Docking Drawer 0290-00046(W) User manual

Docking Drawer
Install Manual Docking Drawer Slim USB Series
Applicable Models: 0290-00046(W) / 24
0290-00045(W) / 21
0290-00048(W) / 18
CAUTION — READ CAREFULLY
• Failure to follow these instructions can cause death or permanent injury.
Do not work on live electrical circuits! Make absolutely certain power is
off before connecting the device!
• ThereareinstructionsprovidedwiththeUSBchargingoutlet–readthose
instructionsinadditiontothese.
• Thisproductisfordry,indoorandpermanentinstallationsonly.
• Installthedeviceinaccordancewithallnationalandlocalelectricalcodes.
General Information–
• TheDockingDrawerSlimUSBSerieshasbeenlistedbyETLandcomplieswith
UL962aandCSA-22.2when installed in accordance with these instructions.
Do not install this product in a manner contrary to these instructions.
• TheDockingDrawerSlimUSBSeriesisdesignedforchargingpersonalelectronics
andotherlowpowerdevices.Itislimitedtoamaximumof3A@120VAC.
• Currentinstallationdiagrams,mountingdiagramsandwiringinstructionscanbe
foundintheDockingDrawerSpecicationLibrary.
Pleasevisitwww.dockingdrawer.comandclickontheSpecicationbutton.
Structure–
Power Cord Bracket
Receptacle Box
User Resettable Circuit Breaker
USB Charging Outlet
Cable Management Arms
0230-00006.r1
1/19/2016
1

Top View of Docking Drawer Slim USB, Mounted
MINIMUMWIDTHBEHINDDRAWERBOX
DockingDrawerSlimUSB24 / 0290-00046(W)= ≥17 1/2"
DockingDrawerSlimUSB21 / 0290-00045(W)= ≥16"
DockingDrawerSlimUSB18 / 0290-00048(W)= ≥14 1/2"
Side View of Docking Drawer Slim USB, Mounted
2
Preparing for a Docking Drawer Slim USB Installation–
To prepare for a successful Docking Drawer Slim USB installation please ensure that the cable
management arms are free and unobstructed by conrming following the specications:
• Thedistancefromthebackofthedrawertothe
wallwherethepowercordbracketmountsmust
beatleast3"asshown.
• Theminimuminteriordrawerboxheightmust
beatleast23/4"
• Thedrawerslidesmustbepositionedinsuch
aswaythatthedrawerextendsnomorethan
21"for0290-00046(W),18"for0290-00045(W)
and15"for0290-00048(W).
• Thecutoutforthereceptacleboxshouldbe
6 1/32"wideX215/64"high.Enlargingthecutout
by1/16"ineachdimensionisacceptableforease
ofmounting.Theinstallermustprovide(4)mounting
screwsforthereceptacleboxand(2)forthepower
cordbracket.
• Thereceptacleboxacceptsdrawerwallthicknesses
ofeither1/2"or5/8".
• Ensure that the arm mechanism is free and
unobstructed.

3
Installing the Docking Drawer Slim USB Outlet–
1. Withthedrawerclosedandthereceptaclebox in
position,markthelocationoftherearmounting
bracketsothatthearmsarecentered.
2.InsertDockingDraweroutletthroughthe
receptacleboxcutoutinthebackofthedrawer.
4.Installtherightrearmountingscrew
(notsupplied).
5.Mountthereceptaclebox.
6.Testmovement.Aligncablemanagementarms
sotheyarecenteredbetweenthedrawerbox
andthebackofthecabinetifnecessary.
7. PluginDockingDraweroutletintoanexisting
electricaloutlet.
3.ExtendtheDockingDraweroutletandinstall
theleftrearmountingscrew(notsupplied).


4
Removing the Receptacle Box–
ForasuccessfulDockingDrawerSlimUSBchargingoutletinstallation,itisNOTnecessarytoremovethe
receptacleboxfromthecablemanagementarms.However,ifthereceptacleboxneedstoberemoved,
pleasefollowthesestepstodisconnect/reconnectthereceptacleboxfromthecablemanagementarms.
1.Removethecablearmgroundconnection
insidethereceptacleboxbyremovingthe
greengroundscrewandringterminalas
shown.DO NOTremovethegroundwire
thatgoestothereceptacle.
4.Mountthepowercordbracketinthecorrect
locationonthebackwallbehindthedrawer
asshowninthedrawing.
5.Installthedrawerinthecabinet,andholdon
totheendofthearmassembly.
6.Passthewiresfromthecablemanagement
armsintothereceptacleboxandreattach
thebracketusingthescrewdriverand
(2)#10screws.
7.Securethereceptacleboxtothebackofthe
drawerusingtheinstallersuppliedhardware.
8.Reconnecttheblackwirefromthecircuit
breakertotheblackwirefromthecable
managementarmusingthebluewirenut.
9. DO NOT FORGET TO REATTACH THE
GROUND WIRE INSIDE THE RECEPTACLE
BOX. TORQUE SCREW TO 16-18 IN-LBS.
ENSURE THAT THE CIRCUIT BREAKER IS
WIRED IN SERIES WITH THE LINE (BLACK)
WIRE. SEE WIRE DIAGRAM.
2.Removethebluewirenutconnectingthe
blackwirefromthecablechaintotheblack
wiregoingtothecircuitbreaker.
3.UseaPhillipsheadscrewdrivertoremovethe
(2)#10screwsfrominsidethereceptaclebox.
Thiswillallowthecablearmbrackettobe
disconnectedfromthereceptaclebox.
MAKE SURE BOTH GROUND SCREWS
ARE SECURELY CONNECTED!
TORQUE TO 16-18 IN-LBS



