Draper 56102 User manual

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURE THE
SAFE AND EFFECTIVE USE OF THIS PRODUCT.
INSTRUCTIONS
These instructions accompanying the product are the original instructions. This document is part of the product,
keep it for the life of the product passing it on to any subsequent holder of the product. Read all these
instructions before assembling, operating or maintaining this product.
This manual has been compiled by Draper Tools describing the purpose for which the product has been
designed, and contains all the necessary information to ensure its correct and safe use. By following all the
general safety instructions contained in this manual, it will ensure both product and operator safety, together
with longer life of the product itself.
AlI photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the
product.
Whilst every effort has been made to ensure the accuracy of information contained in this manual, the Draper
Tools policy of continuous improvement determines the right to make modifications without prior warning.
230V
LAWN
MOWER
56102

1. TITLE PAGE
1.1 INTRODUCTION:
USER MANUAL FOR: 230V Lawn Mower
Stock No’s: 56102
Part No’s: LM32
As our user manuals are continually updated, users should make sure that they use
the very latest version.
Downloads are available from: http://www.drapertools.com/manuals
Draper Tools Limited
Hursley Road
Chandler’s Ford
Eastleigh
Hampshire
SO53 1YF
UK
Website: drapertools.com
Product Helpline: [phone]
General Fax: [phone]
1.3 UNDERSTANDING THIS MANUALS SAFETY CONTENT:
WARNING! – Information that draws attention to the risk of injury or death.
CAUTION! – Information that draws attention to the risk of damage to the product or
surroundings.
1.4 COPYRIGHT © NOTICE:
Copyright © Draper Tools Limited.
Permission is granted to reproduce this publication for personal and educational use
only. Commercial copying, redistribution, hiring or lending is prohibited.
No part of this publication may be stored in a retrieval system or transmitted in any
other form or means without written permission from Draper Tools Limited.
In all cases this copyright notice must remain intact.
1.2 REVISIONS:
Date first published January 2017.

2. CONTENTS
1. TITLE PAGE
1.1 INTRODUCTION..........................................................................................................2
1.2 REVISION HISTORY ..................................................................................................2
1.3 UNDERSTANDING THIS MANUAL ............................................................................. 2
1.4 COPYRIGHT NOTICE ................................................................................................. 2
2. CONTENTS
2.1 CONTENTS .................................................................................................................... 3
3. GUARANTEE
3.1 GUARANTEE ...............................................................................................................4
4. INTRODUCTION
4.1 SCOPE.........................................................................................................................5
4.2 SPECIFICATION ..........................................................................................................5
4.3 HANDLING AND STORAGE........................................................................................ 5
5. HEALTH AND SAFETY INFORMATION
5.1 GENERAL SAFETY INSTRUCTIONS FOR POWER TOOL USE ............................... 6
–1) Work area safety ................................................................................................6
–2) Electrical safety..................................................................................................6
–3) Personal safety...................................................................................................6
–4) Power tool use and care....................................................................................7
–5) Service ................................................................................................................ 7
5.2 SPECIFIC SAFETY INSTRUCTION FOR 230V LAWN MOWERS .............................7
–1) Training ...............................................................................................................8
–2) Preparation ......................................................................................................... 8
–3) Operation ............................................................................................................ 8
–4) Maintenance and storage .................................................................................. 9
5.3 CONNECTION TO THE POWER SUPPLY .................................................................9
6. TECHNICAL DESCRIPTION
6.1 IDENTIFICATION .......................................................................................................10
7. UNPACKING AND CHECKING
7.1 PACKAGING ............................................................................................................. 11
7.2 WHAT’S IN THE BOX?............................................................................................... 11
8. ASSEMBLING THE LAWN MOWER
8.1 FRONT/REAR WHEEL ASSEMBLY .........................................................................12
8.2 HANDLE ASSEMBLY.................................................................................................13
8.3 GRASS COLLECTION BOX ASSEMBLY .................................................................14
9. OPERATING INSTRUCTIONS
9.1 POWER SUPPLY ......................................................................................................15
9.2 SWITCHING ON ........................................................................................................ 15
9.3 CUTTING HEIGHT ADJUSTMENT............................................................................15
9.4 GRASS COLLECTION FILL INDICATOR ..................................................................16
9.5 GRASS COMB FEATURE .........................................................................................16
10. MAINTENANCE AND TROUBLESHOOTING
10.1 GENERAL MAINTENANCE ....................................................................................... 17
10.2 BLADE REPLACEMENT............................................................................................ 17
10.3 TROUBLESHOOTING GUIDE...................................................................................17
11. EXPLANATION OF SYMBOLS
11.1 EXPLANATION OF SYMBOLS ...................................................................................18
12. DISPOSAL
12.1 DISPOSAL .................................................................................................................19
DECLARATION OF CONFORMITY .............................................................................. ENCLOSED
- 3 -

