DM Bath DMV2401 User manual

INSTALLATION GUIDE
MODELS DMV2401 / DMV3001 / DMV3601
DMV4801 / DMV6001 / DMV60DS / DMV72DS
24"
30"
36"
48"
60"
60"
72"
Getting Started 01
Required Tools & Materials 01
Vanity Installation 02
Drawer & Door Adjustment 03
Soft-Close Drawer Removal/Installation 03
Sink & Countertop Installation 04
Care & Maintenance 06
Limited Warranty 06
Technical Support 07

Getting Started
Required Tools & Materials
PLEASE READ CAREFULLY - IT IS RECOMMENDED THAT A QUALIFIED, LICENSED TRADES
PROFESSIONAL INSTALL YOUR UNIT.
All products must be inspected prior to installation. If damages are found due to transit or manufacturing defects then
DO NOT PROCEED WITH INSTALLATION and advise supplier immediately. Manufacturer will not be liable for any
installation, removal or re-installation costs. The warranty will be null and void if damage occurred during or after
installation.
When installing the vanity cabinets – the drawers and doors may need to be adjusted, due to movement during shipping.
Please view the instructions below on drawer and hinge adjustment.
Dezign Market accepts no liability for any damage to products or for any personal injury during installation.
Any wall to which product is fixed must properly support the weight of the vanity, sink and countertop. Secure to stud
framing or bracing (spanning the full length of the vanity) behind the finished wall. To ensure proper support and
alignment, the finished wall must be straight, the floor must be flat and perpendicular to the finished wall.
When moving the vanity, do not slide or side-load the legs, doing so WILL RISK DAMAGE TO THE VANITY.
Caution
Tape Measure Pencil Electric Drill Phillips Screwdriver Level 100% Silicone
Sealant
Ø12mm Screws
1

Determine the vanity placement and mark the area
on the wall where it will be installed. Check that the
wall is straight, not bowed or twisted. Ensure vanity
is square against the wall before securing. Door
and drawer alignment could be affected otherwise.
Adjust doors/drawers if required as they may have
moved during installation, refer to DRAWER &
DOOR ADJUSTMENT on page 3.
Vanity Cabinet Installation
01.
03. 04.
05. 06.
07. 08.
02.
60" single
Mark the location of the wall studs to which vanity
will be fastened. If the studs do not line up to the
mounting location for your vanity, wood bracing can
be installed between the studs using standard 2 x 4’s
behind the finished wall. This should be performed by
a qualified licensed trade professional.
DM Bath freestanding vanities have a solid back.
Mark and drill holes to accommodate drain and
supply pipes as necessary.
Place the vanity in desired installation location. Verify
that the vanity cabinet is level. If the vanity is not
level, use feet levelers to adjust as necessary.
Attach the vanity to the wall by screwing through
the back of the vanity cabinet into the wall studs.
Follow instructions for Sink & Countertop Installation
if using a DM BATH Sink & Countertop. If using a
custom top and sink, follow Manufacturers installation.
For DM BATH VESSEL SINK & COUNTERTOP
INSTALLATION, proceed to page 4.
For DM BATH UNDERMOUNT SINK & COUNTER-
TOP INSTALLATION, first proceed to page 4 for
COUNTERTOP INSTALLATION PRECAUTION then
proceed to page 5.
Choose the positioning of hardware of your choice
(not included) on the vanity cabinet. Mark the screw
hole location. Drill the cabinet with appropriate size
bit to accommodate the screw diameter. Install your
chosen hardware. Do not overtighten.
SIDE VIEW
60" single
60" single
WALL STUDS
MARK
SCREWS
2

Drawer & Door Adjustments
Soft-Close Drawer Removal & Installation
To make adjustments to doors or drawers please refer to the diagram below.
3

Countertop Installation Precaution
Vessel Sink & Countertop Installation
CAUTION - IMPORTANT HANDLING INSTRUCTION.
NEVER LIFT OR CARRY THE COUNTERTOP FLAT.
01. 02.
03. 04.
BEFORE INSTALLATION Examine and inspect the stone countertop and side/backsplash carefully ensuring no
defects. If defects are found, DO NOT PROCEED WITH INSTALLATION and inform your dealer immediately.
LIFTING COUNTERTOP - Professional 2-Person crew required who are capable of handling the weight of heavy stone
tops. You may require 3-Person crew for double vanity tops. Lift the countertop from the front edge, bringing to a vertical
position, while keeping the back edge in the box. IT IS IMPORTANT to support the countertop in a vertical position.
Support the countertop from the bottom and centre weight. Double vanity countertops may crack easily without proper
center support.
Soft-Close Drawer Removal & Installation
If you have a DM Bath Backsplash and/or Side
Splash, install next. Apply 100% Silicone Sealant
on the back of the backsplash/sidesplash. Vertically
align back/side splash making sure it is aligned to
countertop. Press into place.
Clean the surface of vessel cut-out on countertop.
Generously apply 100% Silicone Sealant around the
bottom of the vessel sink. Position sink under the
opening. Hold the sink in place. Immediately wipe
away any excess sealant.
Complete the faucet and drain installation according
to Manufacturer’s Installation guide.
Read lifting pre-caution above. Remove the
countertop from the box while maintaining its
vertical position. Lift countertop over cabinet base
carefully while still maintaining its vertical position.
Gently place the edge of top at the back of the
cabinet making sure aligned. Lower top to cabinet
make sure both ends come down at the same rate.
36" single
36" single
36" single
60" single
4

