Drone Sky Hook DSH-LSL1-MP Operating instructions

www.droneskyhook.com
Page 1 of 17
Drone-Sky-Hook LED SearchLight with Built-In Laser Pointer for DJI Mavic Pro/Pro Platinum
Model: DSH-LSL1-MP
Installation and Operation Guide
V1.0

www.droneskyhook.com
Page 2 of 17
Table of Contents
Overview 3
Overview of the LED SearchLight with Built-In Laser Pointer for DJI Mavic Pro and Mavic Pro Platinum 3
Applications 4
Applications for the LED SearchLight with Built-In Laser Pointer for DJI Mavic Pro and Mavic
Pro Platinum 4
Installation 5
Installation of Drone-Sky-Hook LED SearchLight with Built-In Laser Pointer for DJI Mavic Pro and
Mavic Pro Platinum 5
Operation 13
Battery Charging of the Drone-Sky-Hook LED SearchLight with Built-In Laser Pointer for DJI
Mavic Pro and Mavic Pro Platinum 13
Charging the SearchLight batteries during storage 13
Operation of the LED SearchLight with Built-In Laser Pointer for DJI Mavic Pro and Mavic Pro Platinum 14
Drone-Sky-Hook Release & Drop Device (PLUS models only) – Control Modes of the AUX Channel to
Turn the SearchLight On or Off 17
Note:
Additional information can be found in the Frequently Asked Questions page at the following
link: https://www.droneskyhook.com/frequently-asked-questions

www.droneskyhook.com
Page 3 of 17
Overview
Overview of the LED SearchLight with Built-In Laser Pointer for DJI Mavic Pro and
Mavic Pro Platinum
Revolutionary innovative design that perfectly fits your DJI Mavic Pro and Mavic Pro Platinum drones.
Combine the LED Searchlight with Built-In Laser Pointer with Drone-Sky-Hook Release & Drop PLUS devices to enhance
your DJI Drone night flight experience and see places in a different light at night!
Multiple Searchlight ON/OFF Control modes to best suit your application:
 Simple drone rotation (Self-contained. No linkage to the drone’s front LED light is required).
 Use of C1 or C2 button on the DJI drone remote controller or DJI App (Linkage to the drone’s front LED light is
provided).
 Manual control.
Connect-And-Fly in seconds! No modification of any kind to the drone is required! No tools needed!
Quick Mounting and Locking Systems (QMLS). Perfectly fit the DJI Mavic Pro and Mavic Pro Platinum drones.
Sensors Interference Avoidance System (SIAS). Will not interfere with the operation of the DJI Mavic Pro and Mavic Pro
Platinum VPS sensors.
Unlimited operation range.
Small and light weight. Weighs only 8 oz (230 grams) . Allows you to lift additional payload.
Can be rotated to shine its bright light forward, downward in angles or straight down. Illuminate your DJI drone takeoff /
landing area or other areas during your flight.
Over One hour of continuous operation on a single battery charge.
Built-in rechargeable battery and USB Charger. Can be charged from any 5V/1A mobile phone charger, USB jack on
computers/Laptops or car battery.
Robust design. High quality aluminum and 3D printed lightweight ABS.
Note: Do not overload your drone with heavy or bulky payloads that it cannot safely carry.

www.droneskyhook.com
Page 4 of 17
Applications
Applications for the LED SearchLight with Built-In Laser Pointer for DJI Mavic Pro and
Mavic Pro Platinum
Use the Quick Mount Drone-Sky-Hook Release & Drop PLUS combined with the LED Searchlight with Built-In Laser
Pointer to mark and illuminate points of interest on the ground.
Easily spot your DJI drone at night by using the Quick Mount Drone-Sky-Hook Release & Drop PLUS combined with the
LED Searchlight with Built-In Laser Pointer. Have a better view of your DJI drone’s position and orientation in the air under
low light conditions or total darkness. Use the Searchlight as landing light during takeoff and landing.
Fish at night with the Drone-Sky-Hook Release & Drop PLUS combined with the LED Searchlight with Built-In Laser
Pointer so you can lure the fish to the light while having a better view of your DJI drone’s position and orientation in the
air.
Search for a lost or missing person at night using the Quick Mount Drone-Sky-Hook Release & Drop PLUS combined with
the LED Searchlight with Built-In Laser Pointer. Enhance the view of your search area with this powerful searchlight that
shines bright light at night on objects as far as 330 feet (100 meter) away!
Before takeoff, rotate your LED Searchlight with Built-In Laser Pointer to shine its bright light forward, downward in angles
or straight down. Illuminate your DJI drone takeoff / landing area or other areas during your flight. This powerful
searchlight beam illuminates objects as far as 330 feet (100 meter) away!
Drone-Sky-Hook Release & Drop PLUS devices are required to control the LED Searchlight with Built-In Laser Pointer.
Drone Sky Hook strongly recommends that you follow all laws and regulations in your area, closely check your
surroundings prior to takeoff and keep away from civilians, properties, trees, buildings electric poles etc.
Drone Sky Hook shall not be responsible and assume no liability for any loss, damage or injury.
IMPORTANT NOTE: Do not overload your DJI drone with heavy or bulky payloads that it cannot safely carry.

