Dolmar MS-252 User guide

Original Instruction Manual
Originalbetriebsanleitung
Originální návod k obsluze
Pôvodnýnávod na obsluhu
Eredeti használati útmutató
Important:
Read this instruction manual carefully before putting the Brush Cutter/String Trimmer into operation and strictly observe the safety regulations!
Preserve instruction manual carefully!
Wichtig:
Lesen Sie vor Verwendung der Motorsense/des Motor-Rasentrimmers diese Bedienungsanleitung aufmerksam durch und halten Sie die
Sicherheitsregeln strikt ein! Bewahren Sie diese Betriebsanleitung sorgfältig auf!
Důležité:
Předuvedenímkřovinořezu/strunovésekačkydoprovozusidůkladněprostudujtetentonávodkobsluzeapečlivědodržujtebezpečnostní
směrnice!Návodkobsluzepečlivěuschovejte!
Dôležité:
Preduvedenímkrovinorezu/strunovejkosačkydoprevádzkysipozorneprečítajtetentonávodnaobsluhuastriktnedodržiavajtebezpečnostné
nariadenia!Tentonávodnaobsluhustarostlivouschovajte!
Fontos:
Abozótvágó/szegélyvágóelsőüzembehelyezéseelőttgyelmesenolvassaáteztahasználatiutasítást,ésszigorúantartsabeabiztonsági
előírásokat!Gondosanőrizzemegahasználatiutasítást!
MS-252 MS-253

ENGLISH (Original instructions)
Thank you very much for purchasing the DOLMAR Brush Cutter/String trimmer. We
are pleased to recommend to you the DOLMAR Brush Cutter/String trimmer which
is the result of a long development programme and many years of knowledge and
experience.
Please read this booklet which refers in detail to the various points that will
demonstrate its outstanding performance. This will assist you to obtain the best
possible result from your DOLMAR Brush Cutter/String trimmer.
SYMBOLS
You will note the following symbols when reading the instructions manual.
Read instruction Manual Wear eye and ear protection
(for String trimmer only)
Take Particular care and Attention Wearprotectivehelmet,eyeandear
protection (for Brush Cutter only)
Forbidden Do not use metal blades
(for String trimmer only)
Keep distance Top permissible tool speed
Flyingobjecthazard Fuel and oil mixture
NoSmoking Engine-Manual start
Noopenflame Emergency stop
Protective gloves must be worn First Aid
Kickback ON/START
Keep the area of operation clear of all
persons and pets OFF/STOP
Wear sturdy boots with nonslip
soles. Steel toed safety boots are
recommended.
Table of Contents Page
Symbols.........................................................................2
Safety instructions .........................................................3
Technical data ...............................................................7
Designation of parts.......................................................8
Assembly of engine and shaft .......................................9
Mounting of handle......................................................10
Mounting of protector...................................................11
Mounting of cutter blade or nylon cutting head............12
Fuels/refueling.............................................................13
Correct handling of machine........................................14
Points in operation and how to stop ............................14
Resharpening the cutting tool......................................15
Servicing instructions...................................................17
Storage........................................................................19
2

(1)
(3)
(2)
(4)
(5)(6)
General Instructions
Toensurecorrectoperation,userhastoreadthisinstructionmanualtomake–
himself familiar with the handling of the Brush Cutter/String trimmer. Users
insufficiently informed will risk danger to themselves as well as others due to
improper handling.
It is recommended only to lend the Brush Cutter/String trimmer to people who–
have proven to be experienced with Brush Cutter/String trimmers.
Always hand over the instruction manual.
Firstusersshouldaskthedealerforbasicinstructionstofamiliarizeoneselfwith–
the handling of an engine powered cutter.
Children and young persons aged under 18 years must not be allowed to operate–
the Brush Cutter/String trimmer. Persons over the age of 16 years may however
use the device for the purpose of being trained only whilst under supervision of a
qualified trainer.
Use Brush Cutter/String trimmers with the utmost care and attention.–
Operate the Brush Cutter/String trimmer only if you are in good physical condition.–
Perform all work calmly and carefully. The user has to accept liability for others.
NeverusetheBrushCutter/Stringtrimmerafterconsumptionofalcoholordrugs,–
or if feeling tired or ill.
Nationalregulationcanrestricttheuseofthemachine.–
Intended use of the machine
TheBrushCutter/Stringtrimmerisonlyintendedforcuttergrass,weeds,Bushes,–
undergrowth it should not be used for any other purpose such as Edging or hedge
cuttingasthismaycauseinjury.
Personal protective equipment
Theclothingwornshouldbefunctionalandappropriate,i.e.itshouldbetight–
fittingbutnotcausehindrance.Donotweareitherjewelryorclothingwhichcould
become entangled with bushes or shrubs.
Inordertoavoideitherhead,eye,handorfootinjuriesaswellastoprotectyour–
hearing the following protective equipment and protective clothing must be used
during operation of the Brush Cutter/String trimmer.
Alwayswearahelmetwherethereisariskoffallingobjects.Theprotective–
helmet (1) is to be checked at regular intervals for damage and is to be replaced
at the latest after 5 years. Use only approved protective helmets.
The visor (2) of the helmet (or alternatively goggles) protects the face from flying–
debris and stones. During operation of the Brush Cutter/String trimmer always
weargoggles,oravisortopreventeyeinjuries.
Wear adequate noise protection equipment to avoid hearing impairment (ear–
muffs(3),earplugsetc.).
The work overalls (4) protect against flying stones and debris. We strongly–
recommend that the user wears work overalls.
Special gloves (5) made of thick leather are part of the prescribed equipment and–
must always be worn during operation of the Brush Cutter/String trimmer.
WhenusingtheBrushCutter/Stringtrimmer,alwayswearsturdyshoes(6)witha–
nonslipsole.Thisprotectsagainstinjuriesandensuresagoodfooting.
Starting up the brush cutter
Please make sure that there are no children or other people within a working–
rangeof15meters(49ft),alsopayattentiontoanyanimalsintheworkingvicinity.
Before use always check that the Brush Cutter/String trimmer is safe for–
operation:
Checkthesecurityofthecuttingtool,thecontrolleverforeasyactionandcheck
for proper functioning of the control lever lock.
Rotation of the cutting tool during idling speed is not allowed. Check with your–
dealerforadjustmentifindoubt.Checkforcleananddryhandlesandtestthe
function of the start/stop switch.
SAFETY INSTRUCTIONS
Diagrammatic figure
15 meters
3

