Griffin Technology XX-388W User manual

Company information
and Support
www.Griffin-Stands.com
Sliding
Keyboard Stand
with Boom Mic
www.Griffin-Stands.com
www.Griffin-Stands.com
Griffin™ stands and accessories are manufactured
in several innovative factories responsible for
developing products that address the newest
needs and trends of the current market. We take
pride in the Griffin™ brand and endeavor to be on
the forefront of the musical stands and musical
and lighting accessories market.
Performance Issue, Uneven or Unstable- Make
sure all nuts and bolts are tight on the product. If they
are, then loosen all nuts and bolts 1 full turn counter-
clockwise, then go back and tighten each bolt only ½
turn tight. Then do a final tighten turn for another ½
turn tight. Next, Make sure there are not any missing
nuts or bolts. Third, ensure all parts on the product
are not broken or defective. Finally, Re-read the
assembly instructions or watch the product
demonstration video to ensure you have correctly
assembled or are using the product properly with
factory specifications.
Missing Parts- The pictures, videos and images
shown in this manual might have changed style or
count due to the product being redesigned. So in rare
cases the part may no longer be included or of a
different style. However, if you think you are missing
a part that is necessary to the assembly and use of
your product, then first carefully double check all
packaging for any parts you think are missing. Some
parts might be hiding in the packaging or loose in an
inner box.
User Manual
M o d e l # X X - 3 8 8 W
Griffin | 11408 Hwy 64 W, Tyler, TX 75704 |
[email protected] | www.Griffin-
Stands.com
Product Specifications
For current product specifications, please to go
www.griffin-stands.com and type the model number
into the search bar. Locate the product listing to view
the current factory specifications. Thank you for purchasing the Griffin Sliding Keyboard
Stand with Boom Mic. Your product comes with a 1
year factory warranty from purchase date. Please
read all assembly instructions prior to assembling
your new cart. Pictures that may aid in assembly can
be found by going to www.griffin-stands.com and
typing XX-388W into the search bar.
Thank you for your Purchase
Trouble Shooting

Assembly and
Demonstration
Video
Assembly Instructions
Step 1 – Take the Parts K
(back leg), P(long
horizontal leg) and H(red
main post). Place Part K at
the bottom of the red
main post by using Part A
(T-Plate) to secure the
legs to the main post.
Please scan the QR Code below for the product
demonstration video. Or go to the URL shown here and find
the product video. www.Griffin-Stands.com/Videos
Step 2 – Now,
assemble the
keyboard holders.
Take the Part J (joint
arms connector) and
Part Q (support arms),
then check the
internal plastic
sleeves where Part Q
Align the bolt slots to the ones on the red main post,
use bolts labeled Part C. Insert all 4 bolts into the holes
first through the Part A (T-Plate), then into the legs
(Part P and K) and finally in to the main column shaft
(Part H). Important. Do not screw in fully any bolt until
all 4 bolts are fully inserted. Then take the front Legs
(Part P) and insert it under T-plate just below the Part K
and screw in. Tightly screw the bolts one turn at a time
for each bolt to make sure that no bolt is adding too
much tension on one side, this will also make sure that
the stand will be leveled. Please see Figure 1.
(mounting arms) will be inserted. Check the sleeves to
make sure that the holes are all lined up to the outer
holes of Part J. You might need to adjust the sleeves
inside Part J (joint), so that they will line up. Once done,
insert Part Q (mounting arms) and line up the holes as
shown in Figure 2.
Step 3 – Turn the part assembled above and screw in by
using Part B (bolts) and adding Part D (washers). (See
Figure 3) Repeat step 2 and 3 for the other keyboard
mount
.
Step 4 – Take the keyboard
mount assembled from the
step above and slide in to
the track of the main red
post from the bottom going
up. (See Figure 4) Once you
are satisfied with the
position of the mount there
is a small bolt on the side,
tighten it to secure the
mount’s location as shown in Figure 5. Do the same thing
with the second mount. To adjust the height and distance
between the two mounts, simply loosen the bolt, these
mounts are fully adjustable depending on your preference.
Step 5 – Take Part L which is the microphone boom adapter
and screw on to the top of the red main post. Make sure to
screw it on vertically at the screw post and not on an angle.
This will make it easier to be screwed on. (See Figure 6)
While screwing it on, hold the chrome adapter of the screw
post on the red main post and counter the spin of the boom
adapter.
Step 6 – To adjust the angle of
the boom microphone arm,
loosen the knob as shown in
Figure 7. To adjust the length
of the arm, loosen the knob
just below the arm as shown in
Figure 8. Tighten these knobs
to secure the angle and length
you preferred.
Step 7 – As shown in
Figure 9, you can now
place your equipment
on the mounts. These
mounts have lips that
will secure your
equipment from falling
and rubber resting pads
to keep your equipment
from being scratched
against the metal
mount.
Step 8 – For safety reasons, please always make sure to
test the stability and safety of the product before use.
Double check all nuts and bolts, knobs and connectors,
make sure that these are tight and securely fastened
before use of your product. Test the product under
light use or light loads the first time to confirm
assembly and structure of the product is correct.