dtec CONTROL V7E User manual

04/2022 - Version 1 DoorTec Deutschland | www.doortec.online
Änderungen vorbehalten | Subject to Modifications
OPERATION MANUAL
CONTROL V7E
VERSION 29.22

2 DoorTec Deutschland | www.doortec.online 04/2022 - Version 1
Änderungen vorbehalten | Subject to Modifications
2.4 Target group
Only qualified and trained service engineers shall in-
stall the control.
Only qualified and trained electricians shall connect
and carry out the electrical maintenance.
Qualified and trained professionals have knowledge of
the general and specific safety and accident preven-
tion regulations, of the relevant regulations and stand-
ards, training in the use and maintenance of adequate
safety equipment, as well as the ability to recognize
hazards associated with their work.
2.5 Key to symbols
1. CONTENTS
1. Contents ................................................... 2
2. General instructions ................................. 2
3. Safety related regulations ........................ 3
4. Safety instructions .................................... 3
5. Initial Operation ........................................ 4
6. LED Codes ............................................. 14
7. Run mode / error codes ......................... 15
8. Electronic counter and last 10 errors ..... 17
9. PCB-overview ........................................ 18
10. Connections ........................................... 19
11. Technical Data ....................................... 22
12. Declaration of conformity ....................... 23
2 GENERAL INSTRUCTIONS
2.1 Original operating instructions
• Copyright protection: any reproduction is permitted
only with permission of Tornado Antriebstechnik
GmbH.
• Changes in the interest of technical progress are
reserved.
• All dimensions are in millimetres, drawings are not
necessarily to scale.
2.2 Using the equipment for its intended purpose
The control V7E is designed only for controlling gates
and doors with mechanical or digital end position sys-
tems.
For other applications, the controller must be consult-
ed with the manufacturer.
2.3 Warranty
The function and safety of the equipment is only guar-
anteed if the warning and safety instructions included
in these operating instructions are adhered to.
The manufacturer is not liable for any personal injury
or damage to property that occurs as a result of the
warning and safety instructions being disregarded.
The CE declaration and warranty is voided by chang-
es such as unauthorized attachments, modifications or
rewiring goes out. Only original spare parts shall be
used.
These parts serve to maintain the quality and safety of
the machine. Changes are only permitted after consul-
tation with the manufacturer.
DANGER !
Safety notice indicating a danger that will directly result
in death or severe injury.
WARNING !
Safety notice indicating a danger that could result in
death or severe injury.
CAUTION !
Safety notice indicating a danger that could result in
slight or moderate injuries.
NOTICE !
Safety notice indicating a danger that could result in
damage to property or in irreparable damage to the
product
INFORMATION !
Reference to a check that needs to be carried out or to
separate documents that must be observed.

04/2022 - Version 1 DoorTec Deutschland | www.doortec.online 3
Änderungen vorbehalten | Subject to Modifications
3. SAFETY-RELATED REGULATIONS
For connecting, programming and servicing, the fol-
lowing regulations must be observed (the list is not
exhaustive).
• EN 12453 (Safety in use of power operated doors -
Requirements)
• EN 12445 (Safety in use of power operated doors -
Test methods)
• EN 12978 ((Industrial commercial and garage doors
and gates - safety devices for power operated doors
- Requirements and test methods)
References to additional, additionally accepted stand-
ards must also be observed, such as:
• EN 60204-1 (Safety of machinery, electrical equip-
ment of machines, part 1: general requirements)
• EN 12100-1 (Safety of machinery, basic concepts,
general principles for design. Basic terminology,
methodology)
• EN 60335-1 (Household and similar electrical appli-
ances - Safety)
• EN 60335-2-103 (Particular requirements for drives
for gates, doors and windows)
• Committee for Workplaces (ASTA)
• Workplace regulation ASR A1.7 (“Doors and gates“)
4. SAFETY INSTRUCTIONS
DANGER !
Failure to comply with the documentation could result in
life-threatening danger!
Be sure to follow all the safety instructions in this docu-
ment.
DANGER !
Life-threatening danger due to electric shock!
• It is vital that you disconnect the operator system
from the power supply before commencing cabling
work. Take measures to ensure that the power sup-
ply remains disconnected for the duration of the
work.
NOTICE !
For a three-phase current, a clockwise rotating field is
required.
WARNING !
• Ensure that children can not play with the door con-
trols or the hand transmitter.
• Before setting the door in motion, make sure that no
persons or objects are within the danger zone of the
door.
• Check all the existing emergency command devices.
• Pay attention to potential crushing and shearing
zones in the door system.
• Never touch a running door, the guide rail or any
moving parts.
INFORMATION !
For a permanent connection, an all-pole main switch
must be used.
WARNING !
• The control and the drive must be installed with its
intended covers and guards. It is important to en-
sure the correct fit of any seals and couplings are
tightened correctly.
• The mains voltage must correspond to the voltage
stated on the type plate.
• The mains voltage must be the same as the voltage
of the drive.
• For a three-phase connection, only 3-way automatic
circuit breakers (10A) may be used.
• Before switching on the controls for the first time, a
check must be carried out after completing the wir-
ing to ensure that all the motor connections at the
motor and at the controls are securely fixed.
• SAFETY RELAYS:
• If the control unit is a version without three safety
relays, the door manufacturer/installer is responsi-
ble of preventing any dangerous situation if one of
the contactors is welded.

