Doss 43136336 User manual

Installation Instruction
Above Fireplace Pull Down TV Mount
INTRODUCTION：
Please read through these instructions completely to be sure you’re comfortable with this easy
install process. Also check your TV owner’s manual tosee if there are any special requirements
for mounting your TV.
If you do not understand these instructions or have doubts about the safety of the installation,
assembly or use of this product, contact your Customer Service.
CAUTION: Avoid potential personal injuries and property damage!
● This product is designed for use in wood stud, solid concrete, and concrete block walls
- DO NOT install into drywall alone!!
● Make sure that mounting screws are anchored into the center of the stud. Use a stud
finder to locate the edge of the wood stud, then draw stud center line in the middle
point of the edges.
● The wall must be capable of supporting five times the weight of the TV and mount combined.
● Do not use this product for any purpose not explicitly specified by manufacturer.
● Manufacturer is not responsible for damage or injury caused by incorrect assembly or use.
● The temperature at the front of the fireplace mantle must never exceed 45℃（113℉）
IMPORTANT SAFETY INSTRUCTOPNS
TOOLS NEEDED FOR ASSEMBLY
Wood Stud Install
Con creteInstall
Wrench Pencil Level
Screw
driver
Electric
D rill
Socket
W rench
Stud
Finder
W ood
Drill Bit
Masonry
D rillBit H amm er
(3/8 in.)
10 mm
(7/32in.)
5.5 mm
Model
Display size
Minimum display weight
Maximum display weight
Minimum VESA size
Maximum VESA size
Swivel range
Tilt range
Rotation range
43136336
40”-65”
7.5kgs(16.5lbs)
35kgs (78lbs)
200X200mm
600x400mm
+/- 45°
+5°/-15°
+/- 5°
Mount your television conveniently
above your fireplace using this Above
Fireplace Mount.
The mount allows you to keep
the TV safely up and out of the way
when not in use, then you can pull
it down to eye level for comfortable
viewing

PART INCLUDED
WARNING:This product contains small items that could be a choking hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. If any
parts are missing or damaged, do not return the damaged item to your dealer;
contact Customer Service. Never use damaged parts!
NOTE: Not all hardware included will be used.
Parts for assembly
Hardware
01 02 03 04
05 x2
09 M8x10mm x4
14 M6 Nut x4
18 M8x45mm x4
23 6mm washer x4
27 M8x60 Lag Bolts x4 28 ￠8 washer x4 29 Plastic wall Anchor x4
24 5mm washer x4 25 ￠5 plastic spacer x4 26 ￠8 plastic spacer x4
19 M8x22mm x4 20 M6x30mm x4 21 M6x16mm x4 22 M5x16mm x4
15 5mm Hex key x1 16 6mm Hex key x1 17 8mm Hex key x1
10 M8x14mm x4 11 M6x10mm x6 12 ￠6 washer x4 13 plastic washer x4
01 x1 02 x1 03 x2 04 x1
06 x1 08 x207 x1

16 in.
ASSEMBLY
STEP 1: Assemble Your Wall Plate
STEP 2.1: Attach Wall Plate to Wall ( Wood Stud Option )
27 2728
03 02 10
Assemble Wall plate onto Wall plate as illustrated. Secure using four screws
in the holes shown (Use 6mm hex key ) ( fig 1.1 )
16
CAUTION: Avoid potential personal injuries and property damage!
● Drywall covering the wall must not exceed 16 mm. (5/8 in )
● Minimum wood stud size: 51 x 102 mm. (2 x 4 in ) or 38 x 89 mm. (1.5 x 3.5 in)
● Horizontal space between fasteners: 406 mm. (16 in)
1: Locate your stud. Verify and mark the center of the stud by finding the stud edges using a pencil
and an edge-to-edge stud finder. ( fig 2.1 2.2 )
2: Drill pilot holes using a 5.5 mm. (7/32 in ) diameter drill bit. ( fig 2.3 )
3: Install wall plate assembly using four lag bolts and Washer . Tighten the lag bolts only
until they are pulled firmly against the wall plate assembly . do not over tighten. Over tightening
can damage the screw , reducing it's holding power.
16 in.
(406 mm)
03
10 16
02
1.1
2.1 2.2

