Dnake E211 User manual

QUICK START GUIDE
E211

Please follow the user manual for correct installation and
testing. If there is any doubt please call our tech-supporting
and customer center.
Our company applies ourselves to reformation and
innovation of our products. No extra notice for any change.
The illustration shown here is only for reference. If there is
any difference, please take the actual product as the
standard.
The product and batteries must be handled separately from
household waste. When the product reaches the end of
service life and needs to be discarded, please contact the
local administrative department and put it in the designated
collection points in order to avoid the damage to the
environment and human health caused by any disposal. We
encourage recycling and reusing the material resources.
REMARK

CATALOG
Pictures .....................................................................1
Package Contents...................................................2
System Configuration ............................................3
System Diagram......................................................4
Installation................................................................7
Safety Instructions .................................................11
For specific operation instructions, please scan
the following QR code to obtain the full version
of the User Manual.

PICTURES
Answer/Hang up
Speaker
Microphone
Microphone mute
Volume increase
Volume decrease
Calling Master
Station/SOS/
Relay 3
DND/Relay 2
Unlock Relay 1
LED indicator light
Handset(Optional)
Answer/Hang up
Speaker
Microphone
Microphone mute
Volume increase
Volume decrease
LED indicator light
MODEL: E211H/E211A
MODEL: E211/E211W
1
DND/Relay 2
Calling Master
Station/SOS/
Relay 3
Unlock Relay 1

Quick Start Guide
Indoor Monitor
MODEL: E211/E211W
Screw
PACKAGE CONTENTS
Quick Start Guide
Indoor Monitor
MODEL: E211H/E211A
Screw
Bracket
Rear Cover
Diode
Wires
Diode
Wires Handset
2

System Configuration
SYSTEM CONFIGURATION
3

SYSTEM DIAGRAM
1. Power
The power interface of Indoor Monitor connects to 12V DC power.
+12V
GND
+12V
GND
Power Interface DC 12V
2. Network(PoE)
CAT-5e
Network
Standard RJ45 interface is for the connection with PoE switch or other
network switch.
PSE shall comply with IEEE 802.3af (PoE) and its output power not less than
15.4W and its output voltage not be less than 50V.
V+
AL1
AL2
AL3
AL4
AL5
AL6
AL7
AL8
GND +12V
GND
+12V
GND
485+
485-
Siren/Alarm
Power
RS485
Network
(PoE)
REC-
GND
MIC-
MIC+
GND
IN-DET
HOOK-DET
REC+
Handset(Optional)
Indoor Monitor
4

4. Siren/Alarm interface
Interface of alarm zones connects with normally-open or normally-closed
switch.
When the alarm zone is triggered, it will output 12V/100mA power.
Alarm
Normally-closed sensor
Normally-open sensor
Siren equipment
Enable to connect equipment with RS485 interface. RS485 interface can
output 12V/100mA power supply. If RS485 equipment to be connected
doesn't require the power supply, there is no need to connect to +12V.
+12V
GND
485+
485
RS485 Interface
+12V
GND
485+
485
RS485 Equipment
3. RS485 Interface
V+
GND
AL1
AL2
AL3
AL4
AL5
AL6
AL7
AL8
2.2K
2.2K
5

E211 Handset(Optional)
Conector to Monitor
Conector from Handset
REC-
GND
MIC-
MIC+
GND
IN-DET
HOOK-DET
REC+
5. Handset Interface
6

MODEL: E211/W211W(Surface Mounting-86 Mounting Box)
INSTALLATION
Product dimension: 100x184x25mm
Surface mounting product dimension: 100x184x28mm
Screws
Rear Cover
86 Mounting Box
[Suggestion]: The camera should be 1450〜
1550mm above the ground. The camera at this
height can capture human face perfectly.
Installation Instructions:
400~500mm
145 0 ~1550m m
Wall
7

[Suggestion]: The camera should be 1450〜
1550mm above the ground. The camera at this
height can capture human face perfectly.
Installation Instructions:
400~500mm
145 0 ~1550m m
Wall
MODEL: E211/W211W(Surface Mounting-118 Mounting Box)
Screws
118 Mounting Box
Rear Cover
Product dimension: 100x184x25mm
Surface mounting product dimension: 100x184x28mm
8

MODEL: E211H/W211A(Surface Mounting-86 Mounting Box)
Screws
Rear Cover
86 Mounting Box
Screws
[Suggestion]: The camera should be 1450〜
1550mm above the ground. The camera at this
height can capture human face perfectly.
Installation Instructions:
400~500mm
145 0 ~1550m m
Wall
Product dimension: 100x184x25mm
Surface mounting product dimension: 100x184x28mm
9

MODEL: E211H/W211A(Surface Mounting-118 Mounting Box)
Screws
Screws
118 Mounting Box
Rear Cover
[Suggestion]: The camera should be 1450〜
1550mm above the ground. The camera at this
height can capture human face perfectly.
Installation Instructions:
400~500mm
145 0 ~1550m m
Wall
Product dimension: 100x184x25mm
Surface mounting product dimension: 100x184x28mm
10

In order to protect you and others from harm or your device from damage,
please read the following information before using the device.
Do not install the device in the following places:
Do not install the device in high-temperature and moist environment or
the area close to magnetic field, such as the electric generator, transformer
or magnet.
Do not place the device near the heating products such as electric heater
or the fluid container.
Do not place the device in the sun or near the heat source, which might
cause discoloration or deformation of the device.
Do not install the device in an unstable position to avoid the property
losses or personal injury caused by the falling of device.
Guard against electric shock, fire and explosion:
Do not use damaged power cord, plug or loose outlet.
Do not touch the power cord with wet hand or unplug the power cord by
pulling.
Do not bend or damage the power cord.
Do not touch the device with wet hand.
Do not make the power supply slip or cause the impact.
Do not use the power supply without the manufacturer's approval.
Do not have the liquids such as water go into the device.
Clean Device Surface
Clean the device surfaces with soft cloth dipped in some water, and then
rub the surface with dry cloth.
Other Tips
In order to prevent damage to the paint layer or the case, please do not
expose the device to chemical products, such as the diluent, gasoline,
alcohol, insect-resist agents, opacifying agent and insecticide.
Do not knock on the device with hard objects.
Do not press the screen surface. Overexertion might cause flopover or
damage to the device.
Please be careful when standing up from the area under the device.
Do not disassemble, repair or modify the device at your own discretion.
The arbitrary modification is not covered under warranty. When any repair
required, please contact the customer service center.
If there is abnormal sound, smell or fume in the device, please unplug the
power cord immediately and contact the customer service center.
When the device isn’t used for a long time, the adaptor and memory card
can be removed and placed in dry environment.
When moving, please hand over the manual to new tenant for proper
usage of the device.
SAFETY INSTRUCTIONS
11

V1.2
600110154102