DTS SLICE PRO User manual

13000-30770-MAN (Rev. 3) © Diversified Technical Systems, Inc. - All Rights Reserved
SLICE PRO DIM
User’s Manual
March 2018

SLICE PRO DIM User’s Manual March 2018
support.dtsweb.com ii 13000-30770-MAN (Rev. 3)
TableofContents
DTS Support ....................................................................................................................... 3
Introducing the SLICE PRO DIM ....................................................................................... 4
Connector Panel................................................................................................................. 4
Using the Voltage Input.................................................................................................... 5
Using the Contact-Closure Input...................................................................................... 5
Electronic Identification (EID)........................................................................................... 5
Level Trigger.................................................................................................................... 5
Sampling Rates .................................................................................................................. 6
Data Memory Size............................................................................................................... 6
UP/DOWN Interface Connectors....................................................................................... 6
LEDs.................................................................................................................................... 7
Basic Care and Handling................................................................................................... 8
Shock Rating.................................................................................................................... 8
Mounting Considerations............................................................................................. 8
Thermal Considerations................................................................................................... 8
Power Management.......................................................................................................... 10
Power Consumption....................................................................................................... 10
Internal Battery............................................................................................................... 10
Power-up and Power-down Procedures ........................................................................ 11
Communication Features ................................................................................................ 11
Appendix A: LEMO Connector Information .................................................................. 12
Suggested Connector Sources...................................................................................... 12
Appendix B: UP/DOWN Connector Information ........................................................... 13
Appendix C: Mechanical Specifications........................................................................ 14
Accessories/Support Equipment.................................................................................... 15
Appendix D: How to Calculate Data Storage Duration................................................. 16
Circular Buffer Limitations.............................................................................................. 16
Appendix E: Declaration of CE Conformity .................................................................. 17

SLICE PRO DIM User’s Manual March 2018
support.dtsweb.com 313000-30770-MAN (Rev. 3)
DTS Support
TDAS systems are designed to be reliable and simple to operate. Should you need
assistance, DTS has support engineers worldwide with extensive product knowledge and
crash test experience to help via telephone, e-mail or on-site visits.
The best way to contact a DTS support engineer is to submit a request through the DTS Help
Center web portal (support.dtsweb.com). You must be registered
(support.dtsweb.com/registration) to submit a request (https://support.dtsweb.com/hc/en-
us/requests/new). Registration also enables access to additional self-help resources and
non-public support information.
This manual supports the following products:
13000-30770: SLICE PRO DIM (1B LEMOs) (18 ch)
13000-30771: SLICE PRO DIM (0B LEMOs) (18 ch)
13000-30772: SLICE PRO DIM (terminal blocks) (18 ch)

SLICE PRO DIM User’s Manual March 2018
support.dtsweb.com 413000-30770-MAN (Rev. 3)
Introducing the SLICE PRO DIM
The SLICE PRO Digital Input Module (DIM) is an 18-channel digital module capable of
recording virtually any on/off condition. Each channel is independently programmable for
either contact-closure or voltage event signals. The SLICE PRO DIM integrates with plug-
and-play ease into a SLICE PRO system and may be programmed for use as a level-trigger
for all modules in that system.
•Shock hardened to 100 g for dynamic testing environments.
•18 fully-isolated contact-closure or voltage event channels.
•Voltage event input range of 3-20 V.
•Electronic identification (EID) support. (Terminal block version does not support EID.)
•Internal battery with up to 1 hour capacity functions as primary or back-up power.
•LED indicators for power and system status.
•Easy communications via the SLICE PRO USB Controller or SLICE PRO Ethernet
Controller.
•Chainable with up to 3 other SLICE PRO modules.
Connector information and pin assignments are included in Appendices A and B. Mechanical
specifications are included in Appendix C. Appendix D provides information on how to
calculate data storage duration. Please see your packing list for your hardware’s
specifications.
Connector Panel
The SLICE PRO DIM is available with LEMO 0B, 1B or terminal block input connectors. See
Appendix A for connector information and pin assignments.
P/N 13000-30770 P/N 13000-30772
(0B LEMOs also available)
(images not to scale)