STEP 2.2: Attach Wall Plate to Wall ( Solid Concrete or Concrete Block Option )
3.1
2.4
75mm(3 in)
5.5mm
(7/32 in)
2.3
3.2
CAUTION: Avoid potential personal injury or property damage! All lag bolts MUST BE firmly
tightened to prevent unwanted movement of the wall plate assembly. Ensure the
wall plate is securely fastened to the wall before continuing on to the next step 3.
IMPORTANT: Be sure to drill into the center of the stud.
IMPORTANT: Pilot holes must be drilled to a depth of 75 mm. (3 in ).
CAUTION: Avoid potential personal injuries and property damage!
● Mount the wall plate assembly directly onto the concrete surface
● Minimum solid concrete thickness: 140 mm. (8 in)
● Minimum concrete block size: 203 x 203 x 406 mm. (8 x 8 x 16 in)
1. Position the wall plate template on the wall at your desired height. Level the wall plate and mark
the hole locations. (fig 3.1)
2. Drill four pilot holes using a 10 mm. (3/8 in) diameter masonry drill bit. (fig 3.2)
IMPORTANT: Pilot holes must be drilled to a depth of 75 mm. (3 in). Never drill into the mortar
between blocks.
10mm
(3/8 in.)
75mm(3 in)
27 28
CAUTION:
DO NOT
install into
drywall alone

STEP 3: Attach TV Bracket to TV
27
2929
29
27 28
05
2728
3.3 3.4
3. Insert four anchors , Be sure the anchors are seated flush with the concrete surface.(fig 3.3)
4. Install wall plate assembly using four lag bolts and four washers . Tighten the lag bolts
only until they are pulled firmly against the wall plate assembly. but do not over tighten. Over
tightening can damage the screw , reducing it's holding power. (fig 3.4)
M6M5 M8
1.Select TV Screw Diameter
3.Attach the bracket to the back of the TV using the appropriate screws/washers (Flat Back) or
spacer/screw/washer (Round Back / Extra Space). (fig 4.1)
IMPORTANT: Ensure TV bracket is securely fastened before moving on to the next step.
2. Select TV Screw Length
Hand thread screws into the threaded
inserts on the back of your TV to determine
whichscrew diameter ( M5,M6 or M8 ) to
use.
FLAT BACK ROUND BACK CABLESINSET HOLES
If your TV has a flat back AND you want your TV closer to the
wall, use the shorter screws.
Spacers and longer screws are supplied to accommodate:
●Round/irregular back TVs
●TVs with inset mounting holes
●Extra space needed for cables
Too Long
Too Short
Correct
CAUTION:
Verify adequate thread
engagement with your
screw/washer/spacer
combination AND
TV bracket
-Too short will not hold the TV.
-Too long will damage the TV.

STEP 4: Assemble Your Bracket Part A
04
13 12 14
01
10
10
15
15
10
05
05
05
18 19
23 24
25 26
20 21 22
06
06
06
07
07
10
4.1
Assemble front panel onto TV bracket as illustrated. (fig 5.1)
Secure using four plastic washer , four steel washer and four nut in the corner
holes shown.
04
13
12
14
01
5.1
STEP 5: Attach Bracket Part A to Wall Plate
09
16
08
1.Hang the Bracket part A onto the wall plate assembly by four screw .
(Use 6mm hex key ) (fig 6.1)
2.Attach the wall plate cover to the wall board.(fig 6.2)
HEAVY! You may need assistance with this step.
4.Place a towel or blanket on a flat surface, then place your television face down on it Using the
two screws , attach the connecting rod to the bracket . Then, using the four screws ,
attach the handle to the connecting rod . (By 5mm hex key )(fig 4.2)
4.1 4.2

STEP 6: Hang TV onto Bracket Part A
HEAVY! You may need assistance with this step.
16
05 04
05
04
09
08
part A
4.16.1 6.2
7.1
Two people lift the TV and hang the bracket
on the front panel . Then use a Philips
screwdriver to tighten the two locking screws,
which secures the bracket to the front panel
(fig 7.1)
TV ADJUSTMENTS
17
Adjust the spring pressure to balance the weight of the display so that it can be easily moved and
will maintain its position using either a ratchet wrench or the hex key provided. (fig 8.1)
Tilt adjustment
Loosen the tilt lock knob on side, adjust the TV to desired view angle. Then tighten the knob
Horizontal level adjustment
Slightly loosen the four nuts counterclockwise. Hold TV and gently turn to desired position.
When level, re-tighten the nuts to lock in the position.
(fig 8.2)

17
8.1 8.2
knob
140°
+/- 5°
+/- 45° +/- 18°
180mm
550mm
+5°
-15°