Start the Brush Cutter/String trimmer only in accordance with the instructions.
Do not use any other methods for starting the engine!–
Use the Brush Cutter/String trimmer and the tools only for such applications as–
specified.
OnlystarttheBrushCutter/Stringtrimmerengine,aftertheentireassembly–
is done. Operation of the device is only permitted after all the appropriate
accessories are attached!
Beforestartingmakesurethatthecuttingtoolhasnocontactwithhardobjects–
suchasbranches,stonesetc.asthecuttingtoolwillrevolvewhenstarting.
The engine is to be switched off immediately in case of any engine problems.–
Shouldthecuttingtoolhitstonesorotherhardobjects,immediatelyswitchoffthe–
engine and inspect the cutting tool.
Inspect the cutting tool at short regular intervals for damage (detection of hairline–
cracks by means of tapping-noise test).
Operate the Brush Cutter/String trimmer only with the shoulder strap attached–
whichistobesuitablyadjustedbeforeputtingtheBrushCutter/Stringtrimmer
intooperation.Itisessentialtoadjusttheshoulderstrapaccordingtotheuser’s
sizetopreventfatigueoccurringduringuse.Neverholdthecutterwithonehand
during use.
During operation always hold the Brush Cutter/String trimmer with both hands.–
Always ensure a safe footing.
Operate the Brush Cutter/String trimmer in such a manner as to avoid inhalation–
oftheexhaustgases.Neverruntheengineinenclosedrooms(riskofgas
poisoning). Carbon monoxide is an odorless gas.
Switch off the engine when resting and when leaving the Brush Cutter/ String–
trimmerunattended,andplaceitinasafelocationtopreventdangertoothersor
damage to the machine.
NeverputthehotBrushCutter/Stringtrimmerontodrygrassorontoany–
combustible materials.
Thecuttingtoolhastobeequippedwithit’sappropriateguard.–
Neverrunthecutterwithoutthisguard!
All protective installations and guards supplied with the machine must be used–
during operation.
Neveroperatetheenginewithfaultyexhaustmuffler.–
Shut off the engine during transport.–
Whentransportingtheequipment,alwaysattachthecovertothecuttingblade.–
Ensure safe position of the Brush Cutter/String trimmer during car transportation–
to avoid fuel leakage.
WhentransportingtheBrushCutter/Stringtrimmer,ensurethatthefueltankis–
completely empty.
WhenunloadingtheBrushCutter/Stringtrimmerfromthetruck,neverdropthe–
Engine to the ground or this may severely damage the fuel tank.
Exceptincaseofemergency,neverdroporcasttheBrushCutter/Stringtrimmer–
to the ground or this may severely damage the Brush Cutter/String trimmer.
Remember to lift the entire equipment from the ground when moving the–
equipment. Dragging the fuel tank is highly dangerous and will cause damage
andleakageoffuel,possiblycausingfire.
Iftheequipmentgetsheavyimpactorfall,checktheconditionbeforecontinuing–
work. Check the fuel system for fuel leakage and the controls and safety devices
formalfunction.Ifthereisanydamageordoubt,askourauthorizedservicecenter
for the inspection and repair.
Refuelling
Shutofftheengineduringrefuelling,keepawayfromopenflamesanddonot–
smoke.
Avoid skin contact with mineral oil products. Do not inhale fuel vapor. Always–
wear protective gloves during refuelling. Change and clean protective clothing at
regular intervals.
Take care not to spill either fuel or oil in order to prevent soil contamination–
(environmental protection). Clean the Brush Cutter/String trimmer immediately
after fuel has been spilt.
Avoid any fuel contact with your clothing. Change your clothing instantly if fuel–
has been spilt on it (to prevent clothing catching fire).
Inspect the fuel cap at regular intervals making sure that it can be securely–
fastened and does not leak.
Carefully tighten the fuel tank cap. Change location to start the engine (at least–
3 meters away from the place of refuelling).
Neverrefuelinclosedrooms.Fuelvaporsaccumulateatgroundlever(riskof–
explosions).
Only transport and store fuel in approved containers. Make sure the fuel stored is–
not accessible to children.
Resting•
Transport•
Refuelling•
Maintenance•
Tool Replacement•
3meters
3 meters
4

