DT Research Mobile POS Tablet User manual

WebDT Mobile Tablet Barcode Scanner Operation Guide
Mobile POS Tablet
Barcode Scanner
Installaon
The Barcode Scanner is preinstalled as an opon for WebDT 312/ 362.
Buon Management
To assign Scanner Trigger buon, follow the procedures below.
1. Start Buon Manager by clicking on in the system tray.
2. Click on to go to the second screen of Buon Manager.
3. Select an available unused buon marked with the icon .
4. Click on the icon to assign the Scanner Trigger to the
unused buon.
5. Click OK to apply conguraon sengs and close the
window.
Scanner Conguraon
To Add/Remove Symbologies, follow the procedures below.
1. Click Start | All Programs | DT Research | Buon Manager | ScannerCong.
2. Select COM3 and click Connect buon.
3. Add Symbology with buon and Remove Symbology with buon.
4. Select the Beep aer scanning barcode checkbox to enable beep sound aer
scanning bar code or deselect it to disable the beep sound.
5. Click OK to apply the conguraon sengs and close the window.
To Connect Barcode Scanner Module
To connect the Barcode Scanner, you can use the WebDT Keyboard
Wedge to connect. Tap on the icon in the task bar, a menu
displayed as shown in the picture below. Select Connect Scanner.
To Test Barcode Scanner Module
Click 1. Start | All Programs | Accessories | Notepad to run the Notepad
Scan one of the several supported barcode Symbology. The output will appear in the Notepad
2.
screen.
Verify the captured data.
3.
OPERATION GUIDE
www.dtresearch.com

WebDT Mobile Tablet Barcode Scanner Operation Guide
The Default Port Parameters for Barcode Scanner Module
SPECIFICATIONS
Electrical
Characteriscs
Voltage 3.3V+/- 5%
Current 370mA @3.3V scanning with power save
Idle 40mA
Standby current 3mA
Environment
Ambient light Works in any lighng condions,
from 0 to 100,000 lux
Shock 2000G, 0.7ms, half sinus, 3 axes
Vibraon 8G r.m.s., from 10Hz to 500Hz,
2 hours/axis, 3 axes
Interfaces High speed RS232 TTL with Intermec Scanner Control Protocol (ISCP)
Physical
Characteriscs
Scan engine
(H x W x D)
12.4 x 20.9 mm x 14.0 mm;
0.5 x 0.8 x 0.55 in
Decode board
(H x W x D)
6.6 x 38.1 x 25.4 mm;
0.25 x 1.5 x 1 in
Decoded 2D module
(H x W x D)
16 x 38.1 x 26.8 mm;
0.6 x 1.5 x 1.05 in
Weight 10g (0.35 oz.)
Scanning
Performance
Scan rate 2D mode: 56 images/s auto adapve
Linear emulaon mode: 200 scans/s auto adapve
Scan angle 38.9° (Horizontal), 25.4°(Vercal)
Opcal resoluon 752 (H) x 480 (V) pixels, 256 gray levels
Print contrast down to 25%
Versions Standard range and high density
Note: Specicaons are subject to change without noce.
www.dtresearch.com
signage dtri com
DT Research, Inc.
2000 Concourse Drive, San Jose, CA 95131 hp://www.dtresearch.com
Copyright © 2011, DT Research, Inc. All Rights Reserved.
DT Research and WebDT are registered trademarks of DT Research, Inc.
Linear Imager Compliance and Precauon
This product complies with the following standards for laser and LED safety.
IEC 60825-1 / EN 60825-1 - Class 1 LED Product
Port COM3
Baud Rate 57600
Data Bits 8
Parity None
Stop Bits 1
Flow Control None