www.droneskyhook.com
Page 5 of 17
Installation
Please click on the following links to watch the installation instructions videos:
Installing the Drone-Sky-Hook LED SearchLight with Laser Pointer for DJI Mavic Pro and Mavic Pro Platinum:
https://youtu.be/nOF0XaSzA5o
Installation of Drone-Sky-Hook LED SearchLight with Built-In Laser Pointer for DJI
Mavic Pro and Mavic Pro Platinum
Remove the original landing gear feet
Install the extended landing gear feet (provided)

www.droneskyhook.com
Page 6 of 17
Observe the correct orientation of the Release & Drop PLUS Device and insert it into the SearchLight
mounting plate as shown. The Release & Drop PLUS Device should tightly fit into the existing holes and
slots of the SearchLight mounting plate.
Correctly orient the Release & Drop PLUS Device with the SearchLight mounting plate as shown

www.droneskyhook.com
Page 7 of 17
Verify the correct installation of the Release & Drop PLUS Device on the SearchLight mounting plate as
shown. The Release & Drop PLUS Device should tightly fit into the existing holes and slots of the
SearchLight mounting plate.
Locate the SearchLight battery plug. It is a polarized connector with a locking tab. Observe the plug’s
orientation and plug it into the AUX jack on the Release & Drop PLUS Device. The plug should be locked
to the AUX jack.
Verify that the battery cable is away from the Drop Wheel as shown.

www.droneskyhook.com
Page 8 of 17
Remove the original landing gear feet that came with the Release & Drop PLUS Device
Install the extended landing gear feet (provided)

www.droneskyhook.com
Page 9 of 17
Slide the complete assembly (Release & Drop PLUS Device with the SearchLight) into the front slots
of the Mavic’s heatsink.
Spread the rear sides of the Release & Drop PLUS Device with your fingers and insert them into both
holes of the Mavic’s landing gear.

www.droneskyhook.com
Page 10 of 17
Lock down the Release & Drop PLUS Device rear rotating bracket until it locks in place
Lock down the coiled cable holder into the Release & Drop PLUS Device rear rotating bracket

www.droneskyhook.com
Page 11 of 17
Route the Light Sensor cable under the SearchLight mounting plate and orient the cable plug
towards its
j
ack located on the Release & Dro
p
PLUS Device.
Firmly plug the Light Sensor cable plug into
its jack located on the Release & Drop
PLUS Device. Verify that the plug is
inserted all the way into its jack.

www.droneskyhook.com
Page 12 of 17

www.droneskyhook.com
Page 13 of 17
Operation
Battery Charging of the Drone-Sky-Hook LED SearchLight with Built-In Laser Pointer
for DJI Mavic Pro and Mavic Pro Platinum
Charging
Plug the provided USB cable to the Searchlight batteries box. Connect the other end of this cable to a standard 5V / 1A
USB charger (like a mobile phone charger or other 5V / 1A charger. The specified charger output current should be no
less than 1A and no more than 2.1A).
Charge the Searchlight batteries overnight (12 hours) for maximum battery capacity. IMPORTANT: Disconnect it from the
charger after 12 hours.
Do not charge the batteries when the ambient temperature is below 32 degrees Fahrenheit (0 degrees Celsius) or above
104 degrees Fahrenheit (40 degrees Celsius).
Charging the SearchLight batteries during storage
Verify that the Searchlight is completely turned OFF and the Red light on its batteries box is OFF. This will prevent
continuous battery drain due to the Searchlight’s standby current.
To completely turn OFF the Searchlight and prevent continuous battery drain, verify that the AUX Channel is ON and then
turn OFF the Searchlight by pressing its pushbutton multiple times until the Red light on its batteries box turns OFF.
NOTE: The Searchlight draws standby current from its batteries even when the AUX Channel is OFF. Follow this
procedure to completely turn OFF the Searchlight and prevent continuous battery drain.
Charge the Searchlight batteries overnight (12 hours) every 4-6 months to maintain maximum battery capacity.
IMPORTANT: Disconnect it from the charger after 12 hours.
Do not charge the batteries when the ambient temperature is below 32 degrees Fahrenheit (0 degrees Celsius) or above
104 degrees Fahrenheit (40 degrees Celsius).

