DSX Access System Lantronix UDS-1100 User manual

DSX Access Systems, Inc. 214-553-6140 www.dsxinc.com (10/2023)
®
Lantronix UDS-1100
KB2C Configuration
DSX Installation Guide
The Lantronix UDS-1100 is an ethernet to serial adapter that works with all DSX
Controllers. These instructions use Kb2cW.exe to program and configure the unit.
The UDS-1100 communicates RS-232 or RS-485 to the Controller based on
configuration and wiring.
Connect the Unit to a Desktop PC or Laptop for configuration by using the DSX-
DB25IB connector or supplied cable, connecting as shown to a DSX-USB. Use the
supplied power supply to power the unit while programming. After configuration, it
is powered from the DSX Controller or CDM through the same DB-25 connector.
Programming Connections
Comm Server
TX
RX
USB to PC
R S-232
To M a ste r
R S-485
To M a ste r
DSX-USB
DSXAccessSystems, Inc.
[phone]
TX RX DTR GND
TX + TX- R X + RX -
RS485 RS232
PW R
DSX-DB25IB
LANTRONIX
UD S11 00
PWR NET
Se ria l
TX+
TX-
RX+
RX-
TX
RX
GND
+12V
12 V
USE LANTRONIX
PO WER S U PPLY
FOR
CONFIGURING
UNIT
Wire this way to Configure the unit
Serial
RS232/422/485
UDS1100
9-30vdc
9-24vac
10/100
LANTRONIX
Power
10/100 Mb Link
10/100 Activity
Diagnostic
Status
UDS
Universal Device Server
13 1
25 14
BROWN
RED
BLUE
TEAL
WHITE/BLK
GREY/BL K
RED/BLK
BROW N/BL K
Comm Server
TX
RX
USB to PC
RS-232
To M a st e r
R S-485
To M a st e r
DSX-USB
DSXAccessSystems, Inc.
[phone]
TX RX DTR GND
TX + TX- R X + RX -
LANTRONIX
U DS11 00
PWR NET
Se ri a l
12 V
NOT USED FO R
CONFIGURING UNIT
USE LANTRONIX
PO WER S U PPL Y
FOR
CONFIGURING
UNIT
Wire this way to Configure the unit

DSX Access Systems, Inc. 214-553-6140 www.dsxinc.com (10/2023)
Programming Instructions
1. Disconnect power to the UDS1100.
2. Make the connections to the DSX-USB module.
3. Start KB2CW and select Comm Port / Define Port and enter the
port number the DSX-USB is connected to.
4. Caps Lock is OFF, Hold x on the keyboard, power up the unit.
5. After prompt, quickly press Enter for Setup Mode.
6. Type 0 to choose the ‘0 Server’ option.
7. Enter IP Address, pressing Enter after each octet.
8. Type Y to set Gateway IP Address.
9. Enter Gateway IP Address, pressing Enter after each octet.
10. Use Chart to the right to determine Netmask. Enter 8, 16 or 24.
11. Press Enter twice to accept the default <N> for the next two Netmask Chart
12. options. ClassA=24(255.0.0.0)
13. Type 1 to choose ‘Channel 1’ options. Class B = 16 (255.255.0.0
14. Press Enter to choose Baud 9600. Class C = 8 (255.255.255.3)
15. Set I/F Mode. RS-232 = 4C. RS-485 = 4D
16. Press Enter to accept Flow Control ‘00’ UDS-1100 Connections
17. Enter TX port number from the Comm Port in Database. To Master Controller
18. Connect Mode = CC
19. Datagram Type = 01
SendBroadcast=N
20. Remote IP Address = Comm Server Ip Address.
21. Typically, you press Enter to accept Remote Port <0>.
22. If both ports are defined in the software, they must both be
defined here. Mux requires both ports to be used and possibly
different.
23. Press Enter to accept the remaining defaults.
24. Press 9 to Save and Exit. Connect the unit to the controller.
All connections are made through the DB-25 connector to the controller.
See wiring info below:
Master Controller Communications
Db25 Color/Stripe Panel
2 Brown Tx
3 Red Rx
7 Blue Gnd
12 Teal +12V
14 Brown/Black Rx+
15 Red/Black Rx-
21 Grey/Black Tx+
22 White/Black Tx-
DB-25
at UDS1100
Connections
at DSX Panel
211514 22
RS-485 Terminations
Note /// Requires the
UDS1100
"I/F Mode" set to "4D"
RX+ RX- TX+ TX-
49 48 51 501022
55 56 53 541030 Series
712
GND +12v
BROWN/BLK
RED/BLK GREY/BLK
WHITE/BLK BLUE
TEAL
51 52 49 501021 & 1020
DB-25
at UDS1100
Connections
at DSX Panel
732
RS-232 Terminations
Note /// Requires the
UDS1100
"I/F Mode" set to "4C"
1042
TX RX GND
345
1043
1044
15 16 17
345
12
+12v
BROWN
RED BLUE
TEAL
1030 Series 49 50 51