4 DoorTec Deutschland | www.doortec.online 04/2022 - Version 1
Änderungen vorbehalten | Subject to Modifications
1. Select programming mode
To enter programming mode: Change DIL switch 1
(S4) to ON position.
Back to normal mode: Change DIL switch 1 (S4) to
OFF position.
2. Navigating the table
STOP push-button is used to navigate between pa-
rameter number and parameter value.
OPEN and CLOSE push-buttons is used to select pa-
rameter number or change parameter value.
Active digits will be flashing.
Some of the parameters have an extra step when
pressing the stop push-button. For example when the
door needs to run in programming stage. Display will
show ”RUN”.
3. Parameter explanation
5. INITIAL OPERATION
Before initial operation and at regular intervals of no
more than one year, power-operated windows, doors
and gates must be inspected by a qualified person
(whereby written inspection records must be kept).
After setting the system in operation, the operator of
the door system, or the operator’s representatives,
must be instructed in the operation of the system.
Make sure before installation that the direction of rota-
tion of the gear motor is correct and that all protective
devices are functioning.
5.1 Electrical installation
5.2 HOW TO program
The door will always run in hold-to-run mode when
programming. Program the control by opening the en-
closure. Find OPEN - CLOSE - STOP push-buttons
and a 4 pole DIL switch on the PCB (S4).
NOTICE !
To avoid damaging the device, the following must be
ensured:
• The cable types and cross-sections are to be chosen
according to the regulations.
• The rated currents and the connection type must
match those on the motor type plate.
• The on site fuse must comply with the specifications.
DANGER !
Life-threatening danger due to electric shock!
It is vital that you disconnect the operator system from
the power supply before commencing cabling work.
Take measures to ensure that the power supply re-
mains disconnected for the duration of the work.
NOTICE !
• The main power supply must be in the range of max.
+/- 10% of the control unit’s mains supply.
• Be sure not to overload the gear motor in accord-
ance with the electrical data on the type plate.
• Temperature control is necessary when using the
control outside the temperature range -10 - + 50°C.
• The control unit must not be used in environments
with risk of condensation.
Parameter value.
Parameter number.

04/2022 - Version 1 DoorTec Deutschland | www.doortec.online 5
Änderungen vorbehalten | Subject to Modifications
5.3 Parameter
Parameter overview
Parameter Description Page
Operation mode 7
Reaction – Failure on photo or Safety edge 7
Selection of limits 7
Learning - Electronic Limit Open 8
Fine Tuning of electronic Limit Open 8
Learning - Electronic limit CLOSE 8
Fine tuning of electronic limit CLOSE 9
½ Open settings 9
Auto close ½ open 10
Safety edge selection 10
After run 10
Extra safety edge 10
Wire tightening 11
Photo settings 11

6 DoorTec Deutschland | www.doortec.online 04/2022 - Version 1
Änderungen vorbehalten | Subject to Modifications
Parameter Description Page
Auto close 11
Car wash function 11
Forced closing 12
GO function (Step) 12
Interlock function ON/OFF 12
Run time control 12
Reverse time safety edge 12
Reserve time photo 13
Service counter setup 13
Service count reaction 13
Delay time indication of missing encoder position 13
Option relay K3 13

04/2022 - Version 1 DoorTec Deutschland | www.doortec.online 7
Änderungen vorbehalten | Subject to Modifications
The factory setting is shown in bold letters.
Parameter Value
Operation mode
01 = Hold to run OPEN
Hold to run CLOSE (bridge in terminal X3 / 23-24 when there is
no safety edge)
02 = Impulse OPEN
Hold to run CLOSE (bridge in terminal X3 / 23-24 when there is
no safety edge)
03 = Impulse OPEN
Impulse CLOSE
04 = Impulse OPEN
Impulse CLOSE
0,5 sec reverse by stop on force control in opening direction.
Notice: The door will always run in hold-to-run mode when programming.
Reaction – Failure on photo or
Safety edge
00 = Hold to run operation not possible when failure on photo or safety
edge.
The door cannot close when there is an error on photo or safety edge.
By a special code the door can close one time in hold to run mode.
Press and hold STOP when pressing 222111
(2 = DOWN push button and 1 = OP push button).
01 = Hold to run possible when failure on photo or safety edge.
Selection of Limits
00 = Mechanical Limits
01 = Dalmatic right turning
02 = Dalmatic left turning
03 = Feig TST PD right turning
04 = Feig TST PD left turning
05 = Kostal– right turning
06 = Kostal– left turning
Arrow = door opening
After changing to Kostal encoder a new power up is needed to start communi-
cation.

