Dodge Journey2017 User manual

2017
JOURNEY
QUICK
REFERENCE
GUIDE

Stadium Tip ’n Slide (7 Passenger
Models)
To Move The Second-Row Passenger Seat For-
ward
NOTE:
Raise the 40% seatback/armrest before moving
the 60% seat, to allow for full seat travel.
To allow passengers to easily enter or exit the
third-row passenger seats move the Tip ’n Slide
control lever on the upper outboard side of the
seatback forward, and in one fluid motion, the
seat cushion flips upward and the seat moves
forward on its tracks.
To Unfold And Move The Second-Row Passenger
Seat Rearward
1. Move the seatback rearward until it locks in
place and then continue sliding the seat rear-
ward on its tracks until it locks in place.
2. Push the seat cushion downward to lock it in
place.
3. Adjust the seat track position as desired.
Rear Seat Lever Locations
1 — Forward/Rearward Adjustment Lever
2 — Recliner/Seatback Release Lever
3 — Tip ’n Slide Control Lever
Seat In Tip ‘n Slide Position
SEATS

For further information and applicable warnings
and cautions, please refer to your Owner’s Manual
at www.dodge.com/en/owners/manuals.
Comfort Features
Heated Seats
The front heated seats control buttons are located
within the climate or controls screen of the touch-
screen of the Uconnect system.
Heated Steering Wheel
The steering wheel contains a heating element
that heats the steering wheel to one temperature
setting. The heated steering wheel control button
is located within the Uconnect system. You can
gain access to the control buttons through the
climate screen or the controls screen.
For further information and applicable warnings
and cautions, please refer to your Owner’s Manual
at www.dodge.com/en/owners/manuals.
In-Floor Storage Bin With
Removable Liner
An in-floor storage bin is located behind each front
seat.
To Access The Bin
1. Position the front seat to at least a mid-track
position to provide easier access to the storage
bin.
2. Position the floor mat aside (if equipped).
3. Pull the door latch release-loop upward to re-
lease the latch and then forward to open the
bin door.
For further information and applicable warnings
and cautions, please refer to your Owner’s Manual
at www.dodge.com/en/owners/manuals.
In Floor Storage
CARGO FEATURES

Speed Control
When engaged, the Speed Control takes over ac-
celerator operations at speeds greater than
25 mph (40 km/h).
The Speed Control buttons are located on the right
side of the steering wheel.
NOTE:
In order to ensure proper operation, the Speed
Control system has been designed to shut down if
multiple Speed Control functions are operated at
the same time. If this occurs, the Speed Control
system can be reactivated by pushing the Speed
Control ON/OFF button and resetting the desired
vehicle set speed.
To Activate
Push the ON/OFF button. The Cruise Control Set
Indicator Light in the instrument cluster display
will illuminate. To turn the system off, push the
ON/OFF button a second time. The Cruise Control
Set Indicator Light will turn off. The system should
be turned off when not in use.
To Set A Desired Speed
Turn the Speed Control on. When the vehicle has
reached the desired speed, push the SET (-) but-
ton and release. Release the accelerator and the
vehicle will operate at the selected speed.
To Deactivate
A soft tap on the brake pedal, pushing the CANC
button, or normal brake pressure while slowing the
vehicle will deactivate Speed Control without eras-
Speed Control Switches
1 — CANCEL
2 — Push ON/OFF
3 — Push RES/Resume/Accel
4 — Push SET/Decel
SPEED CONTROL

ing the set speed memory. Pushing the ON/OFF
button or turning the ignition switch OFF erases
the set speed in memory.
To Resume Speed
To resume a previously set speed, push the
RES (+) button and release. Resume can be used
at any speed above 25 mph (40 km/h).
To Increase Speed
When the Speed Control is set, you can increase
speed by pushing the RES (+) button.
To Decrease Speed
When the Speed Control is set, you can decrease
speed by pushing the SET (-) button.
To Accelerate For Passing
Press the accelerator as you would normally. When
the pedal is released, the vehicle will return to the
set speed.
For further information and applicable warnings
and cautions, please refer to your Owner’s Manual
at www.dodge.com/en/owners/manuals.
Keyless Enter-N-Go — Passive
Entry
The Keyless Enter-N-Go Passive Entry system is
an enhancement to the vehicle’s Remote Keyless
Entry feature. This feature allows you to lock and
unlock the vehicle's door(s) and liftgate without
having to push the key fob lock or unlock buttons,
as well as starting and stopping the vehicle with
the push of a button.
To Unlock From The Driver Or
Passenger Side
With a valid Keyless Enter-N-Go key fob located
outside the vehicle and within 5 ft (1.5 m) of the
driver or passenger side door handle, grab either
front door handle to unlock the door automatically.
Grab The Door Handle To Unlock
PASSIVE ENTRY

To Lock The Vehicle
Both front door handles have buttons located on
the outside of the handle. With one of the vehicle’s
Keyless Enter-N-Go key fobs located outside the
vehicle and within 5 ft (1.5 m) of the driver's or
passenger front door handle, push the door handle
button to lock all four doors and liftgate.
Do NOT grab the door handle when pushing the
door handle lock button. This could unlock the
door(s).
Preventing Inadvertent Locking Of Passive Entry
Key Fob In Vehicle (FOBIK-Safe)
To minimize the possibility of unintentionally lock-
ing a passive entry key fob inside your vehicle, the
passive entry system is equipped with an auto-
matic door unlock feature which will function if
the ignition switch is in the OFF position.
FOBIK-Safe only executes in vehicles with passive
entry. There are three situations that trigger a
FOBIK-Safe search in any passive entry vehicle:
• A lock request is made by a valid passive entry
key fob while a door is open.
• A lock request is made by the passive entry
door handle while a door is open.
• A lock request is made by the door panel switch
while the door is open
When any of these situations occur, after all open
doors are shut, the FOBIK-Safe search will be
executed. If it finds a passive entry key fob inside
the car, the car will unlock and alert the customer.
NOTE:
The vehicle will only unlock the doors when a valid
passive entry key fob is detected inside the ve-
hicle. The vehicle will not unlock the doors when
any of the following conditions are true:
• The doors are manually locked using the door
lock knobs.
• Three attempts are made to lock the doors
using the door panel switch and then close the
doors.
Push The Door Handle Button To Lock