12
2
Method of operation
Only use the Brush cutter/String trimmer in good light and visibility. During the–
winterseasonbewareofslipperyorwetareas,iceandsnow(riskofslipping).
Always ensure a safe footing.
Nevercutabovewaistheight.–
NeverstandonaladderandruntheBrushcutter/Stringtrimmer.–
NeverclimbupintotreestoperformcuttingoperationwiththeBrushcutter/String–
trimmer.
Neverworkonunstablesurfaces.–
Removesand,stones,nailsetc.foundwithintheworkingrange.–
Foreign particles may damage the cutting tool and can cause dangerous kick-
backs.
Beforecommencingcutting,thecuttingtoolmusthavereachedfullworking–
speed.
Ifgrassorbranchesgetcaughtbetweenthecuttingtoolandguard,alwaysstop–
the engine before cleaning. Otherwise unintentional blade rotation may cause
seriousinjury.
Take a rest to prevent loss of control caused by fatigue. We recommend to take a–
10 to 20-minute rest every hour.
Caution:
Kickback
Diagrammatic
figure
Diagrammatic
figure
Kickback prevention
To avoid kickbacks, observe the following:
Operationwithinabladesegmentbetween12and2o’clockpresentspositive–
hazards,especiallywhenusingmetalcuttingtools.
Cuttingoperationswithinabladesegmentbetween11and12o’clock,and–
between2and5o’clock,mustonlybeperformedbytrainedandexperienced
operators,andthenonlyattheirownrisk.
Easy cutting with almost no kickback is possible within a blade segment between
8and11o’clock.
Cutting Tools
Employonlythecorrectcuttingtoolforthejobinhand.
MS252withcutterblade(StarBlade(4teeth),EddyBlade(8teeth)),MS253with
Nyloncuttinghead.
Neveruseotherbladesincludingmetalmultipiecepivotingchainsandflailblades.
Otherwiseseriousinjurymayresult.
Forcuttingthickmaterials,suchasweed,highgrass,bushes,shrubs,underwood,
thicket etc. (max. 2 cm dia. thickness). Perform this cutting work by swinging the
brush cutter evenly in half-circles from right to left (similar to using a scythe).
Maintenance instructions
Haveyourequipmentservicedbyourauthorizedservicecenter,alwaysusing–
only genuine replacement parts. Incorrect repair and poor maintenance can
shorten the life of the equipment and increase the risk of accidents.
Theconditionofthecutter,inparticularofthecuttingtooloftheprotectivedevices–
and also of the shoulder strap must be checked before commencing work.
Particular attention is to be paid to the cutting blades which must be correctly
sharpened.
Turn off the engine and remove spark plug connector when replacing or–
sharpeningcuttingtools,andalsowhencleaningthecutterorcuttingtool.
Kickback (blade thrust)
Whenoperatingthebrushcutter,uncontrolledkickbackmayoccur.–
This is particularly the case when attempting to cut within a blade segment–
between12and2o’clock.
Neverapplythebrushcutterwithinasegmentbetween12and2o’clock.–
Neverapplythissegmentofthebrushcutterbladetosolids,suchasbushes–
andtrees,etc.,havingadiameterinexcessof3cmorthebrushcutterwillbe
deflectedatgreatforcewiththeriskofinjuries.
5

Never straighten or weld damaged cutting tools.
Operate the Brush cutter/String trimmer with as little noise and contamination as–
possible. In particular check the correct setting of the carburetor.
Clean the Brush cutter/String trimmer at regular intervals and check that all–
screws and nuts are well tightened.
NeverserviceorstoretheBrushcutter/Stringtrimmerinthevicinityofnaked–
flames.
Always store the Brush cutter/String trimmer in locked rooms and with an emptied–
fuel tank.
Whencleaning,servicingandstoringtheequipment,alwaysattachthecoverto–
the cutting blade.
Observe the relevant accident prevention instructions issued by the relevant trade
associations and by the insurance companies.
Do not perform any modifications on the Brush cutter/String trimmer as this will
endanger your safety.
The performance of maintenance or repair work by the user is limited to those
activities as described in the instruction manual. All other work is to be done by an
AuthorizedServiceAgent.Useonlygenuinesparepartsandaccessoriesreleased
and supplied by DOLMAR.
Use of non-approved accessories and tools means increased risk of accidents.
DOLMAR will not accept any liability for accidents or damage caused by the use of
nonapprovedcuttingtoolsandfixingdevicesofcuttingtools,oraccessories.
First Aid
In case of accident make sure that a first-aid box is available in the vicinity of the
cutting operations. Immediately replace any item taken from the first aid box.
When asking for help, please give the following information:
Place of accident–
What happened–
Numberofinjuredpersons–
Kindofinjuries–
Your name–
Vibration
People with poor circulation who are exposed to excessive vibration may–
experienceinjurytobloodvesselsorthenervoussystem.Vibrationmaycause
thefollowingsymptomstooccurinthefingers,handsorwrists:“Fallingasleep”
(numbness),tingling,pain,stabbingsensation,alterationofskincolororofthe
skin.Ifanyofthesesymptomsoccur,seeaphysician!
Toreducetheriskof“whitefingerdisease”,keepyourhandswarmduring–
operation and well maintain the equipment and accessories.
6
For European countries only
EC Declaration of Conformity
The undersigned, Tamiro Kishima and Rainer Bergfeld, as authorized by Dolmar GmbH, declare that the DOLMAR machine(s):
Designation of Machine: Brush Cutter/String Trimmer
ModelNo./Type:MS252,MS253
Specifications:see“TECHNICALDATA”table
are of series production and
Conforms to the following European Directives:
2000/14/EC,2006/42/EC
Andaremanufacturedinaccordancewiththefollowingstandardsorstandardizeddocuments:
ENISO118061
The technical documentation is on file at:
DolmarGmbH,
JenfelderStraße38,AbteilungFZ,D22045Hamburg
The conformity assessment procedure required by Directive 2000/14/EC was in Accordance with annex V.
Measured Sound Power Level: 109.1 dB
GuaranteedSoundPowerLevel:111dB
3. 11. 2009
Tamiro Kishima
Managing Director
Rainer Bergfeld
Managing Director