Undermount Sink & Countertop Installation
01. 02.
03. 04.
05. 06.
07.
Read lifting pre-caution above. Remove the
countertop from the box while maintaining its
vertical position. Carefully turn the counter top
over, resting it on a soft, stable surface to prevent
damage.
Position the undermount sink over the sink cutout on
the counter top. Make sure the sink is centered with
the faucet hole and is evenly spaced. Draw an outline
of the sink with pencil on the countertop.
Generously apply 100% silicone sealant around the
rim of the undermount sink.
Position and hold the sink at the opening ensuring
to follow your outline. Immediately wipe away any
excess sealant. Let dry for 24 hours.
Carefully turn the countertop and sink over. Place the
top on the vanity while maintaining a vertical position.
Gently place the edge of top at the back of the
cabinet making sure aligned. Lower top to cabinet
make sure both ends come down at the same rate.
60" single
60" single
60"
60" single
If you have a DM Bath back/side splash, install next.
Apply 100% silicone sealant on the backside.
Vertically align back/side splash making sure it is
aligned to countertop. Press into place. Immediately
wipe away excess sealant. Let dry for 24 hours.
Complete the faucet and drain installation according
to Manufacturer’s Installation guide.
5

To maintain the finish of your cabinet and countertop, use a clean soft cloth, lukewarm water and non-abrasive detergent.
To avoid deterioration it is important to keep surfaces dry of any moisture. Avoid exposure to chemicals, solvents, acids
and abrasive agents. Avoid contact with household chemical substances, such as toothpaste, mouthwash, lipstick, per-
fumes etc. Should your surface be exposed to any of these damaging products by accident, clean immediately with soft
cloth and lukewarm soapy water. Avoid use of highly aggressive cleaning agents, abrasive powder or cream. When using
professional cleaning products, follow the manufacturer’s instruction carefully and always test your cleaning solution on a
small-unexposed area before applying to the entire surface.
Cleaning Difficult Stains on Quartz Countertop
Avoid exposure to any strong chemicals and solvents on your quartz countertop. You should first try removing stain with:
For the purpose of spot cleaning difficult stains a solvent like acetone can be acceptable. It should ONLY be used for
short-term exposure at 50% dilution based on removing and rinsing applied area immediately after.
Care & Maintenance
Limited Warranty
DM Bath products (Bathroom vanities, mirrors, countertop, side/backsplash & sinks) carry a 2-year
limited warranty free from defects in material and workmanship for residential installations only.
This commences on the date of product shipment to the dealer or, if shipped direct, on the date of shipment to the
customer. If such a defect appears during the terms of this warranty, manufacturer will, at its own discretion repair, replace
the defective part(s) or the defective product, with the same or existing product of similar value, free of charge, excluding
installation and destination shipping costs.
• This warranty applies only to the original purchaser for the products that are subject to residential installation
only. This warranty is void if the product has been moved from its initial place of installation or has been used
for commercial, industrial or other non-residential use.
• Warranted item must have been purchased only from an authorized Dezign Market dealer, carrying DM BATH
products. A copy of the original purchase receipt is required for validation.
• Customer assumes responsibility for all merchandise recieved in original condition upon delivery.
• All defects must be reported as soon as possible, prior to install, not exceeding three (3) business days from
date of delivery. Failure to do so will result in denial of claim. No damage claims will be accepted after that.
• It is the customer’s responsibility to investigate all end user complaints regarding Dezign Market products. To
make a claim for a defective product, please have a digital photo taken of the defective product, please have a
digital photo taken of the defect and send it via email to [email protected] with detailed description.
• This warranty excludes the coverage of any costs incurred in the removal, re-installation and shipment of the
replacement product or the replacement parts, or any consequential damages.
• This warranty does not protect against malfunction or other failure caused by accidents, alterations, abuse,
neglect or misuse including, but not limited to: improper handling or storage conditions; damage during
installation; faulty maintenance, harsh detergents or abrasive cleaners; damage caused by fire, water, radical
temperature fluctuations or inadequate air circulation at the place of installation; repairs or modifications of any
kind, including painting, by persons not authorized by the manufacturer; or use for purposes other than intend-
ed or in locations subject to conditions not intended for the product(s).
• Normal wear and tear is not considered defect and not covered under warranty, including minor scratches or
chipped counters.
• This warranty does not apply to local building or plumbing code compliance. It is the consumer’s responsibility
to determine local code compliance prior to purchase and installation.
• This warranty is in lieu of all other warranties, expressed or implied, and the only one recognized by the manu-
facturer.
• To prolong the lifetime of DM BATH product(s), the recommended manufacturer’s installation and maintenance
procedures must be strictly followed.
• Dezign Market shall make the final determination on any issue or uncertainty regarding the application of this
warranty.
If the above limits and conditions are not met, the warranty will be null and void.
6
• A regular eraser.
• Mild liquid soap and water solution.
• A natural stone/quartz over-the-counter cleaning solution by buffing with a soft cloth or Mr. Clean magic eraser
sponge.

Technical Support
Our customer support department is available Monday - Friday 10:00 a.m. - 5:00 p.m. EST.
We can help with any questions you may have.
1 888 398 8380
[email protected]
DEZIGNMARKET.COM