3. GUARANTEE
3.1 GUARANTEE
Draper tools have been carefully tested and inspected before shipment and are guaranteed to be
free from defective materials and workmanship.
Should the tool develop a fault, please return the complete tool to your nearest distributor or
contact:
Draper Tools Limited, Chandler's Ford, Eastleigh, Hampshire, SO53 1YF. England.
Telephone Sales Desk: [phone] or:
Product Helpline [phone].
A proof of purchase must be provided.
If upon inspection it is found that the fault occurring is due to defective materials or workmanship,
repairs will be carried out free of charge. This guarantee period covering parts/labour is 12 months
from the date of purchase except where tools are hired out when the guarantee period is 90 days
from the date of purchase. The guarantee is extended to 24 months for parts only. This guarantee
does not apply to normal wear and tear, nor does it cover any damage caused by misuse, careless
or unsafe handling, alterations, accidents, or repairs attempted or made by any personnel other
than the authorised Draper warranty repair agent.
Note: If the tool is found not to be within the terms of warranty, repairs and carriage charges will be
quoted and made accordingly.
This guarantee applies in lieu of any other guarantee expressed or implied and variations of its
terms are not authorised.
Your Draper guarantee is not effective unless you can produce upon request a dated receipt or
invoice to verify your proof of purchase within the guarantee period.
Please note that this guarantee is an additional benefit and does not affect your statutory rights.
Draper Tools Limited.
- 4 -

4. INTRODUCTION
4.1 SCOPE
For the cutting of grass lawns. Suitable for medium garden lawns up to 400M2. Any other
application is considered misuse.
4.2 SPECIFICATION
Stock No’s. ............................................................................................................................... 56102
Part No’s. ................................................................................................................................. LM32
Rated Voltage ................................................................................................................. 230V~50Hz
Rated input ............................................................................................................................. 1300W
Cutting width ....................................................................................................................... 320mmØ
Grass collection box capacity........................................................................................................30L
Recommended maximum cutting area..................................................................................... 400M2
Adjustable cutting heights ............................................................................................ 30, 45, 60mm
Speed (no load) ............................................................................................................... 3,300min-1
Sound pressure level ................................................................................................. 75.31±3dB(A)
Sound power level ...................................................................................................... 95.43±3dB(A)
Single value noise level (LWA)†.......................................................................................... 96.dB(A)
Weight (machine only)..............................................................................................................11.2kg
†A-weighted sound pressure level in accordance to 2000/14/EC.
4.3 HANDLING AND STORAGE
Care must still be taken when handling and lifting. Dropping this machine will have an effect on the
accuracy and may also result in personal injury. This machine is not a toy and must be respected.
The environment will have a negative result on its operation if you are not careful. If the air is
damp, components will rust. If the machine is unprotected from dust and debris; components will
become clogged: And if not cleaned and maintained correctly or regularly the machine will not
perform at its best.
- 5 -

