DURAVAC CVQ810PF User manual

Wet/Dry Vacuum
Operator’s Manual
30 Liter
Model No.
CVQ810PF
FOR YOUR SAFETY
Read and understand this manual before use
Keep this manual for future reference
Part No. V
Q
71BZ.20.60.01
www.duravac.ca
Cleva North America
44 Parkway Commons
Greer, SC 29650 USA

2
SECTION PAGE
Thank you for purchasing this Dura Vac™ wet/dry vacuum cleaner. Feel confident that with
Dura Vac™ you are obtaining a high quality product engineered for optimal performance. This
vacuum is capable of picking up liquids and dry materials.
FOR YOUR SAFETY CAREFULLY READ AND UNDERSTAND ALL INSTRUCTIONS
We takes pride in producing a high quality, durable product. This Dura Vac™ product carries a limited two
(2) year warranty against defects in workmanship and materials from date of purchase under normal
household use. If product is to be used for commercial, industrial or rental use, a 90 day limited warranty
will apply. Warranty does not apply to defects due to direct or indirect abuse, negligence, misuse, accidents,
repairs or alterations and lack of maintenance. Please keep your receipt as proof of purchase. This
warranty gives you specific legal rights. For product service call Customer Service at 866- 384-8432
(Français 800-526-8563).
Warranty…………………………………………………………………………………………...…….
Safety Instructions and Warnings…………………………………………………………………….
Double insulation instructions…………..…………………………………………………………….
Extension Cord………………………………………………………………………………………….
Unpacking and Checking Carton Contents………….……………………..…………….………….
General Assembly Instructions…………………………………………………………….………….
Dry Vacuum Operation…………………………………………………………………………………
Wet Vacuum Operation………………………………………………………………………………..
Blowing Operation………………………………………………………………………………………
Maintenance……………………………………………………………………………….…………….
Installing & Cleaning Cartridge Filter……………………………...………………..….……………..
Installing & Cleaning Foam Sleeve Filter………………...………………….…..….………………..
Troubleshooting…………………………………………………………………………………………
Exploded View and Parts List………………………………………………………………………….
TABLE OF CONTENTS
WARRANTY
2
3
4
4
5
6
7
8
9
10
10
11
11
12

3
IMPORTANT SAFETY INSTRUCTIONS
READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE USING THIS VACUUM
Read and understand this owner’s manual and all labels on the Wet/Dry Vacuum cleaner before operating.
Safety is a combination of common sense, staying alert and knowing how your vacuum works. Use this
Wet/Dry Vac only as described in this manual. To reduce the risk of personal injury or damage to your
Wet/Dry Vac, use only Dura Vac™ recommended accessories.
Household Type
SAVE THIS MANUAL FOR FUTURE REFERENCE.
When using an electrical appliance, basic precautions should always be followed including the
following :
WARNING:TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY:
• Do not run vac unattended.
• Do not vacuum, or use this Wet/Dry Vac near flammable liquids, gases, or explosive vapors like gasoline
or other fuels, lighter fluids, cleaners, oil-based paints, natural gas, hydrogen, or explosive dusts like coal
dust, magnesium dust, grain dust, or gun power. Sparks inside the motor can ignite flammable vapors or
dust.
• Do not vacuum anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
• Keep cord away from heated surfaces.
• Do not expose to rain. Store indoors.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
• Do not use with damaged cord, plug or other parts.
• If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water,
return it to a service center.
• Do not pull or carry by cord, use cord as handle, close a door on cord, or pull cord around sharp edges or
corners.
• Do not run Wet/Dry Vac over cord.
• Do not handle plug or the Wet/Dry Vac with wet hands.
• To reduce the risk of health hazards from vapors or dusts, do not vacuum toxic materials.
• Do not use or store near hazardous materials.
• Do not use this Wet/Dry Vac with a torn filter or without the filter installed except when vacuuming liquids
as described in the operation section of this manual.
• Do not allow to be used as a toy. Close attention is necessary when used by or near children.
• To reduce the risk of injury from accidental starting, unplug power cord before changing or cleaning filter.
• Do not leave Wet/Dry Vac unattended when plugged in. Unplug from outlet when not in use and before
servicing.
• Turn off Wet/Dry Vac before unplugging.
• Do not put any object into ventilation openings. Do not vacuum with any ventilation openings blocked;
keep free of dust, lint, hair or anything that may reduce air flow.
• Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
• To reduce the risk of falls, use extra care when cleaning on stairs.
When using as blower:
• Direct air discharge only at work area.
• Do not use Wet/Dry Vac as a sprayer.
• Do not direct air at bystanders.
• Keep children away when blowing.
• Use safety goggles.
SAFETY INSTRUCTIONS & WARNINGS

