DMP Electronics V-6012B Assembly instructions

INSTALLATION AND SETUP GUIDE
V-6012B and V-6014B
Fixed Bullet Camera

V-6012B/V-6014B Installation and Setup Guide | Digital Monitoring Products 1
GET STARTED
The V-6012B and V-6014B are indoor/outdoor video cameras that allows users to view live and recorded HD video
clips in Virtual Keypad™. The V-6012B records video in 2 Megapixels and the V-6014B records video in 4 Megapixels.
To activate the camera, you need an active Dealer Admin account at dealer.securecomwireless.com.
Compatibility
▶Any active Virtual Keypad account with Cameras & NVRs enabled
What’s Included
▶One V-6012B or V-6014B Camera with Mounting Plate
▶Mounting Template
▶Hardware Pack
▶One 32 GB SD Card
Procedure
This guide walks you through the required steps needed to install a V-6012B or a V-6014B camera. They are:
1. Wire the camera.
2. Mount the camera.
3. Activate the camera.
4. Configure motion detection regions or configure video analytics.

V-6012B/V-6014B Installation and Setup Guide | Digital Monitoring Products 2
WIRE THE CAMERA
Before connecting the Ethernet cable, install the waterproof Ethernet cable if desired. Refer to Figure 1.
Standard Power Connection
Connect a 12 VDC power supply (not included) to the camera power connector. Connect a network cable to the
camera Ethernet connector.
PoE Connection
Connect a network cable to the camera Ethernet connector. Connect the cable to a PoE switch or injector.
Figure 1: Installing the Waterproof Ethernet Cap
1/4
Turn
Turn
until
tight
Wire
and
crimp,
then
plug in
to camera
Ethernet
connector
Seat
o-Ring
between
cover and
Ethernet
connector,
then slip
cover over
connector
O-Ring
Cover
End Cap
From router/switch

V-6012B/V-6014B Installation and Setup Guide | Digital Monitoring Products 3
MOUNT THE CAMERA
Standard Wall or Ceiling Mount
Refer to Figure 2 when mounting the camera.
1. Place the mounting template at the location you want to mount the camera.
2. Drill holes into the mounting template.
3. Turn the adjustment knob counterclockwise to loosen the camera.
4. Use the included screws and wall anchors to mount the camera base to a wall or ceiling.
5. Turn the adjustment knob clockwise to tighten the camera.
Note: The mounting surface must be capable of holding five times the camera’s weight.
Adjust the Camera
Refer to Figure 3 when adjusting the camera.
1. Turn the adjustment knob counterclockwise to loosen the camera.
2. Adjust the pan, tilt, and camera rotation angle as needed.
3. Turn the adjustment knob clockwise to tighten the camera.
Pan
0° ~ 360°
Tilt
0° ~ 90°
Rotate
0° ~ 360°
Figure 2: Mount the Camera Figure 3: Adjust the Camera

V-6012B/V-6014B Installation and Setup Guide | Digital Monitoring Products 4
ACTIVATE THE CAMERA
After you’ve connected the camera to the network, activate it in Dealer Admin or Tech APP.
Dealer Admin
1. Log in to Dealer Admin.
2. Find the customer and select the relevant system. Select Edit.
3. In Video, enable Cameras & NVR, then press Save.
4. On the System Information page, press the Add Camera button and enter the camera’s MAC Address.
Press Next.
5. Enter a name for the camera.
6. Under Advanced, you can configure the following basic settings:
▶Video Quality
▶Flip Image
▶Record on Alarm
▶Time Zone
▶Observe DST
7. Press Save.
[email protected]
Figure 4: Add a V-6000 Camera in Dealer Admin

V-6012B/V-6014B Installation and Setup Guide | Digital Monitoring Products 5
Tech APP
1. Log in to Tech APP and select Video.
2. Find the customer and select the relevant system.
Select Edit.
3. In Video, enable Cameras & NVR, then press Save.
4. Tap the Add icon in the Cameras section.
5. When prompted to select a connection type, tap
Hardwired.
6. Enter the camera MAC Address. Press Next.
7. Enter a name for the camera.
8. Under Advanced, you can configure the following
basic settings:
▶Video Quality
▶Flip Image
▶Record on Alarm
▶Time Zone
▶Observe DST
9. Press Save.
Note: If you are experiencing issues with activating your camera, press and hold the reset button for 10 seconds
until the camera restarts, then try again.
Figure 5: Activate the Camera in Tech APP