5. HEALTH AND SAFETY INFORMATION
Have this tool repaired by a qualified person. This tool is designed to conform to the relevant
international and local standards and as such should be maintained and repaired by someone
qualified; using only original parts supplied by the manufacturer: This will ensure the tool remains
safe to use.
5.1 GENERAL SAFETY INSTRUCTIONS FOR POWER TOOL USE
Warning: Read all safety warnings and all instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains operated (corded) power tool or
battery-operated (cordless) power tool, in this case it refers to a lawn mower.
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence flammable
liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool. Distractions can cause
you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets
will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is earthed or
grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power
tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled
cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use
of a cord suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use common sense when operating a power tool.
Do not use a power tool while you are tired or under the influence of drugs, alcohol or
medication. A moment of inattention while operating power tools may result in serious
personal injury.
b) Use personal protective equipment. Always wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate
conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off position before connecting to
power source and/or battery pack, picking up or carrying the tool. Carrying power tools with
your finger on the switch or energising power tools that have the switch on invites
accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key
left attached to a rotating part of the power tool may result in personal injury.
- 6 -

5. HEALTH AND SAFETY INFORMATION
e) Do not overreach. Keep proper footing and balance at all times. This enables better control
of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewellery or long hair can be caught in moving
parts.
g) If devices are provided for the connection of dust extraction and collection facilities, ensure
these are connected and properly used. Use of these devices can reduce dust-related
hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your application. The correct
power tool will do the job better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off. Any power tool that
cannot be controlled with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or battery pack from the power tool before
making any adjustments, changing accessories, or storing power tools. Such preventive
safety measures reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with
the power tool or these instructions to operate the power tool. Power tools are dangerous in
the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts
and any other condition that may affect the power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents are caused by poorly maintained power
tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc. in accordance with these instructions,
taking into account the working conditions and the work to be performed. Use of the power
tool for operations different from those intended could result in a hazardous situation.
5) Service
a) Have your power tool serviced by a qualified repair person using only identical replacement
parts. This will ensure that the safety of the power tool is maintained.
Important
On products exceeding 2000W it is recommended that the power cable and/or extension cable are
fully unwound before a connection is made to the power supply. However, ensure the residual
cable does not pose a trip hazard.
5.2 SPECIFIC SAFETY INSTRUCTIONS FOR 230V LAWN MOWERS
Warning: Connect the machine only to a supply circuit protected by a residual current device
(RCD) with a tripping current of not more than 30 MA.
– Keep bystanders away.
– Remove the plug from the socket before carrying out adjustment, cleaning or maintenance.
– Read user instructions before operating this machine.
– The lawn mower shall not be operated without either the entire grass catcher or the guard
in place.
Warning: Do not touch rotating blade.
– Beware of blades. Blades continue to rotate after the motor is switched off. Remove plug
from mains before maintenance or if cord is damaged.
- 7 -