NOTE:
• After pushing the door handle button, you must
wait two seconds before you can lock or unlock
the doors, using either passive entry door
handle. This is done to allow you to check if the
vehicle is locked by pulling the door handle
without the vehicle reacting and unlocking.
• If passive entry is disabled using Uconnect
System, the key protection described in "Pre-
venting Inadvertent Locking of Passive Entry
Key Fob in Vehicle" remains active/functional.
• The Passive Entry system will not operate if the
key fob battery is dead.
Lock Or Unlock The Liftgate
With a valid Keyless Enter-N-Go key fob within
5 feet (1.5 meters) of the liftgate, push the elec-
tronic liftgate lock/unlock pad located to the left of
the liftgate handle to unlock the liftgate. Push the
button a second time to lock the liftgate.
For further information and applicable warnings
and cautions, please refer to your Owner’s Infor-
mation at www.dodge.com/en/owners/manuals.
Do NOT Grab The Handle When Locking Electronic Liftgate Lock/Unlock Pad

Remote Start — If Equipped
Push the remote start button on the key fob
twice within five seconds. Pushing the remote
start button a third time shuts the engine off.
With Remote Start, the engine will only run for
15 minutes (timeout) unless the keyless ignition is
placed in the ON/RUN position.
Before the end of 15-minute cycle, push and
release the unlock button on the key fob to unlock
the doors and disarm the vehicle security alarm (if
equipped). Then, prior to the end of the
15-minute cycle, push and release the ignition
START/STOP button.
The vehicle must be started with the key fob after
two consecutive timeouts.
For further information and applicable warnings
and cautions, please refer to your Owner’s Infor-
mation at www.dodge.com/en/owners/manuals.
Parkview Rear Back-Up Camera
You can see an on-screen image of the rear of your
vehicle whenever the gear selector is put into
REVERSE. The ParkView Rear Back-Up Camera
image appears on the display screen located on
the center stack of the instrument panel.
NOTE:
If the display screen appears foggy, clean the
camera lens located on the rear of the vehicle
above the license plate.
For further information and applicable warnings
and cautions, please refer to your Owner’s Manual
at www.dodge.com/en/owners/manuals.
Instrument Cluster Display
The instrument cluster display features a driver
interactive display that is located in the instru-
ment cluster. Pushing the controls on the left side
of the steering wheel allows the driver to select
vehicle information and Personal Settings.
Instrument Cluster Display Controls
REMOTE START SAFETY FEATURES INSTRUMENT CLUSTER
DISPLAY

• Push the up arrow button to scroll upward
through the main menus (Fuel Economy, Ve-
hicle Speed, Trip Info, Vehicle Info, Messages,
Units, System Set-Up, Turn Menu Off) and sub
menus.
• Push the down arrow button to scroll downward
through the main menus and sub menus.
• Push the right arrow button for access to main
menus, sub menus or to select a personal
setting in the setup menu.
• Push the BACK button to scroll back to a previ-
ous menu or sub menu.
Selectable Menu Items
The instrument cluster features a driver interac-
tive display that is located in the of the center of
the instrument cluster. Pressing the controls on
the left side of the steering wheel allows the driver
to select vehicle information and Personal Set-
tings. Press the up or down arrow buttons to scroll
through the main menu feature items. To enter the
submenu’s of a feature menu item press the right
arrow button then press the right arrow button to
select or reset the submenu feature items:
Radio Info Tire Pressure
Vehicle Info Messages
Fuel Economy Vehicle Speed
Trip Info Turn Menu Off
For further information and applicable warnings
and cautions, please refer to your Owner’s Manual
at www.dodge.com/en/owners/manuals.
AUTO Button
• Push the AUTO button on the Integrated Center
Stack (ICS) Climate Controls, OR on the radio
touchscreen when viewing the Climate Controls
Main Screen.
• Select the desired temperature by pushing the
up or down temperature buttons for the driver
or passenger.
• The system will maintain the set temperature
automatically.
Radio 8.4 Automatic Climate Controls
AUTOMATIC CLIMATE
CONTROLS

Air Conditioning A/C
• If the A/C button is pushed while in AUTO
mode, the system will exit AUTO mode and stay
in A/C. The mode and blower will retain the
closest mode and blower position to those used
in AUTO.
• MAX A/C sets the control for maximum cooling
performance.
• Press and release to toggle between MAX A/C
and the prior settings. The button on the touch-
screen illuminates when MAX A/C is on.
• In MAX A/C, the blower level and mode position
can be adjusted. Pushing other settings will
cause the MAX A/C operation to switch to the
prior settings and turn MAX A/C off.
SYNC Temperature Button
• Press the “SYNC” button on the touchscreen to
control the driver and passenger temperatures
simultaneously. Press the “SYNC” button on
the touchscreen a second time to control the
temperatures individually.
Air Recirculation
• Use Recirculation for maximum A/C operation.
• For window defogging, turn the recirculation
button off.
• If the recirculation button is pushed while in
the AUTO mode, the indicator light may flash
three times to indicate the cabin air is being
controlled automatically.
Climate Control Knobs