DREAMS Sleigh Cot User manual

Sleigh Cot
30 minutes approx
assembly time
IMPORTANT, RETAIN FOR FUTURE REFERENCE:
READ CAREFULLY !
Two adult
assembly required
Product code
253-00152

Sleigh Cot - Assembly Guide - Page 2
Thank you
Hello, thanks for choosing to purchase your furniture from Dreams - you're now on your way to
creating a functional and fabulous room. Before you begin building your furniture, please take a
moment to read through the instructions and make sure that you've got all the relevant parts
listed on the following pages.
Assembly tips
Before you begin, it’s best to identify all parts and fittings to build your furniture.
We advise laying these out on the floor to check you have everything, and
familiarising yourself before building.
We recommend that you build your new furniture in the room you’d like it
to be located - this will help prevent any risk of damage to your newly
built furniture whilst moving it.
Top tip
Safety and care
It’s really important to ensure children and animals are kept away from the
assembly area, as there are small components used in this furniture which could
present a choking hazard. All plastic and wrapping materials should also be
To keep your little ones busy, there is a colouring page inside the back cover.
Help and support
At Dreams, it’s our mission to give the whole nation a great night’s sleep - this
means that the quality of our products is of utmost importance to us. If there
are any issues with your product or any missing parts, please visit our website
at www.dreams.co.uk/help
Recycling
Please ensure that packaging is disposed of in a safe and environmentally
friendly way, and recycle where possible. Our assembly instructions are
printed on recycled paper. Please keep your assembly instructions safe
to refer back to in the future.

Parts
1. Cot end x 2 pcs □
2. Mattress base x 1 pc □
3. Side rails x 2 pcs □
6. Drawer side left x 1 pc □
7. Drawer side right x 1 pc □
8. Drawer support x 1 pc □
Please check you have all the parts listed below with your product:
Do not discard any of the packaging until you have checked that you have all the parts and the pack of fixings.
Your child’s safety is your responsibility. Ensure that your child is kept clear during assembly due to small Parts.
Recommended mattress: 70 x 140 cm
This product complies with BS EN 716 - 1: 2017
Parts list
Important infomation
Sleigh Cot - Assembly Guide - Page 3
1 13
2 3 4
9 75
4. Drawer front x 1 pc □9. Drawer back x 1 pc □
6
8
5. Drawer bottom x 1 pc □

Fittings
Please check you have all the fittings listed below with your product:
0 1 2 3 4 5 6 7 8 9 1010 11 12 13 14 15 16 17 18 19cm
Tools required
Please check you have all these below:
Sleigh Cot - Assembly Guide - Page 4
Cross head
screwdriver
Bolt (M6x65mm) Barrel nut (M6x13mm) Bolt (M6x50mm) Screw (M4x30mm) Screw (M4x35mm)
Caster Screws
(M4x15mm)
Plastic barrel nut
(8x8mm)
Ax 4 B x 4 C x 12 D x 4 E x 4 F x 4
Gx 5 H x 10 I x 2
Bolt
(M4x25mm)
Allen key
Jx 4 K x 2
Bar handle
Flathead
screwdriver

21 22 23 24
Sleigh Cot assembly
Option 1
Sleigh Cot - Assembly Guide - Page 5
Option 2
Option 3

A
Sleigh Cot assembly
Use Pack 1 & 2
Sleigh Cot - Assembly Guide - Page 6
Attach Cot ends (1) to Mattress base (2) with Bolts (A), Barrel
nuts (C). Tighten the Bolts by using the Allen key (K) provided.
1
Option 1
Using a Cross head screwdriver (not provided) to adjust
and ensure the hole of Barrel nuts is facing out.
Do not fully tighten bolts at this stage.
Two adult
assembly required
A
A
x4
K
A
A
B
x4
2
1
1
2

Sleigh Cot assembly
Align and attach Side rails (3) to the Cot
ends (1) with Bolts (C).
Tighten the Bolts by using the Allen key.
2
Repeat the procedure to assemble the second
Side rails (3) to the Cot ends (1) with Bolts (C).
Tighten the Bolts by using the Allen key.
3
Use Pack 2
Sleigh Cot - Assembly Guide - Page 7
Do not fully tighten bolts at this stage.
Fully tighten all bolts once the assembly
is complete.
C
x6
1
1
3
C
C
C
C
3
C
C
C
C
C
C
x6
C

