DSC C24-CAM54IR User manual
C24ͲCAM54IR
QuickInstallationSheet
PackageContents
Thefollowingitemsshouldbeincluded:Ifanyof
theseitemsaredamagedormissing,pleasecontact
yourdistributorimmediately.
xC24-CAM54IR
xStand
xBlack Y-cable
xDC cable
xEthernet cable
xQuick Installation Guide
x12V 1A Power Adapter
ModelC24ͲCAM54IR
Dimensions72mm(W)x72mm(H)x20mm(D)
(withoutstand)
Operating
Temperature
Ͳ20qCto45qC
Video
compression
H.264,MPEG4andMJPEG
Network
Interface
1Ethernet10/100BaseT(RJ45)
Storage
Temperature
Ͳ20qCto60qC
LEDs3
PowerAdapter12V/1A
Front - C24-CAM54IR
1.IRLEDTheLEDscanhelpyouseeclearlyevenat
nightorinthedarkenvironment.
2.
Network
(Green)
xOn (Green)- LAN/Wireless
connection established.
xOff - No active connection on the
corresponding LAN port, or not
associated to Wireless AP
xFlashing - Data is being transmitted
or received.
3.
POWER/
WiFi
(Green)
xOn (Green)- Power On
xOff - Power Off
xBlinking - Data is being transmitted
or received.
xBlinking Low - Weak strength of
WiFi signal (1/2 Hz, SNR < 15 dB)
xBlinking Medium - Strength of WiFi
signal is normal (1/2 Hz, SNR < 15
dB)
xBlinking High - Good strength of
WiFi signal (1/2 Hz, SNR < 15 dB)
4.WPS
(Green)
xOn - When the WPS function is
failed, the WPS LED will be lit on
for 5 seconds.
xOff - WPS function is off.
xFlashing - WPS function is being
processed. If it is successful, the
WPS LED will be off.
Rear - C24-CAM54IR
1.LANPort
2.ResetThisbuttonhastwo(2)functions:
xReboot. When pressed and released, the
C24-CAM54IR will reboot (restart).
xClear All Data. This button can also be
used to clear ALL data and restore ALL
settings to the factory default values.
ToClearAllDataandrestorethefactorydefault
values:
1. Power On.
2. Keep holding the Reset Button down for 8
seconds.
ReleasetheResetButton.TheC24ͲCAM54IRis
nowusingthefactorydefaultvalues.
3.MicrophoneThebuiltͲinmicrophoneisusefulforbiͲdirection
voiceconversation.
UsestandardLANcable(RJ45connectors)to
connect tothe Customized
PoE(PoweroverEthernet)functiontoboth
Ethernet andAdapterissupported.
port.
the C24-HUB
Installation
Step 1 - Initial Setup
InitialsetupisrequiredwhentheC24ͲCAM54IRisusedfor
theFIRSTtimeconnectiontoaC24ͲHUB.Thisinitialsetup
willconfigurethecameraforprivateWiFioperation.
1. Assemble the Camera
a. Hold the metal screw of the stand up.
b. Thread the back of the C24-CAM54IR to the stand and
turn the C24-CAM54IR clockwise to attach it to the
stand.
2. Connect the Y-cable
Connect the provided Y-cable (with Ethernet) to the LAN
port of C24-CAM54IR.
The LAN interface is required for initial configuration.
After initial programming, the y-cable can be swapped
for the DC cable for WiFi operation.
3. Connect the Camera to the C24-HUB
Use the supplied Ethernet cable to connect the Y-cable
Ethernet port to the Device LAN port of C24-HUB.
4. Power Up the Camera
Connect the supplied power adapter to the Y-cable and power
up. Use only the power adapter provided. Using a different
one may cause hardware damage.
5. Check the LEDs
xThe Power LED will turn on briefly, then start blinking. It
will blink during startup, which takes 15 to 20 seconds. After
startup is completed, the Power LED should remain ON.
xThe Network LED should be ON.
Step 2 - Adding the Camera an the account
1.LogintoUserPortal(withauthorizedcredentials)
2.GotoSystemTab
3.Clickonthe“AddDevices”button
4.Clickon“Cameras”
5.SelectC24ͲCAM54IR
6.EntertheServerNameandclickon“Continue”
7.Clickon“Continue”
8.WaitwhiletheSystemaddsyourcamera
9.Clickon“Finish”tocompletetheinstallation.
RegulatoryApprovals
FCC Statement
Thisequipmentgenerates,usesandcanradiateradio
frequencyenergyand,ifnotinstalledandusedin
accordancewiththeinstructions,maycauseharmful
interferencetoradiocommunications.However,thereis
noguaranteethatinterferencewillnotoccurina
particularinstallation.Ifthisequipmentdoescause
harmfulinterferencetoradioortelevisionreception,
whichcanbedeterminedbyturningtheequipmentoff
andon,theuserisencouragedtotrytocorrectthe
interferencebyoneofthefollowingmeasures:
xReorient or relocate the receiving antenna.
xIncrease the separation between the equipment and receiver.
xConnect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
xConsult the dealer or an experienced radio/TV technician for
help.
Toassurecontinuedcompliance,anychangesor
modificationsnotexpresslyapprovedbytheparty
responsibleforcompliancecouldvoidtheuser'sauthority
tooperatethisequipment.(ExampleͲuseonlyshielded
interfacecableswhenconnectingtocomputeror
peripheraldevices).
FCC Radiation Exposure Statement
ThisequipmentcomplieswithFCCRFradiationexposure
limitssetforthforanuncontrolledenvironment.This
equipmentshouldbeinstalledandoperatedwitha
minimumdistanceof20centimetresbetweentheradiator
andyourbody.
ThisdevicecomplieswithPart15oftheFCCRules.
Operationissubjecttothefollowingtwoconditions:
(1)Thisdevicemaynotcauseharmfulinterference,and
(2)Thisdevicemustacceptanyinterferencereceived,
includinginterferencethatmaycauseundesiredoperation.
ThistransmittermustnotbecoͲlocatedoroperatingin
conjunctionwithanyotherantennaortransmitter.
CE Approvals
TheC24ͲCAM54IRandtheEthernetC24ͲCAM54IRmeet
theguidelinesoftheEuropeanUnionandcomplywiththe
99/5/EECandRTTE99/5EGdirectives,includingthe
followingstandards:
xEN60950
xEN300 328-2
xEN301 489-1
xEN301 489-17
ThisisaClassBproduct.Inadomesticenvironmentthis
productmaycauseradiointerferenceinwhichcasethe
usermayberequiredtotakeadequatemeasures.
ThisproductisULandcULcertifiedandcomplywith
UL60950Ͳ1InformationTechnologyEquipmentapplicable
requirement.
IC Approvals
ThisproductcomplieswithCanadianICESͲ003ClassB
andRSSͲ210.
Other DSC Security Camera manuals