5. HEALTH AND SAFETY INFORMATION
– Keep supply cord away from the blades. Blades can cause damage to the cords and lead
to contact with live parts.
1) Training
– Read the instructions carefully. Be familiar with the controls and the proper use of the
appliances.
– Never allow children or people unfamiliar with these instructions to use the appliance. Local
regulations may restrict the age of the operator.
– Never mow while people, especially children, or pets are nearby.
– The operator or user is responsible for accidents or hazards occurring to other people or
their property.
2) Preparation
– While mowing, always wear substantial footwear and long trousers.
– Do not operate the appliance when barefoot or wearing open sandals.
– Thoroughly inspect the area where the appliance is to be used and remove all stones,
sticks, wires bones and other foreign objects.
– Before using, always visually inspect to see that the blades, blade bolts and cutter
assembly are not worn or damaged. Replace worn or damaged blades and bolts in sets to
preserve balance.
– On multi-bladed appliances, take care as rotating one blade can cause other blades to
rotate.
– Prior to each use, thoroughly check the supply and extension cord for signs of damage or
ageing.
Warning: Do not use the lawn mower if the cords are damaged or worn.
3) Operation
Warning: Do not connect a damaged cord to the supply or touch a damaged cord before it is
disconnected from the supply. A damaged cord can lead to contact with live parts.
– Mow only in daylight or in good artificial light.
– Avoid operating the appliance in wet grass, where feasible.
– Always be sure of your footing on slopes.
– Walk, never run.
– For wheeled rotary mowers, mow across the face of slopes, never up and down.
– Exercise extreme caution when changing direction on slopes.
– Do not mow excessively steep slopes.
– Use extreme caution when reversing or pulling the appliance towards you.
– Stop the blade(s) if the appliance has to be tilted for transportation when crossing surfaces
other than grass, and when transporting the appliance to and from the area to be mowed.
– Never operate the appliance with defective guards or shields, or without safety devices, for
example deflectors and/or grass catchers, in place.
– Switch on the motor according to instructions and with feet well away from the blade(s).
rofdetlitebotsahecnailppaehtfitpecxe,rotomehtnognihctiwsnehwecnailppatlittonoD–
starting. In this case, do not tilt it more than absolutely necessary and lift only the part
which is away from the operator.
– Always ensure that both hands are in the operating position before returning the appliance
to the ground.
- 8 -

5. HEALTH AND SAFETY INFORMATION
– Do not put hands or feet near or under rotating parts. For rotary mowers, keep clear of the
discharge opening at all times.
Warning: Do not touch the blades before the machine is disconnected from the supply and
the blades have come to a complete stop.
– Never pick up or carry an appliance while the motor is running.
– Immediately disconnect the mains from the cord if it becomes damaged during use.
– Remove the plug from the socket.
•whenever you leave the machine;
•before cleaning a blockage;
•before checking, cleaning or working on the machine
•after striking a foreign object. Inspect the appliance for damage and make repairs as
necessary;
•if the appliance starts to vibrate abnormally (check immediately).
4) Maintenance and storage.
– Replace safety parts subjected to regular wear and tear.
– Keep all nuts, bolts and screws tight to be sure the appliance is in safe working condition.
– Check the grass catcher frequently for wear or deterioration.
– Replace worn or damaged parts for safety.
– For cylinder mowers, be careful during adjustment of the appliance to prevent entrapment
of the fingers between moving blades and fixed parts of the appliance.
– For rotary mowers, ensure that only replacement cutting means of the right type are used.
5.3 CONNECTION TO THE POWER SUPPLY
Caution: Risk of electric shock. Do not open.
This appliance is supplied with a moulded 3 pin mains plug for your safety. The value of the fuse
fitted is marked on the pin face of the plug. Should the fuse need replacing, ensure the substitute
is of the correct rating, approved to BS1362 and ASTA or BS Kite marked.
ASTA
BSI
The fuse cover is removable with a small plain slot screwdriver. Ensure the fuse cover is replaced
before attempting to connect the plug to an electrical outlet. If the cover is missing, a replacement
must be obtained or the plug replaced with a suitable type.
If a replacement plug is to be fitted this must be carried out by a qualified electrician.
The damaged or incomplete plug, when cut from the cable should be disabled to prevent
connection to a live electrical outlet.
This appliance is Class II†and is designed for connection to a power supply matching that detailed
on the rating label and compatible with the plug fitted.
If an extension lead is required, use an approved and compatible lead rated for this appliance.
Follow all the instruction supplied with the extension lead.
†Double insulated : This product requires no earth connection as supplementary insulation is
applied to the basic insulation to protect against electric shock in the event of failure of the basic
insulation.
Important: On products exceeding 2000W it is recommended that the power cable and/or
extension cable are fully unwound before a connection is made to the power supply. However,
ensure the residual cable does not pose a trip hazard.
- 9 -

6. TECHNICAL DESCRIPTION
6.1 IDENTIFICATION
 Handle grip bar.
 Start/Stop lever.
 Motor supply cord.
 Handle folding levers.
 Handle mounting levers.
 Centralised carrying handle.
 Grass comb.
 Front wheels.
 Rotary cutting blade.
 Rear wheels.
 Grass collection box.
 Grass collection box lid.
 Grass collection fill indicator.
 Deflector guard.
 Lower handle section.
 Upper handle section.
