TECHNICAL DATA MS-252, MS-253
Model
MS-252 MS-253
U handle Loop handle
Dimensions : length x width x height (without cutting blade) mm 1,770x620x410 1,770x340x220
Mass (without plastic guard and cutting blade) kg 4.5 4.4
Volume (fuel tank) L 0.5
Engine displacement cm324.5
Maximum engine performance kw 0.73at7,000min-1
Engine speed at recommended max. spindle speed min-1 8,800
Maximum spindle speed (corresponding) min-1 6,000
Maximum fuel consumption kg/h —
Maximum specific fuel consumption g/kwh —
Idling speed min-1 2,600
Clutch engagement speed min-1 3,600
Carburetor type WALBRO WYJ
Ignition system type Solid state ignition
Spark plug type NGKBM7A
Electrode gap mm 0.6 – 0.7
Vibration per
ISO 22867
Right handle
(Rear grip)
ahv eq m/s23.8 3.8
Uncertainty K m/s20.7 0.7
Left handle
(Front grip)
ahv eq m/s25.5 4.8
Uncertainty K m/s20.6 1.2
Sound pressure level average to
ISO 22868
LPA eq dBA 91.2 94.5
Uncertainty K dBA 1.8 2.4
Sound power level average to
ISO 22868
LWA eq dBA 102.9 106.1
Uncertainty K dBA 1.7 1.8
Fuel Mixed gas
(gasoline:DOLMARGenuineTwostrokeEngineOil=50:1)
Gearratio 14/19
7

DESIGNATION OF PARTS
GB DESIGNATIONOFPARTS
1 Fuel Tank
2 Rewind Starter
3 Air Cleaner
4 I-O Switch (on/off)
5 Spark Plug
6 Exhaust Muffler
7 Clutch Case
8RearGrip
9 Hanger
10 Handle
11 Control Lever
12 Control Cable
13 Shaft
14 Protector (Cutting tool guard)
15 GearCase
16 Handle Holder
17 Cutter Blade
18 NylonCuttingHead
19 Fuel Filler Cap
20 Starter Knob
21 Primmer Pump
22 Choke Lever
23 Exhaust Pipe
24 Waist Pad
(7)
(3)
(19)
(1)
(21)
(5)
(22)
(20)
(2)
(6)
(23)
MS-252
U Handle Type
MS-253
Loop Handle Type
8

ASSEMBLY OF ENGINE AND SHAFT
CAUTION:Beforedoinganyworkonthebrushcutter,alwaysswitchoffthemotor
and pull the spark plug connector off the spark plug.
Always wear protective gloves.
CAUTION: Startthebrushcutteronlyafterhavingassembleditcompletely.
Loosen the two bolts (1) and insert the main pipe (2) into the case clutch (3).–
Insert it up to the arrow-mark position. (Refer to the sketch on the right.)–
Ifitisdifficulttoinsert,turnthespline(4)alittleandreinsert.
Tighten the two bolts (1) uniformly on the right and left by Allen wrench supplied.– Arrow-mark
Swivel
Control cable
Round hole
End fitting
Connectors
How to mount the control cable
Remove the air cleaner cover.–
Putthecontrolcable(5)intotheadjustingcable(6).Shifttheswivel(7)andput–
thecableintotheswivel.Atthistime,becarefulthattheroundholeintheswivel
is oriented toward the fitting at the inner wire end.
Release the swivel and make sure that the inner wire fitting is placed in the hole.–
Mount the air cleaner cover.–
Connection of the switch cord
Connect the switch cords to the two cords from the engine by inserting one into–
the other.
Fix the cord connector by clamp.–
Insert
9

MOUNTING OF HANDLE
CAUTION:Beforedoinganyworkonthebrushcutter,alwaysstoptheengineand
pull the spark plug connector off the spark plug.
Always wear protective gloves!
CAUTION:Startthebrushcutteronlyafterhavingassembleditcompletely.
MS-252
MS-252
MS-253
to Engine
Arrow mark
For machines with Loop Handle models
Fix a barrier to the left side of the machine together with the handle for operator–
protection.
Make sure that the grip/barrier assembly is fitted between the spacer and the–
arrow mark.
WARNING:Donotremoveorshrinkthespacer.Thespacerkeepsacertain
distance between both hands. Setting the grip/barrier assembly close to
the other grip beyond the length of the spacer may cause loss of control
andseriouspersonalinjury.
For machines with U Handle models
Place the handle-fixing metal so that the handle with the control lever will be–
positionedontheright(therighthandgripside)asviewedfromtheengineside,
and the other handle on the left side.
Fit the groove of the handle-fixing material to the handle end. Fix provisionally the–
attached metal by hexagon socket bolt supplied.
Adjustthehandletoaneasytooperateposition,andtightensecurelythefour–
hexagon socket bolts uniformly on the right and left by Allen wrench.
Wrap the waist pad around the shaft so that the hanger (1) will protrude through–
the slit in the waist pad and the control cable and the cords (3) will also be
wrapped under the waist pad (2).
10

