）所有。如有更新，恕不另行
通知。请访问 www.dji.com 官方网站以获取最新的
产品信息。
一旦使用本产品，即视为您已经仔细阅读免责声明
与警告，理解、认可和接受本声明全部条款和内容。
您承诺对使用本产品以及可能带来的后果负全部责
任。您承诺仅出于正当目的使用本产品，并且同意
本条款以及大疆创新（DJI）制定的任何相关条例、
政策和指引。大疆创新（DJI）对于直接或间接使用
本产品而造成的损坏、伤害以及任何法律责任不予
负责。用户应遵循包括但不限于本文提及的所有安
全指引。
即使存在上述规定，消费者权益依然受当地法律法
规所保障，并不受本免责声明影响。
DJI 是深圳市大疆创新科技有限公司及其关联公司
的商标。本文出现的产品名称、品牌等，均为其所
属公司的商标或注册商标。
警 告
1. 请勿在强磁场或强电场区域使用或存放。
2. 请勿在阳光暴晒或靠近热源的区域使用。
3. 使用时避免任何液体溅洒到外接 GPS 模块上。
4. 使用时避免受到外力或物理撞击。

©2017 大疆创新 版权所有
3
简 介
使用 INSPIRETM 2 遥控器外接 GPS 模块，当激活“热
点跟随”功能时，坐标点更加精确，大幅提升飞行
器追随跟拍的准确性。同时，在飞行器飞行过程中，
随着遥控器的位置移动，遥控器的当前位置将会设
置成返航点，确保飞行器可安全飞回。
部件名称
1. 外接 GPS 模块主件
2. 固定贴带
3. CAN Bus 扩展接口
3
4
5
1
2
4. CAN 扩展模块
5. CAN Bus 插头
安 装
1. 将包装内的魔术贴分别粘贴于外接 GPS 模块主
件背面、CAN 扩展模块背面、遥控器移动设备支
架顶部及遥控器背面相应位置。

4
© 2017 大疆创新 版权所有
3. 用固定贴带将外接 GPS 模块主件与 CAN Bus 插
头的连接线固定于遥控器移动设备支架上，并将
连接线沿着遥控器一侧天线从外部绕过向下延展。
2
1
2. 固定外接 GPS 模块主件于遥控器移动设备支架
上端。

©2017 大疆创新 版权所有
5
4. 将CAN 扩展模块固定于遥控器底部，如图所示。
5. 将外接 GPS 模块一端的 CAN 接口插入遥控器
CAN Bus 接口。
3
4
6. 安装完毕如图所示。
• 安装过程中，切勿让连接线从遥控器天线
中间穿过，以免影响遥控器信号。
• 确保安装完毕后，外接 GPS 模块主件上
带DJI 标志面朝上，否则将会极大程度影
响外接 GPS 模块性能。
• 使用中切勿用金属材料覆盖外接 GPS 模
块。
• 插入遥控器 CAN Bus 接口时，注意插入
方向，切勿用力反插，以免损坏设备。
• 安装过程中，建议保持遥控器呈关闭状态，
避免带电插拔。

内容如有更新，恕不另行通知。
您可以在 DJI 官方网站查询最新版本
http://www.dji.com/inspire-2
INSPIRE 是大疆创新的商标。
Copyright © 2016 大疆创新 版权所有
• 固定外接 GPS 模块主件及 CAN 扩展模
块时，请用力按压，保证两端魔术贴已
粘贴牢固。
CAN Bus 扩展接口可用于外接其他设备，
如DJI Focus 跟焦器。
参 数
重量：33.9 g
卫星定位模块：GPS / GLONASS 双模
最大电流：125 mA
最大电压：5.3 V

© 2017 DJI All Rights Reserved.
7
Disclaimer
Congratulations on purchasing your new DJI™
product. The information in this document
affects your safety and your legal rights and
responsibilities. Read this entire document
carefully to ensure proper configuration before
use. Failure to read and follow instructions and
warnings in this document may result in serious
injury to yourself or others, damage to your DJI
product, or damage to other objects in the vicinity.
This document and all other collateral documents
are subject to change at the sole discretion of DJI.
By using this product, you hereby signify that you
have read this disclaimer and warning carefully
and that you understand and agree to abide by the
terms and conditions herein. You agree that you
are solely responsible for your own conduct while
using this product, and for any consequences
thereof.
You agree to use this product only for purposes
that are proper and in accordance with all
applicable laws, rules, and regulations, and
all terms, precautions, practices, policies and
guidelines DJI has made and may make available.
DJI accepts no liability for damage, injury or any
legal responsibility incurred directly or indirectly
from the use of this product. The user shall
observe safe and lawful practices including, but
not limited to, those set forth in this document.
Notwithstanding above, your statutory rights under
applicable national legislation are not affected by
this disclaimer.