- 10 -

7. UNPACKING AND CHECKING
7.1 PACKAGING
Carefully remove the machine from the packaging and examine it for any sign of damage that may
have happened during shipping. Lay the contents out and check them against the parts shown
below. If any part is damaged or missing; please contact the Draper Helpline (the telephone
number appears on the Title page) and do not attempt to use the machine.
The packaging material should be retained at least during the guarantee period: in case the
machine needs to be returned for repair.
Warning! Some of the packaging materials used may be harmful to children. Do not leave any of
these materials in the reach of children.
If any of the packaging is to be thrown away, make sure they are disposed of correctly; according
to local regulations.
7.2 WHAT´S IN THE BOX?
The packaging contains several parts and semi-assembled elements that require final assembly.
Lay out the contents and check off the items against those featured below.
 Handle folding levers
and fixings.
 Handle mounting levers
and fixings.
 Front wheels.
 Rear wheels.
 Grass collection box
 Grass collection box lid.
 Lower handle section.
 Upper handle section.
 Main mower motor/body.
 Cable restraint.
 Cable clips.
 Front/rear wheel fixings.
 Rear wheel caps.
 Front wheel caps.



 

 







- 11 -

8. ASSEMBLING THE LAWN MOWER
Warning: Do not connect the machine to the power supply before
the product is completely assembled.
8.1 FRONT/REAR WHEEL ASSEMBLY – STEPS 1 – 5
The use of a pair of long nose pliers (not supplied) is recommended
when assembling the following front/rear wheel components.
- 12 -


12
3
5
4




8. ASSEMBLING THE LAWN MOWER
8.2 HANDLE ASSEMBLY – STEPS 1 – 8
- 13 -
12
3
6
4
7 8
5










8. ASSEMBLING THE LAWN MOWER
- 14 -
8.3 GRASS COLLECTION BOX ASSEMBLY – STEPS 1 – 8
 12
3
6
4
5


- 15 -
9. OPERATING INSTRUCTIONS
9.1 POWER SUPPLY
Before you connect the equipment to the power
supply make sure that the data on the rating plate is
identical to the supply voltage.
Warning! Always remove the power
plug before making adjustments to
the equipment.
It is highly recommended that this
machine is used in conjunction
with a residual current device
(R.C.D) – Draper Stock No.69307.
9.2 SWITCHING ON – STEPS 1 – 2
12


9.3 CUTTING HEIGHT ADJUSTMENT
Warning! Always disconnect the mower from
the electrical supply before making any
adjustments to the cutting height.
The front and back wheels have independently
sprung locking axles that can adjust the height
of the rotary cutting blade to three cutting
height positions.
Important! Always check the condition of the
rotary blade before using the mower. Replace
any blunt or damaged blades.
Warning! Always ensure the blade is at a
standstill and the power supply is disconnected
before examining the rotary blade.
– To ensure an even cut, make sure that all four wheels are set to the same position. However, in
some situations having the front wheels one notch lower than the rear wheels may produce a
better result.

9. OPERATING INSTRUCTIONS
Wheel position Cutting height
30mm.
45mm.
60mm.
1
2
3
- 16 -
9.4 GRASS COLLECTION FILL
INDICATOR
When mowing, frequently check the amounts of
collected grass by lifting the small lid out
the top of the grass collection box.
Empty the collection box when grass trimmings
are near to capacity.
Failure to empty a full grass box will result in
less efficient cutting and possible damage to the
mower.
9.5 GRASS COMB FEATURE
This mower comes with protruding fins at
the front of the mower that lift the grass before
the blade cuts.
– To keep this feature at its most
effective, ensure any existing
grass debris on these fins are
removed.



