DLS CRUISE CRPP-1.6 User manual
User manual
Citroën / Fiat / Peugeot
Declaration of conformity
Welcome to DLS!
Thank you for buying a DLS Cruise CRPP-1.6. For us, it’s all
about the sound experience. We care deeply about sound
and construction quality. In order for your experience to be
as optimal as possible, it is important that you fully read this
manual, preferably before you start your installation. Keep
the manual in a safe and accessible place for future
reference.
Your speakers must be installed correctly in order to work
as intended. Make sure you have all necessary tools nearby
before starting and that you are completely confident in how
to process. If you feel the slightest uncertainty; feel free to
take the help of an experienced installer or a car audio
dealer.
General
Some sound systems may vary in size of the door speaker.
Make sure that your vehicle has the same size as this kit,
before you start the assembly
This is a generic mounting instruction. The approach is
similar to all of the described car models. Some screws and
clips may be placed differently and depending, if the tweeter
is placed in the A-pillar or side mirror, the course of action
may vary.
DLS plug and play speakers for vehicles are manu-
factured in accordance with the EU directive EEC 95/54
(72/245/ EEC) and are marked with the approval
number. They are also marked in accordance with the
WEEE-directive 2012/19/EC. The products are also
produced in accordance with the EU RoHS directive
2015/863/EU.
Warranty
This component kit is covered by warranty, depending on
the conditions in the country where it is sold. If the speaker
is returned for service, please include the original dated
receipt with the product.
Winn Scandinavia AB
Elementvägen 15 - SE-702 27 Örebro - Sweden
www.dls.se
DLS speakers are engineered by DLS Sweden,
a part of:
Designed & Sound tuned in Sweden.
CRPP-1.6
DLS CRUISE
Content
Welcome
Pre installation
Dismounting door panel
Removing woofer
Changing woofer
Removing tweeter
Changing tweeter
Crossover
Running-in time
Technical assistance
Specification woofer
Specification tweeter
Compatible car models
Product markings
2
3
3
3
4
4
4
4
5
5
6
6-7
8
9
Installation
Pre installation
Disconnect Battery
Before you start the process
of replacing speakers,
disconnect and secure the
negative terminal from your
battery/power source. This
will prevent the risk of
damaging yourself or the
products.
Place the disconnected terminal in a secure and
isolated location away from any possible
connection belonging to the battery/power source
system.
Some sound systems may vary in size of the door
speaker. Make sure that your vehicle has the same
size as this kit, before you start the assembly
This is a generic mounting instruction. The
approach is similar to all of the described car
models. Some screws and clips may be placed
differently and depending, if the tweeter is placed
in the A-pillar or side mirror, the course of action
may vary.
General info
Included products:
2pcs Woofer
2pcs Tweeter
2pcs Crossover
Included in box:
2pcs Woofer
2pcs Tweeter
2pcs Crossover
2pcs Included bottom adapter
2pcs Flat-bottom adapter
2pcs Woofer connection line (for loose ends)
2pcs Tweeter connection line (for loose ends)
4pcs Adhesive foam with NC function
8pcs Terminal crimp connectors
4pcs Foam for wrapping
4pcs Screw
2pcs Adhesive for tweeter inclined adapter
8pcs Blind rivet
1pcs Rivet Tool
1pcs Manual
Unscrew the screws and store them in a safe
position, to re-use when re-mounting the door
panel.
Dismount the speaker grill by using the PRY tool.
Start the dismount
Tools that are needed
• Phillips screwdriver
• Screwdriver for slot screw. (ab 5mm)
• PRY tools (to avoid marks on the panels)
3
Place the new DLS Cruise driver in the hole for
the original speaker. Use the OEM screws to
safely mount the driver.
INFO: For those models that have different
mounting than described above, we have
included a rivet tool and 8 blind rivets.
Plug the speaker wire harness into the jack on the
new DLS speaker.
Mount the speaker grill by placing it over the
driver and softly giving it a push by the hand, so
that the grill snaps back in place.
Changing the tweeters
In most cases the tweeter is located behind the
A-pillar. Remove the A-pillar simply by pulling it
out. You can use PRY tools. In some cases you
may loosen the door rubber seal.
If the vehicle is equipped with a front curtain, you
have to loosen the screws at the top by the front
window.
When the A-pillar and top of the curtain is loosen,
be gentle when moving it.
Mounting the drivers Unscrew the old tweeter from the bracket and
un-plug the jack. Remove the OEM tweeter from
the bracket and replace it with the DLS tweeter.
The flat bottom adapter can also be used for the
assembly.
Use the four-leaf clover foam to secure the
tweeter on the back of the A-pillar. For some
models, the four-leaf clover needs to be adapted.
Use a sharp scissor to modify it.
Hint:
1) If there is no place for the tweeter behind the
A-pillar. The tweeter can be placed on the
dashboard, near the A-pillar (Use the included
bottom adapter). In this case, fix the tweeter with
double adhesive tape or hot glue. Just make sure
that the curtain has room to move freely
2) If there is a speaker location in the dashboard,
you can use the flat-bottom adapter to mount the
tweeter in the dashboard.
Connect the crossover with the PnP connector.
Use the other adhesive foam to secure the
crossover and cables.
The yellow cables are a jumper for decreasing
the tweeter level 4dB
4
Finally
Start assembling the covers again to finish the work. Make sure that no screws or clips are left over,
Reconnect the battery/power source terminal.
Finally, it´s time to play some good music and enjoy!
Running-in time
Allow the component kit to play for at least 15-20 hours in order to
perform at its possibly best. This run-in can be made with tone
sweep or with just music.
Start at a moderate volume and increase the volume step by step
during the running in period. After the 15-20 hour run in session the
performance and characteristics will be in the correct condition.