DSX Access Systems, Inc. 214-553-6140 www.dsxinc.com (10/2023)
Master Controller Communications continued…..
485 IN
485 O UT
MA STER 485 IN
59
58
59
58
57
56
55
54
53
52
51
50
49
48
TX +
TX-
RX+
RX-
TX +
TX-
RX+
RX-
TX +
TX-
RX+
RX-
MASTER
1022
Controller
57
56
51
50
49
48
LANTRONIX
UDS11 00
PWR NET
Seria l
LANTRONIX
UDS1100
12
RX+
TX +
GND
+12v
7
14
15
21
22
RX-
TX-
GND
+12v TE AL
BLUE
BROWN/BLACK
RED/BLACK
GRE Y/ BLACK
WHIT E/ BLACK
485 IN
485 OUT
MASTER 4 85 IN
59
58
59
58
57
56
55
54
53
52
51
50
49
48
TX+
TX-
RX+
RX-
TX+
TX-
RX+
RX-
TX+
TX-
RX+
RX-
MASTER
1022
Controller
57
56
51
50
49
48
LANTRONIX
UDS1100
PWR NET
Serial
LANTRONIX
UDS1100
RS485 RS232
TX+
TX-
RX+
RX-
TX
RX
GND
+1 2V
DSX-DB25IB
PWR
USE READER PORT
FOR 12V AND GND
10 11 12 13 14 15 16 17 18 19 20 21 2212
TX RX
SUB
PW
LED1
D0
+12V
1A SIDE A INPUTS
34
TX RX
MASTER
6789
OUTP UTS
LED2
LED3 D1
GND
SIDE A READER
IN P 5
IN P 6
IN P 7
IN P 8
COM
OC
5
GND
A-1 A-2
MASTER
DSX-1042
LANTRONIX
UD S11 00
PWR NET
Se ria l
12 3 27
MASTER PANEL
ENCLOSURE
LANTRONIX
U DS11 00
RX
TX
GND
+12v
TE AL
BLUE
RED
BRO WN
10 11 12 13 14 15 16 17 18 19 20 21 2212
TX RX
SUB
PW
LED1
D0
+12V
1A SIDE A INPUTS
34
TX RX
MASTER
6789
OUTP UTS
LED2
LED3 D1
GND
SIDE A READER
IN P 5
IN P 6
IN P 7
IN P 8
COM
OC
5
GND
A-1 A-2
MASTER
DSX-1042
LANTRONIX
UD S11 00
PWR NET
Se ria l
MASTER PANEL
ENCLOSURE
LANTRONIX
U DS11 00
RS485 RS232
TX +
TX -
RX+
RX-
TX
RX
GND
+12V
DSX-DB25IB
PWR

DSX Access Systems, Inc. 214-553-6140 www.dsxinc.com (10/2023)
Sub Controller Communications
LANTRONIX
UDS11 00
PWR NET
Seria l
LANTRONIX
UDS1100
12
RX+
TX +
GND
+12v
7
14
15
21
22
RX-
TX-
GND
+12v
485 IN
485 O UT
MASTER 485 I N
59
58
59
58
57
56
55
54
53
52
51
50
49
48
TX +
TX-
RX+
RX-
TX +
TX-
RX+
RX-
TX +
TX-
RX+
RX-
SUB
1022
Controller
57
56
TE AL
BLUE
BROWN/BLACK
RED/BLACK
GREY/BLACK
WHIT E/BLA CK
485 IN
485 O UT
MASTER 485IN
59
58
59
58
57
56
55
54
53
52
51
50
49
48
TX +
TX-
RX+
RX-
TX +
TX-
RX+
RX-
TX +
TX-
RX+
RX-
SUB
1022
Controller
57
56
LANTRONIX
UDS1100
PWR NET
Se ria l
LANTRONIX
UDS1100
RS485 RS232
TX +
TX -
RX+
RX-
TX
RX
GND
+12V
DSX-DB25IB
PWR
USE RE ADER P OR T
FOR 1 2V AND GND
TO N EX T
ENCLOSURE
WITH SUBS
SUB PANEL
ENCLOSURE
910 1256712
TX RX
SUB
34
RX
811
MASTER
TX
INTERNAL COMM
TX + R X+TX - R X-
ABCD ABCD
1048TO 1048 COMM - WIRE OUT TO IN, TX TO RX or A-A, B-B, C-C, D-D
RX+ TX+RX- TX-
485 IN 485 O UT
DSX-1040CDM
J1
J2
SET J1& J2AS
"MA S" MAST ER IF
THEREIS A MASTER
CONTROLLER IN THIS
1048.
SET J1& J2 AS "SUB"
IF T H E R E IS N O T A
MASTER
CONTROLLER IN THIS
1048.
SUB MA S
12
TO SUB PANELS
IN ENCLOSURE
LANTRONIX
U DS11 00
PWR NET
Seria l
LANTRONIX
UD S11 00
12
RX+
TX +
GND
+12v
7
14
15
21
22
RX-
TX-
TE AL
BLUE
BRO WN/BLACK
RED/BLACK
GRE Y/BLA CK
WHIT E/ BLA CK
TO N EX T
ENCLOSURE
WITH SUBS
SUB PANEL
ENCLOSURE
910 1256712
TX RX
SUB
34
RX
811
MASTER
TX
INTERNAL COMM
TX + R X+TX - R X-
ABCD ABCD
1048TO 1048 COMM - WIRE OUT TO IN, TX TO RX or A-A, B-B, C-C, D-D
RX+ TX+RX- TX-
485 IN 485 O UT
DSX-1040CDM
J1
J2
SET J1& J2AS
"MA S" MAST ER IF
THEREIS A MASTER
CONTROLLER IN THIS
1048.
SET J1& J2 AS "SUB"
IF T H E R E IS N O T A
MASTER
CONTROLLER IN THIS
1048.
SUB MA S
12
TO SUB PANELS
IN ENCLOSURE
TO GND
TO +12V
RS485 RS232
TX +
TX-
RX+
RX-
TX
RX
GND
+12V
DSX-DB25IB
PWR
LANTRONIX
U DS11 00
PWR NET
Seria l
LANTRONIX
UD S11 00