1
2
3
9.3 CUTTING HEIGHT ADJUSTMENT (continued)

10. MAINTENANCE & TROUBLESHOOTING
10.1 GENERAL MAINTENANCE
Inspect the mower before each use for damage
or loose parts.
Clean the mower after each use and make
sure the blade is still sharp.
If the blade is blunt, have it sharpened
before the next time the mower is used.
Protect the blade against rusting by
covering it with oil or rust inhibitor when the
mower is stored for the winter.
10.2 BLADE REPLACEMENT
Warning: remove the plug from the socket
before carrying out adjustment, servicing or
maintenance.
– Using a cloth or thick glove, hold the blade
 and remove bolt using a suitable
spanner. Undo the bolt  in an
anticlockwise direction.
– Replace the blade and ensure the blade bolt
is fully tightened.
10.3 TROUBLESHOOTING GUIDE
Fault Remedy
Mower won’t
switch on.
1. Check mains power.
2. Check, and if necessary, replace fuse.
3. With the mower disconnected from the power supply, check the blade
rotates (there is some friction due to the brake). If the blade does not
move, contact a service repair agent.
Mower vibrates
in use.
Stop using immediately!
– Disconnect the mower from the power supply.
– Wait until the blade has completely stopped rotating.
– Check to see if the blade bolt is loose – tighten if necessary.
– If the blade bolt is already tight, contact Draper or service agent.
Mower does not
pick up
grass cuttings.
– Grass collection box is full – empty the box.
– Grass is wet – wait until grass is dry.
– The underside of the deck is clogged with grass cuttings – disconnect
the power supply and clean the underside of the deck.
Uneven cutting. – Cutting height set too low – set higher.
– Blade is blunt – re-sharpen or replace blade.
1
2
3
- 17 -


13
2

11. EXPLANATION OF SYMBOLS
96
Do not dispose of WEEE*
unsorted municipal waste.
Class II construction
(Double insulated).
Danger!
Risk of electrocution.
Warning!
Keep bystanders away.
Warning!
Risk of danger to wildlife.
Warning!
Read the instruction manual.
Single value noise marking.
(Maximum declared
A-Weighted sound power level
in decibels).
11.1 EXPLANATION OF SYMBOLS
Warning!
Wear suitable foot protection.
Danger!
Risk of flying debris.
Warning!
Remove plug from power
supply before maintenance.
Warning!
Keep supply cord away from
cutting blade.
Danger!
Beware of sharp blades.
Warning!
Wear suitable eye/face protection.
- 18 -

- 19 -
12. DISPOSAL
12.1 DISPOSAL
– At the end of the machine’s working life, or when it can no longer be repaired, ensure that it is
disposed of according to national regulations.
– Contact your local authority for details of collection schemes in your area.
In all circumstances:
•Do not dispose of power tools with domestic waste.
•Do not incinerate.
•Do not abandon in the environment.
•Do not dispose of WEEE* as unsorted municipal waste.
* Waste Electrical & Electronic Equipment.

CONTACTS
– DRAPER TOOLS LIMITED,
Hursley Road, Chandler's Ford,
Eastleigh, Hampshire. SO53 1YF. U.K.
– Helpline: [phone]
– Sales Desk: [phone]
– Internet: www.drapertools.com
– E-mail: [email protected]
– Sales Fax: [phone]
– General Enquiries: [phone]
– Service/Warranty Repair Agent
For aftersales servicing or warranty repairs, please
contact the Draper Tools Helpline for details of an
agent in your local area.
YOUR DRAPER STOCKIST
RDCH0317
©Published by Draper Tools Limited.
No part of this publication may be reproduced, stored in a retrieval system or
transmitted in any form or by any means, electronic, mechanical photocopying,
recording or otherwise without prior permission in writing from Draper Tools Ltd.