WebDT Mobile Tablet Barcode Scanner Operation Guide
Mobile POS Tablet
CMOS Camera
OPERATION GUIDE
www.dtresearch.com
Installaon
The CMOS Camera is preinstalled as an opon for WebDT 312/ 362.
To Test CMOS Camera Module
To test the CMOS Camera, launch Microso® Paint from Start | All Programs | Accessories.
Select File | From Scanner or Camera to iniate the Capture Pictures from Video window.
Click Sengs to decide
properes of captured
pictures.
Click on Capture buon or
pre-assigned trigger buon
to take a picture.
Select a captured picture
on right column, click
Get Picture to export
the picture to Paint or
click Delete to delete the
picture.
4
4
4
Buon Management
To assign Camera Trigger buon, follow the procedures below.
1. Start Buon Manager by clicking on in the system tray.
2. Click on to go to the second screen of Buon
Manager.
3. Select an available unused buon marked with the icon .
4. Click on the icon to assign the Camera Trigger to the
unused buon.
5. Click OK to apply conguraon sengs and close the window.

WebDT Mobile Tablet Barcode Scanner Operation Guide
www.dtresearch.com
signage dtri com
DT Research, Inc.
2000 Concourse Drive, San Jose, CA 95131 hp://www.dtresearch.com
Copyright © 2011, DT Research, Inc. All Rights Reserved.
DT Research and WebDT are registered trademarks of DT Research, Inc.
SPECIFICATIONS
Sensor UXGA resoluon image sensor
Resoluon 640 x 480 (default),
1280 x 1024, 1600 x 1200, 2048 x 1536
LED Indicator Yes
Auto Focus Yes
Automac Image Control Automac exposure control
Automac white balance control
Focusing Type Auto focus
Focus Distance Focal on 60cm
Interface High speed USB 2.0
Regulatory RoHS compliant
Note: Specicaons are subject to change without noce.

WebDT Mobile Tablet Barcode Scanner Operation Guide
Mobile POS Tablet
Magnec Stripe Reader
OPERATION GUIDE
www.dtresearch.com
Installaon
The Magnec Stripe Reader (MSR) is preinstalled as an opon for
WebDT 312/ 362.
To Connect Magnec Stripe Reader Module
To connect the Magnec Stripe Reader, you can use the
WebDT Keyboard Wedge. Tap on the icon in the
task bar, a menu is displayed as shown in the picture
below. Choose Connect MSR.
To Congure MSR
For a magnec stripe card, the raw data in each data track may contain start and end sennel
characters. To remove those characters, you can select the Congure MSR command to parse input
raw data and lter out the start and end sennel characters on each track.
Click Cong MSR in the WebDT Keyboard Wedge menu, and the MSR Applicaon
1.
Conguraon window will be displayed.
Choose Enable in the Parse Data secon.
2.
Choose data you want to parse at the start or
end of each track.
For Example:
Check Track 1
In Start Sennel Character, select %
•
In End Sennel Character, select ?•
Click OK to complete the sengs3.

WebDT Mobile Tablet Barcode Scanner Operation Guide
www.dtresearch.com
signage dtri com
DT Research, Inc.
2000 Concourse Drive, San Jose, CA 95131 hp://www.dtresearch.com
Copyright © 2011, DT Research, Inc. All Rights Reserved.
DT Research and WebDT are registered trademarks of DT Research, Inc.
To Test Magnec Stripe Reader Module
Click 1. Start | All Programs | Accessories | Notepad to run the Notepad.
Swipe a magnec stripe card across the module. The output will appear in the
2. Notepad screen.
Verify the captured data.
3.
Default Port Parameters for Magnec Stripe Reader Module
SPECIFICATIONS
Reference Standards
ANSI/ISO Standards 7810, 7811-1/6, 7812 & 7813-
JIS X6301, X6302
-
AAMVA
-
Recording Method Two frequency coherent phase (F2F)
Decoding Method
ISO Track1: IATA, Track2: ABA, Track3: THRIFT
JIS: JISI-Tk1, TK2; JISII-Tk NTT
AAMVA
Card Swiping Direcon Bi-direconal
Card Swiping Speed Card speed through the unit may vary from 3ips to 100ips
(7cm/s to 250cm/s)
Life Electronics 125,000 hours
Head 1,000,000 passes
Note: Specicaons are subject to change without noce.
Port COM2
Baud Rate 19200
Data Bits 8
Parity None
Stop Bits 1
Flow Control None