Drawer assembly
Align and attach Drawer side left (6) to the
Drawer front with Screws (D).
Tighten Screws by using the Cross head
screwdriver.
Ensure the Drawer bottom is inserted into
the slot of Drawer side left properly.
5
Use Pack 2
Sleigh Cot - Assembly Guide - Page 8
Align and insert Drawer bottom (5) into the slot
of Drawer front (4).
Align and attach Drawer side right (7) to the
Drawer front with Screws (D).
Tighten Screws by using the Cross head screwdriver.
Ensure the Drawer bottom is inserted in the
slot of Drawer side right properly.
4
6
4
5
6
D4
4
6
7
7
4
4
D

Drawer assembly
Align and attach Drawer support (8) to the slot
of the Drawer front.
7
Insert Plastic barrel nuts (F) into the holes
of the Drawer back (9).
Then, attach the Drawer back to both Drawer
sides with Screw (E), Plastic barrel nuts
Tighten Screws by using the Cross head
screwdriver.
Using a Flathead screwdriver (not provided)
to adjust and ensure the hole of Plastic barrel
nut is facing out.
8
Use Pack 2
Sleigh Cot - Assembly Guide - Page 9
8
8
4
9
8
9
F
E
E
F
x2
E
E
E
E

Drawer assembly
Align and attach Casters (G) to the Drawer
bottom, Drawer support with Screws (H).
Tighten Screws by using the Cross head
screwdriver.
9
Assemble Bar handles (I) to the Drawer front
with Bolts (J). Tighten the Bolts by using
the Cross head screwdriver.
10
Use Pack 2
Sleigh Cot - Assembly Guide - Page 10
x5
HH
G
5
I
J
J

Helpful Advices & Warnings
Please retain all instruction manual for future reference.
Always follow the manufacturer’s instruction. Failure to follow all of the instructions and warnings may cause injury.
Sleigh Cot - Assembly Guide - Page 11
Check all the Bolts, screws / parts and make
sure all Fittings must be tightened properly,
securely before use.
Warnings:
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Furniture can be dangerous if incorrectly installed. Assembly should be carried out by a competent person.
Keep children clear during assembly as pack contains small parts which may present a choking hazard.
Be aware of the risks of open fires and other such sources of strong heat, such as electric bar fires, gas fires, etc.
in the near vicinity of the cot.
Do not use the cot if any part is broken, torn or missing and use only spare parts approved by the manufacturer.
Do not leave anything in the cot or place the cot close to another product, which could provide a foothold or
present a danger of suffocation or strangulation, e.g. strings, blind/curtain cords, etc.
Do not stand on the cot before placing the mattress.
Do not use more than one mattress in the cot.
The lowest base position is the safest and should be used as soon as your baby is old enough to sit up.
The thickness of the mattress chosen must not reduce the internal depth (from the top of the mattress
surface to the top of the side) to less than 500mm with the base in its lowest position or 200mm with
the base in the highest position.
The mattress should be no more than 30mm shorter or narrower than the internal length or width
of the cotbed. Suitable for use with a mattress of 1400mm in length, 700mm in width and a maximum
thickness of 100mm.
All assembly fixings should always be tightened properly. Periodically check all fixings to ensure none
have come loose, and that there is no risk of clothing or parts of the body becoming snagged or trapped.
To prevent falls, when the child is able to climb out of the cot, the cot should no longer be used for that child.
Do not allow your child to jump on the cotbed. This may result in damage to the furniture and/or injury to your child.
Do not attach, stick or add any item to the inside or outside of your cot unless the item is specifically designed
to be used with a cot. Always follow safety instructions of items such as bumpers or cot mobiles that are
attached to cots if you choose to use them. Items that are added to cots could become a suffocation or
catch hazard for your baby.
Ventilation of the room is necessary in order to keep the humidity low and to prevent mould in and around the cot.
Dreams Limited
Knaves Beech, High Wycombe, Bucks HP10 9YU
https://www.dreams.co.uk

Sleigh Cot - Assembly Guide - Page 12
Care and maintenance
Here are some tips to keep your new furniture in tip-top condition
Cleaning
To clean your new furniture, we'd advise using a warm damp cloth - please do not
use abrasive chemicals or bleach as this may damage the product.
Fabric
Please note depending on the lighting, positioning and surroundings of your
period of time, the colour might lighten or fade slightly due to light exposure.
Wood
Please note each of our wooden pieces are unique, meaning that markings and
shade can vary slightly between beds. Over a period of time, the wood might
lighten or fade slightly due to light exposure.
Metal
Metal tends to be more resilient to everyday wear and tear. We recommend to
gently dust your metal furniture and keep it dry to maintain its look.
Periodically we recommend you check that the screws or fixtures haven't been
become loose, over time. To move your new furniture, we recommend lifting it where
possible, as dragging or pushing it could cause damage to your flooring.
Checking and moving
Thank you for shopping with us - we hope you have
a great night's sleep

Little dreamers
Keep the little ones entertained while
you assemble your new purchase.