4
This Wet/Dry Vac is double-insulated, eliminating the need for a separate grounding system. Use only
identical replacements parts. Read the instructions for Servicing Double-Insulated Wet/Dry Vacs before
servicing. Use this Wet/Dry Vac as described in this manual.
Observe the following warnings that appear on the motor housing of your Wet/Dry Vac.
DOUBLE INSULATED - GROUNDING NOT REQUIRED - WHEN SERVICING USE ONLY
IDENTICAL REPLACEMENT PARTS.
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK-DO NOT EXPOSE TO RAIN. STORE
INDOORS.
WARNING: FOR YOUR OWN SAFETY, READ AND UNDERSTAND OPERATOR’S MANUAL. DO NOT
RUN UNATTENDED. DO NOT PICK UP HOT ASHES, COALS, TOXIC, FLAMMABLE OR OTHER
HAZARDOUS MATERIALS, DO NOT USE AROUND EXPLOSIVE LIQUIDS OR VAPORS.
CAUTION:
• Do not vacuum drywall dust or fireplace soot or ash with standard Wet/Dry filter. This is a very fine dust
which will not be captured by the filter and may cause damage to motor. When vacuuming fine dust use a
fine dust filter (sold separately)
WARNING: SERVICING OF DOUBLE-INSULATED WET/DRY VACUUMM
WITH A DOUBLE-INSULATED WET/DRY VACUUM, TWO SYSTEMS OF INSULATION ARE PROVIDED
INSTEAD OF GROUNDING. NO GROUNDING MEANS IS PROVIDED ON A DOUBLE-INSULATED
APPLIANCE, NOR SHOULD A MEANS FOR GROUNDING BE ADDED. SERVICING A DOUBLE
INSULATED WET/DRY VACUUM REQUIRES EXTREME CARE AND KNOWLEDGE OF THE SYSTEM,
AND SHOULD BE DONE ONLY BY QUALIFIED SERVICE PERSONNEL. REPLACEMENT PARTS FOR
A DOUBLE-INSULATED WET/DRY VACUUM MUST BE IDENTICAL TO THE PARTS THEY REPLACE.
YOUR DOUBLE-INSULATED WET/DRY VAC IS MARKED WITH THE WORDS ‘DOUBLE INSULATED’
AND THE SYMBOL (SQUARE WITHIN A SQUARE) MAY ALSO BE MARKED ON THE
APPLIANCE.
• To reduce the risk of electric shock-unplug before cleaning or servicing.
• DO NOT use without filters in place.
CAUTION: TO REDUCE THE RISK OF INJURY FROM MOVING PARTS- UNPLUG BEFORE
SERVICING.
When using an extension cord with your Wet/Dry Vac refer to the following table to determine the required
A.W.G. wire size. Use only a 3-wire extension cord which has a 3-prong grounding type plug and 3-hole
receptacles which accept the tool’s plug. Before using the vacuum cleaner, make sure the power cord and
extension cord are in good working conditions. Make repairs or replacements before using the vacuum
cleaner. Only use extension cords that are rated for outdoor use.
Length of Extension Cord
110V-120V
25 Feet
7.5 Meter
50 Feet
15.25 Meters
100 Feet
30.5 Meters
150 Feet
45.7 Meters
Amps A.W.G Wire Size
0-6 18 16 16 14
7-10 18 16 14 12
11-12 16 16 14 12
13-16 14 12 Not recommended
EXTENSION CORDS
DOUBLE INSULATION INSTRUCTIONS