SLICE PRO DIM User’s Manual March 2018
support.dtsweb.com 513000-30770-MAN (Rev. 3)
Using the Voltage Input
These inputs are configured as shown below.
Operational Parameters
Voltage Input
Proper polarity must be observed.
>3 V = logic one (3-20 V input range with respect to chassis; logic
compatible).
Can be configured as normally high ( ) or normally low ( ).
Using the Contact-Closure Input
These inputs can be used 2 ways: simple contact closure or via an external semiconductor
switch.
Type of Contact Closure
Operational Parameters
Simple Contact Closure (tape
switch or other on/off device)
Self powered.
No polarity requirement.
Can be configured as normally open ( ) or
normally closed ( ).
External Semiconductor
Switch
=
Self powered.
Proper polarity must be observed.
<100 ohms = logic one; >4500 ohms = logic zero; with a
current conducting capability of at least 5 mA.
Can be configured as normally open ( ) or
normally closed ( ).
Electronic Identification (EID)
Each input channel supports communication with silicon serial number devices manufactured
by Dallas Semiconductor/Maxim Integrated Products. When an ID chip is connected to the
proper pins on the sensor connector, the software can read these devices and correlate the
serial number to channel set-up information stored in the sensor database. Note: The
terminal block version does not support EID. (See Appendix A for connector information and
pin assignments.)
Level Trigger
Any channel may be configured as a level-trigger channel via the software. When this
channel is triggered, all other modules in the SLICE PRO chain are also triggered. Specifying
a level-trigger channel does not prevent the SLICE PRO DIM from responding normally to a
hardware trigger.
C
E
+
-

SLICE PRO DIM User’s Manual March 2018
support.dtsweb.com 613000-30770-MAN (Rev. 3)
Sampling Rates
The SLICE PRO DIM has user-selectable sampling rates from 100 sps to 1 Msps. The
maximum sampling rate for 9 channels is 1 Msps; the maximum sampling rate for
18 channels is 500 ksps. Only 9 channels (channels 1-9 specifically) are available for any
sampling rate >500 ksps. For information on how to calculate data storage duration, please
see Appendix D.
Data Memory Size
With 15 GB of flash memory available for data storage, the SLICE PRO DIM can record
~14 minutes of data at the maximum sampling rate (9 channels at 1 Msps or 18 channels at
500 ksps). Since the recording capacity is very large, it is generally best to limit sampling
rates and event durations to the minimum necessary to avoid large and cumbersome data
files. Large files take longer to download and may also be time-consuming to post-process
or difficult to share. Use of the Region of Interest (ROI) download can save a great deal of
time if implemented properly. For information on how to calculate data storage duration,
please see Appendix D.
UP/DOWN Interface Connectors
The UP interface connector allows the user to interface to a SLICE PRO
Ethernet Controller, USB Controller or another SLICE PRO module. (The UP
connector may appear loose, however do not tighten.) The DOWN interface
connector allows the user to interface to another SLICE PRO module
(chainable with up to 3 other modules). Please see Appendix B for pin
assignments.

SLICE PRO DIM User’s Manual March 2018
support.dtsweb.com 713000-30770-MAN (Rev. 3)
LEDs
The SLICE PRO DIM has 2 LED indicators. At system power up, the red-green-blue LED
initialization sequence is performed by the status LED followed by the power LED.
LED behavior is summarized below.
Recorder Mode
Circular Buffer Mode
Armed and waiting for Start Record signal
to begin data collection
Start Record signal received and recording
data; waiting for Event signal (optional)
Armed and recording data;
waiting for Event signal
Event signal received (optional)
–or–fault
Event signal received
–or–fault
Event signal received + data collection
completed (no USB)
Event signal received + data
collection completed (no USB)
Fault received + data collection completed
(no USB)
Fault received + data collection
completed (no USB)
Data collection completed;
PC downloading data
Data collection completed;
PC downloading data
Condition
Charging (system off and connected to external power)
Unit is charging (power OK)
Unit fully charged
System on; not armed
Power up
. . .
Power OK; no USB
Power OK; USB connected
Power fault (out of range)
Communicating with host

