Doc's SGP-3 User manual

1 | P a g e

2 | P a g e
NOTE: Not for use on ceilings over 12 feet.
The SGP™is not designed to be stacked on other poles to make it reach higher than it was designed to
from the factory.
Any modifications or changes made to the SGP™from its original design are not supported by Doc’s
Industries, Inc.
The SGP™ comes pre-assembled and ready to use! Simply secure your screw gun following the
instructions in the “Securing a screw gun in the SGP™ casting” section on page 3.
SGP™- General safety warnings:
•Follow all safety instructions for the screw gun you are using with the SGP™.
•Keep work area clean and well lit. Make sure there are no trip hazards such as electrical cords, step
stools or other power tools.
•Do not operate tool in hazardous conditions.
•Keep children and bystanders away while operating the tool.
•Stay alert –do not use while tired or under the influence of drugs, alcohol or medication.
•Always use eye protection and other protective equipment such as a dust mask, boots, hard hat and
hearing protection appropriate for the conditions.
•Keep proper footing and balance at all times.
•Do not force the tool - use the correct screw gun setting & fasteners for your application.
•Be certain the screw gun is operating properly and is adjusted before lifting to the ceiling.
Most modern screw guns have a depth setting for the fastener and some include an automatic
trigger depression system.
•Disconnect the power source before making any adjustments.
•Maintain the SGP™- check for misalignment, binding or breakage of hose clamp or wire bale pin as
well as any other condition that may affect the tool during operation. If damaged, have the tool
repaired by a professional before use.

3 | P a g e
Adjusting the length of the SGP™pole:
a. The SGP™ can be used fully collapsed or extended. Adjust the length of your pole accordingly.
b. To adjust the telescoping pole to the desired length, remove the wire bale pin, extend the pole
and reinstall the pin.
c. To remove the wire bale pin, place your pointer finger and middle finger inside the loop and
your thumb above the latch. With a firm grip, pull up and away from the pole tool as shown
below.
d. Once the wire bale pin is removed, slide the outer pole down or up to the desired hole and
reinsert the wire bale pin. The inner pole tool section has holes every 2” on center for fine
adjustments.
e. Once the pole is adjusted to the desired length/height, lock the wire bale pin into place.

4 | P a g e
Securing a screw gun in the SGP™casting:
A. Insert the screw gun into the SGP™casting by approaching at about a 45-degree angle.
B. Rotate the screw gun until it is level with the casting and slide it all the way in until the grip of
the screw gun is pressed up against the grip section of the SGP™ casting.

5 | P a g e
C. The Makita® XSF03 has a built-in tool belt clip that cannot be removed easily. The SGP™ was
designed to allow the clip to pass though the opening in the casting. This allows it to sit properly
without having to make any modification to the tool.
D. The Hilti® SD 5000-A22 features a tool belt clip that must be removed to allow the tool to sit
flush against the SGP™casting. It is fastened with 2 x star-bit machine screws.

6 | P a g e
E. Secure the screw gun in place using the provided 90 –110 mm hose clamp. There are cut outs /
notches on the casting that indicate the proper placement of the hose clamp. Use the SGP™
compatibility chart & Hose Clamp Location Charts on pg. 9 & 10 for proper placement. Make
sure your screw gun is properly seated in the casting before tightening the hose clamp. Do not
over-tighten.
F. Check that the screw gun is parallel to the pole tool and casting. Check both horizontal and
vertical alignment of the screw gun. If not aligned properly, repeat step A.

7 | P a g e
Operating the SGP™:
A. Lift the fully adjusted and secured SGP™tool to the ceiling.
B. Make sure your screw gun is perpendicular to the substrate you are fastening into.
C. Always keep your back straight and keep the pole tool close to your body.
D. Apply lifting force to the pole to engage the screw gun tool’s magazine / driver. Start the screw
gun by pressing against the substrate.
E. Do not force the fasteners. Periodically check to make sure the screws are being properly driven
to the desired depth.
F. When the fastener is fully installed, carefully lower the tool and adjust for your next installation.
G. If electrical power to the screw gun is interrupted during use and the tool becomes jammed in
the ceiling, disconnect the electric power to the screw gun and clear the jam in a safe manner
before restoring electric power.

8 | P a g e
Troubleshooting the SGP™:
Q. Why won’t my screw gun turn on?
A. First check to make sure the battery is fully charged & properly inserted. Check to make sure the
screw gun’s reverse/forward switch is properly engaged and not set in between
reverse/forward.
Make sure your screw gun is installed and secured to the SGP™casting properly by following the
instructions for your specific model of screw gun using the SGP™compatibility chart & Hose
Clamp Location Charts on pg. 9 & 10. Make sure the SGP™hose clamp is properly tightened.
Q. Why does my screw gun stay on after I release pressure being applied to the substrate?
A. First check to make sure your screw gun tool is working properly. Some models feature a button
that keeps the tool on all the time or only on when the magazine attachment is pressed against
the substrate. If the screw gun is still spinning slowly or the light on the screw gun is staying on,
please refer to the screw gun manufacturer’s manual for troubleshooting assistance.
Q. Why won’t my SGP™pole extend?
A. The SGP™is primarily designed for overhead fastening into a variety of substrates including but
not limited to drywall board. Drywall board / gypsum board dust and particles can accumulate
in-between the telescoping pole sections of the SGP™. Make sure the poles are clean and free of
any dust or burs that may cause friction between the poles.
Q. I need replacement parts, where can I purchase them?
A. Please contact the distributor you originally purchased the SGP™from, if you are unable to
contact the original distributor of your tool, please contact us directly at 800-544-8706 and we
will direct you to the closest distributor in your area.
How-to Video Links:
Doc’s YouTube Channel: www.youtube.com/docsindustries

9 | P a g e

10 | P a g e

11 | P a g e