MOUNTING OF PROTECTOR
Tomeettheapplicablesafetyprovisions,onlythetool/protectorcombinationsas
indicated in the table must be used.
Be sure to use genuine DOLMAR cutter blades or nylon cutting head.
Thecutterblademustbewellpolished,freeofcracksorbreakage.Ifthecutter–
bladehitsagainstastoneduringoperation,stoptheengineandchecktheblade
immediately.
Polish or replace the cutter blade every three hours of operation.–
Ifthenyloncuttingheadhitsagainstastoneduringoperation,stoptheengine–
and check the nylon cutting head immediately.
Star Blade Eddy Blade
CAUTION:Theappropriateprotectormustalwaysbeinstalled,foryourownsafety
and in order to comply with accident-prevention regulations.
Operation of the equipment without the guard being in place is not
permitted.
Fix the protector (1) to the clamp (3) with two bolts M6 x 30 (2).–
Protector for metal blades Nyloncuttinghead Protector for cord cutter
Whenusingthestringhead,fittheprotector(6)intotheprotector(1),andtighten–
them with two nuts (5) and two screws (4).
11

MOUNTING OF CUTTER BLADE OR NYLON CUTTING HEAD
Turnthemachineupsidedown,andyoucanreplacethecutterbladeorthenylon
cutting head easily.
Loosen Tighten
Hex wrench
Hex wrench
Tighten
Loosen
Rotation
Insert the hex wrench through the hole in the gear case and rotate the receiver–
washer (3) until it is locked with the hex wrench.
Loosen the nut (1) (left-hand thread) with the socket wrench and remove the nut–
(1),andclampwasher(2).
With the hex wrench still in place.
Mount the cutter blade onto the shaft so that the guide of the receiver washer (3)–
fits in the arbor hole in the cutter blade. Install the clamp washer (2) and secure
the cutter blade with the nut (1).
[Tighteningtorque:1323Nm]
NOTE: Alwaysweargloveswhenhandlingthecutterblade.
NOTE: Thecutterbladefasteningnut(withspringwasher)isaconsumablepart.If
thereappearsanywearordeformationonthespringwasher,replacethe
nut.
NOTE: Theclampwasher(2),andnut(1)arenotnecessaryformountingthenylon
cutting head. The nylon head should go on top of the receiver washer (3).
Screw the nylon cutting head onto the shaft.–
Make sure that the blade is the left way up.–
12

FUELS/REFUELING
Handling fuel
Utmost care is required when handling fuel. Fuel may contain substances similar
to solvents. Refuel either in a well ventilated room or outdoors. Do not inhale fuel
vapors,avoidanycontactoffueloroilwithyourskin.
Mineral oil products degrease your skin. If your skin comes in contact with these
substancesrepeatedlyandforanextendedperiodoftime,itwilldesiccate.
Variousskindiseasesmayresult.Inaddition,allergicreactionsmayoccur.
Eyescanbeirritatedbycontactwithoil.Ifoilcomesintoyoureyes,immediately
washthemwithclearwater.Ifyoureyesarestillirritated,seeadoctorimmediately.
Fuel and oil mixture
The engine of the brush cutter is a high-efficiency two-stroke engine. It is run with
a mixture of fuel and two-stroke engine oil. The engine is designed for unleaded
regularfuelwithamin.octanevalueof91RON.Incasenosuchfuelisavailable,
youcanusefuelwithahigheroctanevalue.Thiswillnotaffecttheengine,butmay
cause poor operating behaviour.
A similar situation will arise from the use of leaded fuel. To obtain optimum engine
operationandtoprotectyourhealthandtheenvironment,onlyunleadedfuelshould
be used!
Forlubricatingtheengineuseatwostrokeengineoil(qualitygrade:TC3),whichis
added to the fuel. The engine has been designed to use specified two-stroke engine
oilatmixtureratioof50:1toprotecttheenvironment.Inaddition,alongservicelife
and a reliable operation with a minimum emission of exhaust gases is guaranteed.
It is absolutely essential to observe a mixture ratio of 50:1 (specified 2-stroke engine
oil),asotherwisereliablefunctionofthebrushcuttercannotbeguaranteed.
Observe the Safety Instructions on page 4.
25:1
+
Gasoline
 1,000cm3(1 liter)
 5,000cm3(5 liter)
 10,000cm3(10 liter)
20 cm3 40 cm3
100 cm3 200 cm3
200 cm3 400 cm3
50:1 25:1
The correct mixture ratio:
Gasoline:Specifiedtwostrokeengineoil=50:1or
Gasoline:Othermanufacturer’stwostrokeengineoil=25:1
recommended
Note: Forpreparingthefueloilmixturefirstmixtheentireoilquantitywithhalfof
thefuelrequired,thenaddtheremainingfuel.Thoroughlyshakethemixture
before filling it into the brush cutter tank. It is not wise to add more engine oil
than specified to ensure safe operation.
This will only result in a higher production of combustion residues which
will pollute the environment and clog the exhaust channel in the cylinder
aswellasthemuffler.Inaddition,thefuelconsumptionwillriseandthe
performance will decrease.
Refuelling
The engine must be switched off.
Thoroughlycleantheareaaroundthefuelfillercap(2),topreventdirtfrom–
getting into the fuel tank (1).
Unscrew the fuel filler cap (2) and fill the tank with fuel.–
Tightly screw on the fuel filler cap (2).–
Clean screw fuel filler cap (2) and tank after refueling.–
Storage of Fuel
Fuel cannot be stored for an unlimited period of time.
Purchase only the quantity required for a 4 week operating period. Only use
approved fuel storage containers.
13