SLICE PRO DIM User’s Manual March 2018
support.dtsweb.com 813000-30770-MAN (Rev. 3)
Basic Care and Handling
SLICE PRO systems are precision devices designed to operate reliably in dynamic testing
environments. Though resistant to many environmental conditions, care should be taken not
to subject the unit to harsh chemicals, submerge it in water, or drop it onto any hard surface.
WARNING:
Electronic equipment dropped from desk height onto a solid
floor may experience up to 10,000 g. Under these conditions,
damage to the exterior and/or interior of the unit is likely.
The SLICE PRO DIM is supplied with calibration data from the factory. DTS recommends
annual recalibration to ensure that the unit is performing within factory specifications. The
SLICE PRO DIM is not user-serviceable and should be returned to the factory for service or
repair.
When not in use or if shipping is required, we suggest that you always place the unit in the
padded carrying case originally provided with your unit.
Shock Rating
The SLICE PRO DIM is rated for 100 g, 12 ms half-sine duration, in all axes.
Mounting Considerations
The unit should be securely bolted to the test article or dynamic testing device to provide the
best shock protection. Mounting methods and hardware selection should be carefully
calculated to withstand expected shock loading and facilitate proper grounding. Check bolt
tightness periodically to ensure that 1) the unit is securely fastened to the baseplate, and 2)
the baseplate is securely fastened to the testing platform. (See Appendix C for the unit’s
mechanical specifications.)
DTS strongly recommends that all equipment be properly grounded to minimize any risk of
data noise due to high-current transients. The test vehicle or dynamic testing device should
be connected to earth ground. Crashworthy SLICE PRO equipment should be grounded to
each other and bolted to the test vehicle. SLICE PRO LAB modules should be bolted to the
rack and the rack properly grounded. DTS recommends checking continuity between the
enclosures of each unit to confirm resistance readings of <1 ohm.
Thermal Considerations
SLICE PRO systems are low power devices with negligible self-heating and it is unlikely that
self-heating will be an issue in real-world testing. Should you have anyquestions about using
SLICE PRO in your environment, please contact DTS.

SLICE PRO DIM User’s Manual March 2018
support.dtsweb.com 913000-30770-MAN (Rev. 3)
WARNING:
Due to battery chemistry, do not operate SLICE PRO DAS at
temperatures below 0°C (32°F) or in excess of 60°C (140°F).

SLICE PRO DIM User’s Manual March 2018
support.dtsweb.com 10 13000-30770-MAN (Rev. 3)
Power Management
A good power source is of paramount importance. SLICE PRO DIMs should be powered
from a SLICE PRO Controller. (One Controller can support up to 4 SLICE PRO modules.)
Be sure to consider any power drop due to cable length.
Input Voltage,
System OFF/ON
Power Consumption,
System OFF*
Power Consumption,
System ON**
11.5-15 VDC;
15 VDC nominal
7.5 W;
500 mA per module***
15 W;
1 A per module***
* charging all internal batteries ** fully armed + charging all internal batteries
*** Controllers are considered modules for the purposes of power calculations.
Power Consumption
Power off: When connected to sufficient external power, the SLICE PRO DIM will draw up
to 500 mA for charging the internal battery.
Power on: When the DIM is initially powered, all signal conditioning electronics are in a
shutdown state. When the user runs a test set-up, the software automatically energizes
these circuits. The current draw per DIM will increase to as much as 1 A when the system
is fully armed and energized.
During data collection: Once the system has been armed for data collection, all circuits
remain in a full power state until data collection is finished. After the data collection routine
has completed, the DIM de-energizes several circuits to minimize power consumption.
Internal Battery
The SLICE PRO DIM contains an internal 7.4 V (nominal) lithium battery that operates as
primary power or back-up power should primary power fail. When fully charged, battery
capacity is sufficient to provide primary power and sustain full operation for 1 hour. It charges
whenever sufficient external power is connected to the module via a SLICE PRO Controller.
The maximum charge time is 3-4 hours from complete discharge to full capacity. The module
does not need to be ON in order to charge the internal battery.
Charging practices can affect the useful operational life of the battery. In addition to good
charging habits, conditioning the battery may be useful—3 deep-discharge/recharge cycles
may increase battery performance. The battery’s useful capacity is greatly shortened near
the end of its service life and should be replaced when it has decreased to 50% of its initial
capacity. The batteryis not user-serviceable and should be returned to the factoryfor battery
replacement.
WARNING:
Due to battery chemistry, do not operate SLICE PRO DAS at
temperatures below 0°C (32°F) or in excess of 60°C (140°F).