DRIVEN DRWC4.3 Service manual

Installation Instructions | Owners Manual
Due to continuous improvement of the product, specifications are subject to change without notice.
DRWC4.3
TM
Wireless Reverse Camera Kit
Made in China

Congratulations on purchasing the Driven™ DRWC4.3 wireless reverse camera
system. This system uses the latest technology available to ensure that it is
durable, reliable and can provide a clear image of the view behind your vehicle
while reversing. This product uses the latest digital technology to ensure
durability and simple DIY installation.
SPECIFICATIONS
Monitor Type
Monitor Resolution
Wireless Range
Camera View Angle
Operating Voltage
Working Temperature
Weather Rating
4.3” Anti glare TFT-LCD
640 x 480
150 ft.
120* Horizontal
12/24V
-4* to +150*F
IP67
FEATURES
• 4.3” High Definition TFT LCD Monitor with Anti-glare Shade
• Weatherproof IP67 Reverse Camera with 120 Degree viewing Angle
• Wireless Camera Uses a Digital Signal that can be transmitted for
Long distances, Suitable for RV Vehicles
• 12/24V DC Power Supply

Please familiarize yourself with these instructions before starting your
installation.
The Monitor is equipped with a cigarette lighter plug that can be easily inserted
into the cigarette lighter socket in the vehicle.
MONITOR INSTALLATION
1) Find a suitable location on your dashboard or window screen for your
monitor. Please ensure it is in a location where it is easily viewable and
does not disturb your vision of the road while driving.
2) Clean the location that you have decided to place the monitor to
ensure that it is dust and grease free ( it is recommended to use alcohol
wipes to do this)
3) Mount the monitor base using the supplied suction cup.
STANDARD OPERATION
After the monitor and camera have been successfully installed and paired
(if required), turn the ignition key on ensuring the RED power button on
the monitor cigarette plug is switched on, View the image from the
camera on the monitor. If no image is visible, check all wiring connections
are securely fastened. If the image displays properly, please follow the
instructions below to adjust your screen settings:

Driven is a Registered Trademark of DB Research L.L.P. IDesigned and Engineered in the U.S.A.
WIRELESS CAMERA INSTALLATION INSTRUCTIONS
Thank you for your purchase of the DRIVEN DRWC4.3C wireless camera.
Proper installation of the Camera is critical to the overall view
you will be able to see from your in-cab DRIVEN DRWC4.3M wireless monitor. In
most cases the rear-view camera mount on an RVs is mounted just below the rear
top clearance lights. If your clearance lights are too low, this shouldn’t be a problem,
simply plan to for installation of the camera at the highest point of the rear outer
panel of your RV.
Most modern-day RVs are prewired with a 12v DC power supply cable that hidden
behind a camera mount cover. If this is the case, simply remove the 4 mounting
screws o the pre-mounted base , connect the simple 2 wire red and black cables to
the new harness and replace the complete mount and base with the DRIVEN
DRWC4.3C camera by screwing it down securely with the previously removed
screws.
In the event that your RV or trailer does not come prewired with a 12v DC power
supply at the desired location , you will have to carefully run a power supply cable
to the location on your RV were you wish to mount your camera system. Plan your
wire route for under the RV trailer . Be sure to avoid areas that could be aected by
heat or abrasion. Make sure to properly fuse the power supply cable at its origin.
Once the camera is powered up , follow the pairing instructions provided with the
DRIVEN DRWC4.3M wireless monitor. Align the camera and test the angle of the
view. Make sure to adjust the angle several times to check your options. Once you
have chosen the specic angle for the camera you are good to go.
POSITIVE 12V (RED)
NEGATIVE 12V (BLACK)
POSITIVE 12V (RED)
NEGATIVE 12V (BLACK)
CAMERATRAILER

ADJUSTMENT AND CAMERA PAIRING SETTINGS
K1: Brightness adjustment button. Press the K1 button to change the brightness of
the screen, as shown on the image below, press K1 to increase brightness, once
brightness bar reaches max keep pressing K1 to reset brightness to 1.
K2: Screen image flipping button. Pressing K2 will cycle the image left, right , up and
down to match the camera orientation (depends on how you mount the camera).
K3: Press once to enter camera pairing mode, the screen will display as shown below.
LIMITED WARRANTY
DrivenTM warrants any products purchased in the U.S.A. from an
authorized DrivenTM dealer.
All Products are warranted to be free from defects in material and
workmanship under normal use and service for a period of one (1) year.
This warranty applies to the original purchase only.
DrivenTM will either repair or replace (at its own discretion) any unit that
has been found to be defective and under warranty provided the defect
occurs within the one (1) year warranty period.
This limited warranty does not exted to units that have been subjected to
misuse, abuse, neglect, or accident. In Driven’sTM judgment, products that
show evidence of having been altered, modied, or serviced without
Driven’sTM authorization, will be ineligible under this warranty.
To Obtain warranty service please contact your retailer or visit our
website at www.drivenelectronics.com
After camera and monitor has been
successfully paired, hold the K3 button for
3 seconds to toggle reversing lines on the
screen. This is shown in the picture:
TM