CORRECT HANDLING OF MACHINE
(1)
Attachment of shoulder strap
Adjustthestraplengthsothatthecutterbladewillbekeptparallelwiththe–
ground.
Hanger
POINTS IN OPERATION AND HOW TO STOP
Observe the applicable accident prevention regulations.
Starting
Move at least 3 m away from the place of refuelling. Place the brush cutter on a
clean piece of ground taking care that the cutting tool does not come into contact
withthegroundoranyotherobjects.
Cold start
For machine with U Handle or Loop Handle
Push the I-O switch (1) in the direction shown by the arrow.–
Detachment
Inanemergency,pushthenotches(1)atbothsides,andyoucandetachthe–
machine from you.
Be extremely careful to maintain control of the machine at this time. Do not allow
the machine to be deflected toward you or anyone in the work vicinity.
WARNING:Failuretomaintaincompletecontrolofthemachineatallcouldresultin
seriousbodilyinjuryorDEATH.
First place the machine on the ground.–
Giveagentlepushontheprimerpump(2)repeatedly(7–10times)untilfuel–
comes into the primer pump.
Pushthechokelever(3)totheposition“– ”.
Firmlyholdtheclutchcasebyyourlefthand,asillustrated.–
Slowly pull the starter grip until resistance is felt and continue with a smart pull.–
Do not pull out the starter rope to its full extent and do not allow the starter handle–
toberetractedwithoutcontrol,butensurethatitisretractedslowly.
Repeat the starting operation until initial ignitions are heard.–
Whentheenginestart,returnthechokeleverto“– ”.Pleasenotethatthechoke
leverwillreturnto“ ”positionautomaticallywhenthethrottleleverisoperated
and the throttle is opened.
(3)
(2)
14

Run the engine for approximately one minute at a moderate speed before applying full throttle.–
Note: Ifthestarterhandleispulledrepeatedlywhenthechokeleverremainsat“– ”position,theenginewillnotstarteasilydueto
excessive fuel intake.
Incaseofexcessivefuelintake,removethesparkplugandpullthestarterhandleslowlytoremoveexcessfuel.Also,drytheelectrode–
section of the spark plug.
Caution during operation:
Ifthethrottleleverisopenedfullyinanoloadoperation,theenginerotationisincreasedto10,000min-1ormore.Neveroperatetheengineata
higherspeedthanrequiredandatanapproximatespeedof6,0008,000min-1.
Starting the warm engine
Sameasabove,exceptwithoutmovingthechokelever(chokeleverremainsintheposition“– ”).
RESHARPENING THE CUTTING TOOL
STOPPING
Releasethethrottlelever(6)fully,andwhentheenginerpmhaslowered,push–
theIOswitch(1)to“O”positiontheenginewillnowstop.
Be aware that the cutting head may not stop immediately and allow it to slow–
down fully.
CAUTION: Thecuttingtoolsmentionedbelowmustonlyberesharpenedbyan
authorizedfacility.Manualresharpeningwillresultinimbalancesofthe
cutting tool causing vibrations and damage to the equipment.
cutterblade(starblade(4teeth),eddyblade(8teeth))–
AnexpertresharpeningandbalancingserviceisprovidedbyAuthorizedService
Agents.
NOTE: Toincreasetheservicelifeofthecutterblade(starblade,eddyblade)it
maybeturnedoveronce,untilbothcuttingedgeshavebecomeblunt.
ADJUSTMENT OF LOW-SPEED ROTATION (IDLING)
Thecutterbladeorthenyloncuttingheadshouldnotrunwhenthecontrolleverisfullyreleased.Ifnecessary,adjusttheidlerpmusingtheidle
adjustingscrew.
Checking the Idling speed
Idlespeedshouldbesetto2,600min– -1.
If necessary correct it by means of the idle screw (the blade or the nylon cutting
head must not turn when the engine is on idle).
Screwinginthescrew(1)willcauseanincreaseintheenginespeed,whereas
backing off the screw will reduce the engine speed.
Slow High
15

