DLS PA6.20 User manual

User manual

Content
Welcome
Warranty
General
Declaration of conformity
Included parts
Pre installation
Installation
Running-in time
DLS support
Wiring diagram
Specifications
Product markings
1
1
1
1
2
2
2
3
3
4
5
6
DECLARATION OF CONFORMITY
Welcome to DLS!
Thank you for buying a DLS Performance PA6.20. For us,
it’s all about the sound experience. We care deeply about
sound and construction quality. In order for your experience
to be as optimal as possible, it is important that you read
this manual, preferably before you start your installation.
Keep the manual in a safe and accessible place for future
reference.
Your speakers must be installed correctly in order to work
as intended. Make sure you have all necessary tools nearby
before starting and that you are completely confident in how
to process. If you feel the slightest uncertainty; feel free to
take the help of an experienced installer or a car audio
dealer.
General
Some sound systems may vary in size of the door speaker.
Make sure that your vehicle has the same size as this kit,
before you start the assembly
DLS plug and play speakers for vehicles are
manufactured in accordance with the EU directive
EEC 95/54 (72/245/ EEC) and are marked with
the approval number. They are also marked in
accordance with the WEEE-directive 2012/19/EC.
The products are also produced in accordance
with the EU RoHS directive 2015/863/EU.
Warranty
This component kit is covered by warranty, depending on
the conditions in the country where it is sold. If the speaker
is returned for service, please include the original dated
receipt with the product.
Winn Scandinavia AB
Elementvägen 15 - SE-702 27 Örebro - Sweden
Tel: [phone] - E-mail: [email protected]
www.dls.se
DLS speakers are engineered by DLS Sweden,
a part of:
Designed & Sound tuned in Sweden.
PA2.60
DLS PERFORMANCE

Included products:
2pcs Woofer
2pcs Tweeter
2pcs Crossover (including 2 x 50cm cable)
Included in box:
2pcs Tweeter bottom adapters
2pcs Tweeter cable 100cm (for loose ends)
2pcs Adhesive foam
8pcs V-type clips
8pcs Screws
2pcs Grills
1pcs Manual
Mount the speakers in the door or in the dashboard of your car. They may fit in the factory pre-made
mounting holes, if not you might have to modify the fitting. If you want to improve the sound reinforcement
you can use a baffle of MDF-board or similar. An installation high up on the door side is to be prefered. For
door placements, there are normally speaker rings that have to be used to make the speaker fit to the door
panel.
In many vehicles there are factory made places for tweeters that you can use for installation. If this is not
possible, try to install the tweeter close to the bass/midrange driver. The tweeter can also be installed on the
dash-board, or recessed in the door with the accessories included with the tweeters. NOTE! It is important
to fasten the speakers properly in order to avoid bad sound or rattling. Connect the speakers and crossovers
as in the drawing below.
Installation
2
Pre installation
Disconnect Battery
Before you start the process
of replacing speakers,
disconnect and secure the
negative terminal from your
battery/power source. This
will prevent the risk of
damaging yourself or the
products.
Place the disconnected terminal in a secure and
isolated location away from any possible
connection belonging to the battery/power source
system.
Included parts
- +
IN
TW
+
-
+
-
Installation of tweeter
The tweeter can be mounted on the dashboard with the included angled housing, or recessed in a door side.
Surface mounting
Put the cable through the hole in the rear end of the angled housing. The tweeter is attached to it by putting
them together and turn clockwise.Attach the housing to the surface with the included double adhesive tape.
Recessed mounting
You need a hole with a diameter of 43 mm/1.7”. Use glue to attach the recessed housing to the A-pillar, or door
panel. The tweeter is attached to the housing by putting the tweeter into it and turning clockwise.

3
Door insulation
DLS recommends using insulation/sound deadening
in the car doors.It lowers the noise from the road/tires
and prevent rattles and other noises from plastic
details in the doors.
If you need help deciding what type of door insulation
you should use, ask your DLS distributor for info and
guidance.
Allow the component kit to play for at least 15-20 hours in order to perform at its
possibly best. This run-in can be made with tone sweep or with just music.
Start at a moderate volume and increase the volume step by step during the
running in period. After the 15-20 hour run in session the performance and
characteristics will be in the correct condition.
Running-in time
For technical assistance, ask your car audio dealer where the product was sold or the distributor in your
country.You can always contact the DLS Helpdesk in Sweden at e-mail: [e-mail] Information can also
be found on our WEB-site www.dls.se We follow a policy of continuous advancement in development. For
this reason, all or part of specifications & designs may be changed without prior notice.
DLS support

4
Wiring diagram

Woofer 6.5” /165 mm with polypropylene cone
Tweeter 0,8” / 20 mm silk dome tweeter
RMS Power 60W
MAX Power 120W
PEAK Power 180W
Impedance 4 Ohm
Sensitivity 89dB 1W/1M
Freq. range 65Hz-20kHz
Crossover 5kHz 12dB/Oct
DLS PA6.20 Tweeter
Technical Specifiaction
Size 0,8” /20 mm
RMS Power 40W
MAX Power 80W
PEAK Power 120W
Frame Reinforced ABS
Magnet Neodymium
Cone Natural silk dome
Impedance 4 ohm
Freq. range 3000Hz-20kHz
DLS PA6.20 Woofer
Technical Specifiaction
Size 6,5” /165 mm
RMS Power 60W
MAX Power 120W
PEAK Power 180W
Basket Steel
Magnet Ferrite
Cone Polypropylene
Impedance 4 ohm
Freq. range 65Hz-5kHz
Specifications
Art. no PA6.20
17mm
Ø43mm
Ø53mm
Ø80mm
Ø166mm
58mm
5

The crossed-out wheelie bin symbol means that the product, literature and pac-
kaging included must be taken to separate collection at the end of their working
life. Do not dispose of these products as unsorted municipal waste: take them
for recycling. For info on your nearest recycling point, check with your local
waste authority.
This product has been granted with the CE certification mark to show that the
product follows the health, safety, and environmental protection standards for
products sold within the European Economic Area (EEA).
DLS products complies with the relevant provisions of the RoHS
Directive for the European Union. In common with all Electrical
and Electronic Equipment (EEE) the product should not be
disposed of as household waste. Alternative arrangements may
apply in other jurisdictions.
aideMeliboMnaeporuEehtforentraplabolgasiSLD
Association, an organisation that focus on promoting the
custom made mobile media installations to consumers.
Product markings
We follow a policy of continuous advancement in development. For this reason all or part of
specifications & designs may be changed without prior notice. We reserve for possible typos,
factual or numeric errors that may have been printed on any products, package designs,
user manuals and/or other included accessories.
6