8 DoorTec Deutschland | www.doortec.online 04/2022 - Version 1
Änderungen vorbehalten | Subject to Modifications
Parameter Value
Learning - Electronic
limit OPEN
Press STOP 2 times - Display shows ‚run‘.
Run the door to open position. (By pressing OPEN or DOWN).
Press the STOP push-button to confirm open limit.
(The display will show open limit symbol about 2 sec. and the display will auto-
matic switch back to active parameter number).
Notice:
• ½ OPEN limit cannot be active during programming (parameter 16).
• Photo in the door frame (parameter 31) cannot be active during learning of
limits.
• When relearning limits parameter 41(force control) and 51(run time) will be
reset to factory setting.
Fine tuning of electronic
limit OPEN
Press STOP push-button until the display parameter value is active.
Fine tune OPEN limit 6-9 more open, 1-4 less open. Press OPEN or CLOSE
push-button to change value.
If the value is changed:
Press STOP push-button (Display shows ”RUN”)
Test the fine tuning by running the door up and down.
Press the STOP push-button to save and return to parameter value.
(adjustment range is maximum +/- 0.8% of the door run range)
Pressing STOP without a value change = return to parameter number.
Learning - Electronic limit
CLOSE
Press STOP 2 times - Display shows ‚run‘.
Run the door to close position (by pressing OPEN or DOWN). Normally 3-5 cm
from the floor.
Press the STOP push-button to confirm close limit.
(The display will show close limit symbol about 2 sec. and the display will auto-
matic switch back to active parameter number)
Notice:
• ½ OPEN limit cannot be active during programming (parameter 16).
• Photo in the door frame (parameter 31) cannot be active during learning of
limits.
• When relearning limits parameter 41 (force control) and 51 (run time) will be
reset to factory setting.
• The safety edge is not active during programming.

04/2022 - Version 1 DoorTec Deutschland | www.doortec.online 9
Änderungen vorbehalten | Subject to Modifications
Parameter Value
Fine tuning of electronic
limit CLOSE
Press STOP push-button until the display parameter value is active.
Fine tune OPEN limit 6-9 more open, 1-4 less open. Press OPEN or CLOSE
push-button to change value.
If the value is changed:
Press STOP push-button (Display shows ”RUN”)
Test the fine tuning by running the door up and down.
Press the STOP push-button to save and return to parameter value
(adjustment range is maximum +/- 0.8% of the door run range)
Pressing STOP without a value change = return to parameter number
½ Open settings
00 = No ½ open active.
Mechanical limit switches: (Value 00 in parameter 11)
01 = ½ open stop active.
Position controlled by mechanical micro switch (NC type)
in terminal 15 + 16.
Short-circuit terminal 15+16 parallel connected by mechanical
switch to ON/OFF this function.
Electronic limits: (Value > 00 selected in parameter 11)
ON/OFF controlled by switch in terminal X3,15+16
02 ½ open stop active. Electronic limit on 50 % open position.
03 ½ open stop active. Electronic limit on 55 % open position.
04 ½ open stop active. Electronic limit on 60 % open position.
05 ½ open stop active. Electronic limit on 65 % open position.
06 ½ open stop active. Electronic limit on 70 % open position.
07 ½ open stop active. Electronic limit on 75 % open position
½ OPEN command by a push button NO in terminal X3,15 + 16
08 ½ open stop active. Electronic limit on 50 % open position.
09 ½ open stop active. Electronic limit on 55 % open position.
10 ½ open stop active. Electronic limit on 60 % open position.
11 ½ open stop active. Electronic limit on 65 % open position.
12 ½ open stop active. Electronic limit on 70 % open position.
13 ½ open stop active. Electronic limit on 75 % open position

10 D DoorTec Deutschland | www.doortec.online 04/2022 - Version 1
Änderungen vorbehalten | Subject to Modifications
Parameter Value
Auto close ½ open
00 = No auto close from ½ open limit
01 = Auto close from ½ open limit
Notice:
Auto close must be activated in parameter 32.
Safety edge selection
Note that actual edge must be connected but not activated before this setup. If
the controller has observed a wrong edge select, the display will show ERR.
Please note that nothing must be connected to X3 terminal 23-24 when param-
eter value 03 have been chosen.
01 = NCC edge or DW switch AU contact
02 = 8k2 electrical edge
03 = optical edge (Type FRABA)
04 = DW switch (AG contact)
05 = Wireless safety edge with test function (X20)
After run
00 = No after run
> 00 After run active (after run time 0.01 – 0.50 sec.).
Monitoring of PNE/DW air switch safety edge is automatically selected when
after run is active. When the door reaches the close limit switch, the door will
continue to close until PNE/DW air switch activate or until the after run time
exceeds.
Notice:
Can be used to prevent that the door reverses when it reaches the floor before
the close limit gets activated – for instance if there is dirt in the door opening or
if the wires are getting longer.
Extra safety edge
(X20 – terminal 3-4)
00 = No extra safety edge
01 = Extra safety edge works parallel with primary safety edge
02 = Extra safety edge stops door in opening direction
03 = Stop and short reversal in opening direction
05 = Slack rope switch
06 = Slack rope switch (NC)