NYLON CUTTING HEAD
The nylon cutting head is a dual string trimmer head capable of both automatic and
bump & feed mechanisms.
The nylon cutting head will automatically feed out the proper length of nylon cord by
thechangesincentrifugalforcecausedbyincreasingordecreasingrpms.However,
tocutsoftgrassmoreefficiently,bumpthenyloncuttingheadagainstthegroundto
feed out extra cord as indicated under operation section.
Operation
Increasethenyloncuttingheadspeedtoapprox.6,000min– -1.
Lowspeed(under4,800min-1)isnotsuitable,thenyloncordwillnotfeedout
properly at low speed.
The most effective cutting area is shown by the shaded area.–
If the nylon cord does not feed out automatically proceed as follows:
1. Releasethethrottlelevertoruntheengineidleandthensqueezethethrottle
lever fully. Repeat this procedure until the nylon cord feeds out to the proper
length.
2. Ifthenyloncordistooshorttofeedoutautomaticallywiththeaboveprocedure,
bump the knob of the nylon cutting head against the ground to feed out the
nylon cord.
3. Ifthenyloncorddoesnotfeedoutwithprocedure2,rewind/replacethenylon
cordbyfollowingtheproceduresdescribedunder“Replacingthenyloncord”.
Replacing the nylon cord
First,stoptheengine.–
Pressonthehousinglatchesinwardtoliftoffthecover,thenremovethespool.–
Most effective cutting area
Idle speed Full speed
Knob
Cover
Latches
Press
Press
Spool 80mm(31/8”)
For left hand rotation
Spool
100mm(315/16”)
Notches
Eyelets
Hookthecenterofnewnyloncordintothenotchinthecenterofthespool,with–
oneendofthecordextendingabout80mm(31/8”)morethantheother.
Then wind both ends firmly around the spool in the direction of the head rotation
(left-hand direction indicated by LH and right-hand direction by RH on the side of
the spool).
Windallbutabout100mm(315/16”)ofthecords,leavingtheendstemporarily–
hooked through a notch on the side of the spool.
Mount the spool in the housing so that the grooves and protrusions on the spool–
match up with those in the housing. Keep the side with letters on the spool visible
onthetop.Now,unhooktheendsofthecordfromtheirtemporarypositionand
feed the cords through the eyelets to come out of the housing.
16

Align the protrusion on the underside of the cover with the slots of the eyelets.–
Then push cover firmly onto the housing to secure it.
SERVICING INSTRUCTIONS
CAUTION: BeforedoinganyworkontheBrushcutter,alwaysswitchoffthemotor
andpulltheplugcapoffthesparkplug(see“Checkingthesparkplug”).
Always wear protective gloves.
CAUTION: Neverremovetherecoilstarterforyourself,whichmaycausean
accident.ItshouldbeaskedtotheAuthorizedServiceAgent.
Toensurealongservicelifeandtoavoidanydamagetotheequipment,thefollowingservicingoperationsshouldbeperformedatregular
intervals.
Daily checkup and maintenance
Beforeoperation,checkthemachineforloosescrewsormissingparts.Payparticularattentiontothetightnessofthecutterbladeornylon–
cutting head.
Beforeoperation,alwayscheckforcloggingofthecoolingairpassageandthecylinderfins.–
Clean them if necessary.
Perform the following work daily after use:–
Clean the Brush cutter externally and inspect for damage.•
Cleantheairfilter.Whenworkingunderextremelydustyconditions,cleanthefiltertheseveraltimesaday.•
Check the blade or the nylon cutting head for damage and make sure it is firmly mounted.•
Check that there is sufficient difference between idling and engagement speed to ensure that the cutting tool is at a standstill while the•
engineisidling(ifnecessary,reduceidlingspeed).
Ifunderidlingconditionsthetoolshouldstillcontinuetorun,consultyournearestAuthorizedServiceAgent.
CheckthefunctioningoftheIOswitch,thelockofflever,thecontrollever,andthelookbutton.–
Cleaning of air cleaner
Unscrew screw (1).–
Remove the air cleaner cover (3).–
Takeoutthespongeelement(2),washitinlukewarmwateranddryitcompletely.–
Aftercleaning,putbacktheaircleanercover(3)andfastenitwithscrew(1).–
NOTE: Ifthereisexcessivedustordirtadheringtotheaircleaner,cleanitevery
day. A clogged air cleaner may make it difficult or impossible to start the
engine or increase the engine rotational speed.
Cover
Protrusion
Slot of eyelet
17

Checking the spark plug
Only use the supplied universal wrench to remove or to install the spark plug.–
The gap between the two electrodes of the spark plug should be 0.6– – 0.7 mm
(0.024” – 0.028”).Ifthegapistoowideortoonarrow,adjustit.Ifthesparkplugis
cloggedwithcartonorfouled,cleanitthoroughlyorreplaceit.
CAUTION: Nevertouchthesparkplugconnectorwhiletheengineisrunning(danger
of high voltage electric shock). 0.6 mm – 0.7 mm
(0.024”–0.028”)
AnymaintenanceofadjustmentworkthatisnotincludedanddescribedinthismanualisonlytobeperformedbyAuthorizedServiceAgents.
Greasehole
Supply of grease to gear case
Supply grease (Shell Alvania 3 or equivalent) to the gear case through the grease–
holeevery30hours.(GenuineDOLMARgreasemaybepurchasedfromyour
DOLMAR dealer.)
Suction head in the fuel tank
The fuel filler (5) of the suction head is used to filler the fuel required by the–
carburetor.
A periodical visual inspection of the fuel filter is to be conducted. For that purpose–
openthetankcap,useawirehookandpulloutthesuctionheadthroughthetank
opening.Filtersfoundtohavehardened,beenpollutedorcloggeduparetobe
replaced.
Insufficient fuel supply can result in the admissible maximum speed being–
exceeded. It is therefore important to replace the fuel filter at least quarterly to
ensure satisfactory fuel supply to the carburetor.
Cleaning of mufer exhaust port
Check of muffler exhaust port (6) regularly.–
Ifitiscloggedbycarbondeposits,carefullyscratchthedepositsoutwitha–
suitable tool.
18