DO NOT REMOVE


5
Reinstalling the Outlet–
Install the USB charging outlet in the receptacle
box before plugging in the Docking Drawer.
    •Afterthereceptacleboxhasbeencorrectlyinstalledinthe
backofthedrawerand(ifapplicable)allwirescorrectly
reattached,theUSBchargingoutletcanbeinstalled.
REMINDER: IF THE CABLE ARM GROUND WIRE WAS REMOVED DURING
INSTALLATION, MAKE SURE IT HAS BEEN REATTACHED AND TORQUED
PROPERLY. MAKE SURE THE CIRCUIT BREAKER IS WIRED IN SERIES WITH
THE LINE (BLACK) WIRE AS SHOWN IN THE WIRING DIAGRAM.
• FollowtheUSBchargingoutletinstructions(includedinoutletpackaging)
andconnecttheblack,white,andgreenwiresinaccordancewiththose
instructions.
Specications–
DockingDrawerSlimUSBTechnicalSpecications:
• DC(USB)Power:5.2V,12.5WduplexUSBchargingreceptaclewith
integratedon/offsafetyswitch.
• Maxratedcurrent@125VAC:3A.Circuitisprotectedby5Apopout
breakeraccessiblefromtheuserside.Designedforchargingpersonal
electronicdevicesonly.
Operation–
• InstructionsspecictotheUSBchargingoutletare
includedwiththeoutletitself.
• TheDockingDrawerSlimUSBoutletincludesa5Aresetta-
blecircuitbreaker.Breakertripisindicatedbythewhite
buttonprotrudingapproximately3/8”outfromthe
housing.Toreset,correctthesourceofovercurrent
andpushthewhitebuttonbackin.
Wiring Diagrams–
Receptacle Box Wiring



Green Wire (ground):
green screw
White Wire (neutral):
silver screw
Black Wire (line):
brass screw

Specicationssubjecttochange.Pleasevisitwww.dockingdrawer.comforthemostcurrentinformation.
121615
12893 Alcosta Blvd., Suite M, San Ramon, CA 94583
p530.205.3625 | f925.886.3824 | [e-mail]
www.dockingdrawer.com Member
6
Docking Drawer™
Application: CHARGING POWERING
Outlet Type Docking Drawer Slim (2-AC, 2-USB) Docking Drawer Slim USB (4-USB)
Style Drawer (2-AC/GFCI) Style Drawer Flush (2-AC/GFCI)
Cabinet Depth
≤24" ≤21" ≤18" ≤24" ≤21" ≤18" ≤24" ≤21" ≤18" ≤24" ≤21" ≤18"
Outlet Name
Docking
Drawer
24 Slim
Docking
Drawer
21 Slim
Docking
Drawer
18 Slim
Docking
Drawer 24
Slim USB
Docking
Drawer 21
Slim USB
Docking
Drawer 18
Slim USB
Style
Drawer
24
Style
Drawer
21
Style
Drawer
18
Style
Drawer
24 Flush
Style
Drawer
21 Flush
Style
Drawer
18 Flush
Part Number (White) 0290-
00031 (W)
0290-
00030 (W)
0290-
00047 (W)
0290-
00046 (W)
0290-
00045 (W)
0290-
00048 (W)
0290-
00013 (W)
0290-
00011 (W)
0290-
00049 (W)
0290-
00033 (W)
0290-
00032 (W)
0290-
00050 (W)
Cabinet Specications:
Maximum drawer
extension
21" 18" 15" 21" 18" 15" 20" 17" 14" 20" 17" 14"
Minimum width
behind drawer box
≥17 1/2"≥16" ≥14 1/2"≥17 1/2"≥16" ≥14 1/2"≥131/2" ≥12" ≥10 1/2" ≥131/2" ≥12" ≥10 1/2"
Minimum space
behind drawer box
3" 3" 3" 3" 3" 3" 4" 4" 4" 5" 5" 5"
Minimum interior
drawer box height
2 3/4"2 3/4"2 3/4"2 3/4"2 3/4"2 3/4" 4" 4" 4" 4" 4" 4"
Charging Receptacle Specications:
Tamper Resistant Yes NA NA NA
120V AC Outlets 2 0 NA NA
USB Ports 2 4 NA NA
Max Current
AC:3amps@120VAC
USB:3.6amps@5VDC USB4.2amps@5VDC NA NA
Powering Receptacle Specications:
Tamper Resistant NA NA Yes Yes
120V AC Outlets NA NA 2 2
GFCI NA NA Yes Yes
LED Indicator NA NA Yes Yes
Max Current NA NA 20amps 20amps
Features:
ETL Listed to UL962a Yes Yes Yes Yes
ETL Listed
to CSA-22.2
No Yes No No
Interlocking
Safety Feature
CircuitBreaker CircuitBreaker ManualResetThermostat ManualResetThermostat
Electrical
Connection
NEMA5-15P NEMA5-15P Hardwired Hardwired
Warranty 1Year 1Year 1Year 1Year
TEST
RESET
TEST
RESET