DLS Support
For technical assistance, ask your car audio dealer where the product was sold or the distributor in your country. You
can always contact the DLS Helpdesk in Sweden at e-mail: [email protected]. Information can also be found on our WEB-
site www.dls.se. We follow a policy of continuous advancement in development. For this reason, all or part of the
specifications and designs may be changed without prior notice.
5
Specifications
DLS DRIVE CRPP-1.6 Woofer
Technical Specifiaction
Size 6,5” /165 mm
RMS Power 100 W
MAX Power 200W
Voice Coil Size 1” /25mm
Voice Coil Material CCAW voice coil/ Kapton former
Basket Glass Fiber Reinforced ABS
Magnet Ferrite
Cone Glass Fiber
Suspension Rubber
Impedance 3 ohm
Freq. range 60Hz-5kHz
Electro-Acoustic Parameters
Re 2.99 Ohm
Fs 72.5 Hz
Mms 12.04 gr
Cms 0.401
Vas 10.86L
Qts 0.803
Qes 0.913
Qms 6.657
Bl 4.24 T.m
Spl 88.5 dB 1W/1M
Sd 139 cm²
38
18.7
21.5
31.2
Ø
Ø
Ø
158
Ø90
68.5
Woofer 6.5” /165 mm with glass fiber cone
Tweeter 1” / 25 mm silk dome tweeter with accessories
RMS Power 100 W
MAX Power 200W
Impedance 3 Ohm
Sensitivity 90dB 1W/1M
Freq. range 60Hz-25kHz
Crossover 4.8kHz 12dB/Oct with Mundorf caps
Attenuation Tweeter -4db/0db
DLS DRIVE CRPP-1.6 Tweeter
Technical Specifiaction:
Size 1” /2.54 mm
RMS Power 50 W
MAX Power 100W
Voice Coil Material CCAW voice coil/ Aluminium former
Frame Glass Fiber Reinforced ABS
Magnet Neodymium/Copper shorting ring
Cone Natural silk dome
Impedance 4 ohm
Freq. range 2000Hz-25kHz
Electro-Acoustic Parameters:
Re 3.5 Ohm
Fs 1993 Hz
SPL 94 dB 1W/1M
Art. no CK-CRPP-1.6
6
Impedance VS Frequency
Ø6.5
R86
7
DLS Cruise CRPP-1.6 compatible car models
Car Model Year Front kit Rear kit
Fiat Ducato 2006 – 2020 CRPP-1.6
Fiat Grande Punto 2005-2018 CRPP-1.6
Fiat 500 2007- CRPP-1.6
Fiat Panda 2012 – 2020 CRPP-1.6
Fiat Punto 2009 – 2018 CRPP-1.6
Fiat Tipo 2016 – 2020 CRPP-1.6
Ford Ka 2009 – 2016 CRPP-1.6
Citroën Jumper 2006 – 2021 CRPP-1.6
Citroen Relay 2006- CRPP-1.6
Dacia Dokker 2012 – 2018 CRPP-1.6 CRPP-1.6*
Dacia Lodgy 2012 – 2018 CRPP-1.6
Dacia Sandero 2012 – 2018 CRPP-1.6 CRPP-1.6*
Iveco Daily III 1999 – 2006 CRPP-1.6
Iveco Daily IV 2014 – 2021 CRPP-1.6
Nissan Almera 2000 – 2006 CRPP-1.6
Nissan Tiida 2007 – 2011 CRPP-1.6
Opel Tigra 1994 – 2001 CRPP-1.6
Opel Tigra Twin Top 2004 – 2009 CRPP-1.6
Peugeot Boxer 2006- CRPP-1.6
Vauxhall / Opel Astra H 2005 – 2010 CRPP-1.6
Vauxhall / Opel Corsa D 2006 – 2014 CRPP-1.6
Vauxhall / Opel Corsa E 2015 – 2019 CRPP-1.6
Vauxhall / Opel Meriva 2003 – 2010 CRPP-1.6
Vauxhall / Opel Omega 1994 – 2003 CRPP-1.6
Vauxhall / Opel Vectra 2002 – 2008 CRPP-1.6
Vauxhall / Opel Vivaro 2001 – 2014 CRPP-1.6
Vauxhall / Opel Zafira 1999 – 2005 CRPP-1.6
Vauxhall / Opel Vectra C 2002 – 2008 CRPP-1.6
*Disclaimer
For those models that have different mounting of the woofer than described above, we have included a rivet tool
and 8 blind rivets. Some tweeter mounting may be adjusted to fit your model. This guide have the woofer as
reference. Component system fits in rear doors, if there is a location for tweeter.
8
The crossed-out wheelie bin symbol means that the product, literature and pac-
kaging included must be taken to separate collection at the end of their working
life. Do not dispose of these products as unsorted municipal waste: take them
for recycling. For info on your nearest recycling point, check with your local
waste authority.
This product has been granted with the CE certification mark to show that the
product follows the health, safety, and environmental protection standards for
products sold within the European Economic Area (EEA).
DLS products complies with the relevant provisions of the RoHS
Directive for the European Union. In common with all Electrical
and Electronic Equipment (EEE) the productshould not be
disposed of as household waste. Alternative arrangements may
apply in other jurisdictions.
aideMeliboMnaeporuEehtforentraplabolgasiSLD
Association, an organisation that focus on promoting the
custom made mobile media installations to consumers.
Product markings
We follow a policy of continuous advancement in development. For this reason all or part of
specifications & designs may be changed without prior notice. We reserve for possible typos,
factual or numeric errors that may have been printed on any products, package designs,
user manuals and/or other included accessories.
9
Table of contents
Other DLS Speakers manuals