Whenthemachineisinstorageforalongtime,drainfuelfromthefueltankand–
carburetor,asfollows:Drainallfuelfromthefueltank.Disposeofproperlyandin
accordance with all local laws.
Remove the spark plug and a few drops of oil into the spark plug hole.–
Then,pullthestartergently,sothatoilcoverstheengineinsideandtightenthe
spark plug.
Cleardirtordustfromthecutterbladeandoutsideofengine,wipethemwitha–
oil-immersed cloth and keep the machine in a place as dry as possible.
Drain fuel Humidity
Fault location
Fault System Observation Cause
Engine not starting
or with difficulty
Ignition system Ignition spark O.K. Faultinfuelsupplyorcompressionsystem,mechanicaldefect
Noignitionspark IOswitchoperated,wiringfaultorshortcircuit,sparkplugor
connectordefective,ignitionmodulefaulty
Fuel supply Fuel tank filled Incorrectchokeposition,carburetordefective,fuelsupplylinebent
orblocked,fueldirty
Compression Nocompression
when pulled over
Cylinderbottomgasketdefective,crankshaftsealsdamaged,
cylinder or piston rings defective or improper sealing of spark plug
Mechanical fault Starter not engaging Brokenstarterspring,brokenpartsinsideoftheengine
Warm start problems Tank filled ignition
spark existing
Carburetorcontaminated,mustbecleaned
Engine starts but
dies
Fuel supply Tank filled Incorrectidlingadjustment,carburetorcontaminated
Fueltankventdefective,fuelsupplylineinterrupted,cableorIO
switch faulty
Insufficient
performance
Several systems
may simultaneously
be affected
Engine idling poor Airfiltercontaminated,carburetorcontaminated,mufflerclogged,
exhaust duct in the cylinder clogged
Maintenance schedule
General Engineassembly,screwsandnuts Visual inspection for damage and tightness
Check for general condition and security
After each refuelling Control lever
I-O switch
Functional check
Functional check
Daily Air filter
Cooling air duct
Cutting tool
Idling speed
To be cleaned
To be cleaned
Check for damage and sharpness
Inspection (cutting tool must not move)
Weekly Spark plug
Muffler
Inspection,replaceifnecessary
Check and if necessary clean the opening
Quarterly Suction head
Fuel tank
To be replaced
To be cleaned
Shutting down procedure Fuel tank
Carburetor
Empty fuel tank
Operate until engine runs out of fuel
STORAGE
19

DEUTSCH (Originalanweisungen)
HerzlichenGlückwunsch,dassSiesichfürdenKaufeinerMotorsense/eines
MotorRasentrimmersvonDOLMARentschiedenhaben.Wirfreuenuns,Ihnendie
Motorsense/denMotorRasentrimmervonDOLMARanbietenzukönnendiese
ErzeugnissesinddasErgebniseineslangenEntwicklungsprogrammsundvieler
Jahre an Erkenntnissen und Erfahrungen.
LesenSiedieseBroschüremitdetailliertenInformationenzudenverschiedenen
Punkten,diedieherausragendeLeistungdiesesProduktsdemonstrieren,
aufmerksamdurch.SokönnenSiedasbestmöglicheErgebnismitIhrerMotorsense/
IhremMotorRasentrimmervonDOLMARerzielen.
SYMBOLE
Beim Lesen der Betriebsanleitung werden Ihnen die folgenden Symbole begegnen:
Betriebsanleitung lesen AugenundGehörschutztragen
(giltnurfürMotorRasentrimmer)
Besondere Aufmerksamkeit erforderlich
Schutzhelm,Schutzbrilleund
Gehörschutztragen
(giltnurfürMotorsense)
Verboten
Keine Schneidmesser aus Metall
verwenden
(giltnurfürMotorRasentrimmer)
Abstand halten MaximalzulässigeWerkzeugdrehzahl
Gefahrdurchherumfliegende
Gegenstände KraftstoffÖlGemisch
Rauchverbot Manueller Motorstart
Offene Flamme verboten NotAus
Schutzhandschuhetragen Erste Hilfe
Rückschlagen EIN/START
Keine anderen Personen und keine
Tiere im Arbeitsbereich AUS/STOPP
Festes Schuhwerk mit rutschfesten
Sohlen tragen. Empfohlen werden
ArbeitsschutzschuhemitStahlkappen.
Inhaltsverzeichnis Seite
Symbole.......................................................................20
Sicherheitsanweisungen..............................................21
Technische Daten........................................................25
BezeichnungderBauteile............................................26
ZusammenbauvonMotorundAchse..........................27
MontierendesGriffs ....................................................28
MontierendesSchutzes..............................................29
Montieren des Schneidmessers/
NylonSchneidkopfs.....................................................30
Kraftstoff/Betankung....................................................31
Richtige Handhabung der Maschine ...........................32
Wichtige Betriebsschritte und Stoppen des
Werkzeugs...................................................................32
NachschärfendesSchneidwerkzeugs ........................33
Wartungsanweisungen................................................35
Aufbewahrung .............................................................37
20