8
© 2017 DJI All Rights Reserved.
DJI is a trademark of SZ DJI TECHNOLOGY CO.,
LTD. (abbreviated as “DJI”) and its affiliated
companies. Names of products, brands, etc.,
appearing in this document are trademarks or
registered trademarks of their respective owner
companies. This product and document are
copyrighted by DJI with all rights reserved. No part
of this product or document shall be reproduced
in any form without prior written consent of or
authorization from DJI.
Warnings
1. DO NOT place the INSPIRE™ 2 GPS Module
for the Remote Controller next to sources of
strong magnetic or electric fields.
2. Keep the Inspire 2 GPS Module for the Remote
Controller away from direct sunlight and other
heat sources.
3. Liquid spills may cause permanent damage
to the Inspire 2 GPS Module for the Remote
Controller.
4. DO NOT apply external pressure to the Inspire
2 GPS Module for the Remote Controller.
Introduction
If the Inspire 2 GPS Module for Remote Controller
is used, when Follow Me is activated, the aircraft
will automatically follow more precisely. The real-
time location of the remote controller will also
be recorded as the Home Point even when the
controller is moving, helping ensure a safe return
of the aircraft.

© 2017 DJI All Rights Reserved.
9
1. Master Part of the GPS Module
2. Velcro Strap
3. CAN Bus Port
Installation
1. Stick the provided Velcro tape on the back of
the Master part of the GPS module, the Can
Hub, the remote controller and the top of the
mobile device holder respectively.
Overview
3
4
5
1
2
4. CAN Hub
5. Cable End

10
© 2017 DJI All Rights Reserved.
2
4. Stick the CAN hub on the bottom of the remote
controller tightly as shown below.
5. Insert the cable end to the CAN Bus port on the
remote controller.
3. Fasten the cable and the mobile device holder,
and prevent it from dangling with the Velcro
strap. Ensure that the cable hangs down
beneath the remote controller alongside one
side of an antenna. DO NOT let the cable pass
through the middle of the antennas.
1
2. Mount the master part of the GPS Module on
the top of the mobile device holder with the
help of the already sticked-on Velcro.

© 2017 DJI All Rights Reserved.
11
3
4
6. Installation is complete.
• DO NOT let the cable pass through
the middle of the antennas, or it may
negatively affect the signal.
• The side marked with the DJI logo should
face out when the master part is properly
mounted.
• DO NOT cover the GPS Module with
metal.
• Ensure the cable is inserted correctly or the
CAN Bus port may be damaged.
• Always power off the remote controller
when mounting the GPS Module.
• Press hard when mounting the Master
part of the GPS module and the Can
Hub, or the Velcro may not be able to
tighten the GPS Module securely.

Other equipment can be connected to the
CAN Bus port on the CAN hub, e.g. DJI
Focus.
Specications
Weight: 33.9 g
Satellite Positioning System: GPS / GLONASS
Max. Current: 125 mA
Max. Voltage: 5.3 V
This content is subject to change.
Download the latest version from
http://www.dji.com/inspire-2
INSPIRE is a trademark of DJI.
Copyright © 2016 DJI All Rights Reserved.

Compliance Information
FCC Compliance
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) This device must accept any interference
received, including interference that may cause
undesired operation.
Any changes or modifications not expressly
approved by the party responsible for compliance
could void the user’s authority to operate the
equipment.
EU Compliance Statement: SZ DJI TECHNOLOGY
CO., LTD. hereby declares that this device is in
compliance with the essential requirements and
other relevant provisions of the EMC Directive.
A copy of the EU Declaration of Conformity is
available online at HYPERLINK "http://www.dji.com/
euro-compliance" www.dji.com/euro-compliance
EU contact address: DJI GmbH, Industrie Strasse.
12, 97618, Niederlauer, Germany

http://www.dji.com/support
技术支持
DJI Support
如果您对说明书有任何疑问或建议，请通过以下
电子邮箱联系我们：[email protected]。
中国印制
If you have any questions about this document,
please contact DJI by sending a message to
[email protected].
Printed in China.