Digital Watchdog STAR-LIGHT Universal HD over Coax... User manual

Quick Start Guide Quick Start Guide
WHAT’S IN THE BOX
Hex Allen
wrench 1Mounting template 1
DC plug
cable 1
Screws
and plastic
anchors -
4pcs
1 set
Quick set up
guide 1
Moisture
absorber
and absorber
guide
1
1. The mounting surface must withstand five times the camera weight.
2. Pay attention to the cables. The can easily become caught and damaged.
Any damage may cause a short or fire.
3. Install the moisture absorber in the base of the camera’s lens.
a. Remove the moisture absorber from the packaging.
b. Cut the card and folder along the dotted line.
c. Place the moisture absorber behind the camera’s lens module. See drawing for more
information.
4. Detach the camera’s dome cover by loosening the four (4) screws on each side of the
dome.
5. Remove the dome protection film before placing the dome back on the camera base.
6. Using the mounting template sheet or the camera itself, mark and drill the necessary holes
in the wall or ceiling.
Pass the wires through the mount bracket and make all necessary connections. Connect the BNC cable and power cables to the camera.
STEP 1 – PREPARING TO MOUNT THE CAMERA
STEP 2 – CABLING THE CAMERA TO EXTERNAL DEVICES
Power Requirements Power Consumption
12VDC ON LY !
CAUTION! The camera supports DC power supply only
DC12V (LED o): 1.86W
DC12V (LED on): 3.6W
Tel: [phone]
Technical Support Hours:
9:00AM – 8:00PM EST, Monday through Friday
digital-watchdog.com
DWC-V6263TIR
Torx Wrench DC Plug Cable Test Video Cable
ManualTemplate Sheet Screw & Moisture absorber &
Absorber Guide
Sunshield cover &
Torx Wrench DC Plug Cable Test Video Cable
ManualTemplate Sheet Screw & Moisture absorber &
Absorber Guide
Sunshield cover &
Torx Wrench DC Plug Cable Test Video Cable
ManualTemplate Sheet Screw & Moisture absorber &
Absorber Guide
Sunshield cover &
Torx Wrench DC Plug Cable Test Video Cable
ManualTemplate Sheet Screw & Moisture absorber &
Absorber Guide
Sunshield cover &
Torx Wrench DC Plug Cable Test Video Cable
ManualTemplate Sheet Screw & Moisture absorber &
Absorber Guide
Sunshield cover &
Torx Wrench DC Plug Cable Test Video Cable
ManualTemplate Sheet Screw & Moisture absorber &
Absorber Guide
Sunshield cover &
Attention: This document is intended to serve as a quick reference for
initial set up. It is recommended that the user read the entire instruction
manual for complete and proper installation and usage.
NOTE: Download all your support materials and tools in one place.
1. Go to: http://www.digital-watchdog.com/resources.
2. Search your product by entering the part number in
the ‘Search by Product’ search bar. Results for
applicable part numbers will populate automatically
based on the part number you enter.
3. Click ‘Search’. All supported materials, including manuals
and quick start guide (QSGs) will appear in the results.
DW® Universal HD over Coax®
vandal dome cameras
Absorber attachment point
Please cut the card type absorber along
a dotted line, overlap and attach them
according to the direction of the arrow.
Protective film
Protective sheet
All manuals and user guides at all-guides.com
all-guides.com

U
Enter R
L
D
Right
Left
Up
Down
Quick Start Guide
1. The camera supports HD-Analog, HD-CVI and HD-TVI signals. To
switch between the signals:
a. Remove the camera’s dome to access the joystick and OSD
control on the base of the camera.
b. Use the OSD Switch to switch the camera’s signal.
- To switch the camera to HD-TVI mode, press OSD joystick to the
left for 5 seconds.
- To switch the camera to HD-Analog mode, press OSD joystick to
the right for 5 seconds.
- To switch the camera to CVBS mode, press OSD joystick
up for 5 seconds.
- To switch the camera to HD- CVI mode, press OSD joystick
down for 5 seconds.
1. Once all cables have been connected, use the screws included
with the camera to properly mount and secure the camera to the
mounting surface.
2. Adjust the camera’s pan, tilt and position to achieve the desired
view. The cameras’ max angles are:
Pan: 0° ~ 360°
Tilt: 0° ~ 90°
Rotation: 0° ~ 360°
3. To adjust the camera’s focus and zoom:
a. Unlock the zoom or focus screws by rotating them
counter-clockwise.
b. Adjust the zoom and focus screws at the base of the camera
module to achieve a clear image.
c. Tighten the screws and close the front case by rotating it
clock-wise.
4. Once the installation is complete, remove the protective film from
the camera’s dome cover.
STEP 4 – INSTALLING THE CAMERASTEP 3 – CHANGING THE SIGNAL IN
THE CAMERA
Rev Date: 09/19
Copyright © Digital Watchdog. All rights reserved.
Specifications and pricing are subject to change without notice.
HD-A
HD-TVI
CVBS(960H)
HD-CVI
U
Enter R
L
D
1
2
3
Test video slot
FOCUS
Focus: Far Near
Zoom: Wide Tele
ZOOM
OSD joystick controller
All manuals and user guides at all-guides.com