V-6012B/V-6014B Installation and Setup Guide | Digital Monitoring Products 6
CONFIGURE MOTION DETECTION REGIONS
To use the camera without analytics, configure the camera motion detection regions.
1. Navigate to Dealer Admin and select the camera you want to add a motion detection region to.
2. In the Regions & Analytics section, select +Region and give it a Name.
3. Select the sensitivity of the region. Default is 50.
4. Dealer Admin will populate a 4-point rectangle in camera view screen. Click and drag an endpoint to change
the size of the region.
[email protected]
Figure 6: Select a V-6000 Camera in Dealer Admin
[email protected]
Figure 7: Configure a Motion Detection Region in Dealer Admin

V-6012B/V-6014B Installation and Setup Guide | Digital Monitoring Products 7
CONFIGURE VIDEO ANALYTICS
To use the camera with analytics, configure the camera video analytics.
1. Navigate to Dealer Admin and select the camera you want to add video analytics to.
2. Enable video analytics by using the toggle next to Video Analytics.
3. In the Regions & Analytics section, select +Region or +Line Cross and give it a Name.
4. Select the sensitivity of the region. Default is 50.
5. If +Line Cross has been selected, use the drop down menu to choose whether the direction of the line cross will
be an Entry, Exit, or Both.
6. Select whether the region or line cross will detect People, Vehicles, or Both.
7. If +Region has been selected, Dealer Admin will populate a 4-point rectangle in camera view screen. Click and
drag an endpoint to change the size of the region. Up to 6 endpoints can be created and manipulated to create
a custom region. If +Line Cross has been selected, Dealer Admin will populate a 2-point line in the camera view
screen. Click and drag an endpoint to change the length of the line.
[email protected]
Figure 8: Select a V-6000 Camera in Dealer Admin
[email protected]
Figure 9: Configure Video Analytics in Dealer Admin

V-6012B/V-6014B Installation and Setup Guide | Digital Monitoring Products 8
ADDITIONAL INFORMATION
Video Privacy in Dealer Admin and Virtual Keypad
In Virtual Keypad, end users can choose to allow video access to technicians and dealers. When video access is
enabled, all Administrator level app users will receive a notification email. To enable video access, follow the steps
below.
1. Navigate to Virtual Keypad.
2. Go to Settings and select Video Privacy.
3. Use the toggle to grant technicans and dealers unlimited access to the video feed. Use the button to give
temporary access. The default is 12 hours, although access can be revoked instantly by pressing the Revoke
Access button.
Note: All cameras brought online will immediately be granted access to the video feed for 12 hours.
Replace the SD Card
Refer to Figure 10 for the location of the SD card slot.
1. Locate the replacement SD card and place it to the side.
2. Remove the SD card cover on the bottom of the camera.
3. Insert the SD card into the slot.
4. Reattach the SD card cover.
SD Card Cover
Mounting Base
Adjustment Knob
Figure 10: Camera Details

18205
Designed, engineered, and
manufactured in Springfield, MO
using U.S. and global components.
LT-2609 23231
INTRUSION • FIRE• ACCESS• NETWORKS
2500 North Partnership Boulevard
Springfield, Missouri 65803-8877
800.641.4282 | DMP.com
© 2023
ORDERING INFORMATION
V-6012B 2 MP Fixed Bullet Camera
V-6014B 4 MP Fixed Bullet Camera
Accessories
V-6010-JB Fixed Bullet Camera Junction Box
V-6000-PS 12 VDC Power Supply
V-SD32G 32 GB Replacement SD Card
V-SD64G 64 GB Replacement SD Card
SPECIFICATIONS
V-6012B 2 Megapixel Camera
Sensor and Lens
Image Sensor 2 MP, 1.28” CMOS
Network
IP Protocol IPv4
Hardware
Power Consumption
12 VDC Max 6.0 W
Weight 0.93 lbs (0.42 kg)
Dimensions 6.1” x 2.5” x 2.5”
(15.59 cm x 6.31 cm x 6.27 cm)
Housing Material Metal
Environmental
Operating Temperature -22°F to 140°F (-30°C to 60°C)
Operating Humidity 95% RH or less, non-condensing
V-6014B 4 Megapixel Camera
Sensor and Lens
Image Sensor 4 MP, 1/3” CMOS
Network
IP Protocol IPv4
Hardware
Power Consumption
12 VDC Max 4.0 W
Weight 0.93 lb (0.42 kg)
Dimensions 6.1” x 2.5” x 2.5”
(15.59 cm x 6.31 cm x 6.27 cm)
Housing Material Metal
Environmental
Operating Temperature -22°F to 140°F (-30°C to 60°C)
Operating Humidity 95% RH or less, non-condensing