www.droneskyhook.com
Page 14 of 17
Operation
Please click on the following link to watch the use of the drone Remote Controller C1/C2 button to control and set the
Drop Wheel and Searchlight. These videos are applicable for Mavic Pro, Mavic Pro Platinum, Phantom 4 and Phantom 3
together with Drone Sky Hook Release & Drop PLUS models only and a SearchLight.
https://youtu.be/bG4lBDKNdKE
https://youtu.be/l9lDXQcLWKQ
Operation of the LED SearchLight with Built-In Laser Pointer for DJI Mavic Pro and
Mavic Pro Platinum
Connect the Searchlight to the AUX Channel jack on the Release and Drop PLUS device.
Turn ON the AUX Channel and then select the Searchlight desired light output mode by pressing the Searchlight
pushbutton multiple times.
When the Searchlight is turned ON, the Red light on its batteries box will be illuminated.
See operation video in the product support page.
At the end of the Searchlight operation you must completely turn OFF the Searchlight to prevent continuous battery drain.
Verify that the AUX Channel is ON and then turn OFF the Searchlight by pressing its pushbutton multiple times until the
Red light on its batteries box turns OFF.
NOTE: The Searchlight draws standby current from its batteries even when the AUX Channel is OFF. Follow this
procedure to completely turn OFF the Searchlight and prevent continuous battery drain.
Press the SearchLight
pushbutton to turn it On or
Off and to change the
SearchLight operation
modes.
Press the pushbutton
multiple times to select the
desired operation mode or
function.

www.droneskyhook.com
Page 15 of 17
SearchLight operation modes
Before takeoff loosen the rotation knob, rotate your LED Searchlight to the desired angle and tighten the rotation knob

www.droneskyhook.com
Page 16 of 17

www.droneskyhook.com
Page 17 of 17
Operation
Drone-Sky-Hook Release & Drop Device (PLUS models only) – Control Modes of the
AUX Channel to Turn the SearchLight On or Off
DSH Models: Single Release & Drop PLUS / Dual Release & Drop PLUS
Operation Mode 1 – Drone Rotation
Remote Controller (Mode 2)
LEFT STICK
Operation
Quickly Rotate (YAW) the drone two complete turns clockwise to command the AUX Channel to turn ON.
Quickly Rotate (YAW) the drone again two complete turns clockwise to command the AUX Channel to
turn OFF.
Operation Mode 2 – Drone Remote Controller C1/C2 Button and/or DJI App
Note: Use the DJI App to assign C1 or C2 button to Turn On/Off front LEDs
Remote Controller
C1 / C2 Button
Operation
Press C1 or C2 three times in quick succession (while maintaining about 0.5-1 second
between each press) to command the AUX Channel to turn ON.
Press C1 or C2 three times again in quick (while maintaining about 0.5-1 second between
each press) to command the AUX Channel to turn OFF.
DJI App Operation
Settings – Main Controller Settings – Advanced
Settings
In the App menu switch the drone’s front LEDs ON, then OFF and then back ON or OFF, then
ON and then OFF.
(Total of one ON-OFF-ON or OFF-ON-OFF cycle) to simulate the operation of the C1 or C2
buttons on the drone’s remote controller (see above).
Maintain about 0.5-1 second idle duration between each switch operation.
Operation Mode 3 – Manual – FUNC button on DSH unit
DSH Release & Drop unit Operation
Press three times the device’s FUNC button to simulate the operation of the C1 or C2 buttons
on the drone’s remote controller (see above).
Maintain about 0.5-1 second idle duration between each operation of the FUNC button.
IMPORTANT NOTE: At the end of each operation wait 3 seconds for the execution your command and before the initiation of the next command (False
Command Avoidance Algorithm (FCAA)).