5
Remove entire contents of carton. Check
each item against the carton contents list.
Carton Contents List
Key Description……………………..…….…QTY
A Vac Assembly……………...……..
B Hose ……………………………....
C Floor Brush/Squeegee………..…
D 2-In-1 Utility Nozzle……….…..…
E Crevice Tool…………………...….
F Extension Wands....……….........
G Cartridge Filter ............................
H Filter Retainer………………...…..
I Foam Sleeve Filter……………....
J Foot With Caster……….…………
K Collection Bag………..…………..
L 6 Screws (Bag).……………….....
M Handle…………………………….
N Operator’s Manual……………….
UNPACKING AND CHECKING CARTON CONTENTS
1
1
1
1
1
2
1
1
1
4
1
1
1
1
NOTE: The hose and accessories for this vacuum
are 1.25 inch (3.2 cm) diameter.

6
A Philips head screwdriver is required for assembly.
WARNING: DO NOT PLUG IN POWER CORD TO POWER OUTLET, MAKE SURE PLUG IS
DISCONNECTED BEFORE ASSEMBLING THE WET/DRY VAC
UNPACKING YOUR WET/DRY VACUUM & GENERAL ASSEMBLY
1. Verify that the power cord is disconnected from the outlet. (fig.1)
2. Undo the latches. (fig.2)
3. Lift the power head off the container. (fig.3)
4. Remove the contents from inside the container, make sure you have all contents as listed on page 5.
(fig.4)
5. With the power head removed, turn the container upside down. Insert the feet with casters into the slots
and apply pressure into place and secure them with supplied screw. Do not over- tighten screws. (fig.5a)
6. Insert the handle into the slots located on the top of the power head and secure it with the screws
provided. Do not over tighten the screw. (fig.5b)
7. Your vacuum comes ready for dry vacuum cleaning with cartridge filter pre-installed. If cartridge filter is
not installed, refer to page 10 for filter installation. (fig.6 & 7)
8. Optional, for improved dust filtering, fit collection bag flange onto the vacuum port deflector, taking care
not to damage the bag. (fig.8)
9. For wet vacuum cleaning, install the supplied foam filter. (fig.9) See page 11 for filter installation.
10. Place the power head back on the container, and secure into place using the 2 side latches.
(fig.10 & 11)
11. Secure the large end of the hose into the vacuum port on the container and lock into place. (fig.12)
12. Choose the desired accessories and extension wands and push onto the suction tube. (fig.13)
GENERAL ASSEMBLY INSTRUCTIONS

7
POLARIZED PLUG
To reduce the risk of electrical shock, this appliance has a double polarized plug (one with the blade wider
than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet,
reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not
change the plug in any way. Double insulation eliminates the need for the three wire grounded power
cord and grounded power supply system.
DRY VACUUMING
WARNING: BE SURE TO READ, UNDERSTAND, AND APPLY INFORMATION, ENTITLED ‘SAFETY
INSTRUCTIONS & WARNINGS’. DO NOT VACUUM IN AREAS WITH FLAMMABLE GASES, VAPORS,
OR EXPLOSIVE DUSTS IN THE AIR. FLAMMABLE GASES OR VAPORS INCLUDE BUT ARE NOT
LIMITED TO; LIGHTER FLUID, SOLVENT TYPE CLEANERS, OIL-BASE PAINTS, GASOLINE,
ALCOHOL OR AEROSOL SPRAYS. EXPLOSIVE DUSTS INCLUDE BUT ARE NOT LIMITED TO;
COAL, MAGNESIUM, GRAIN OR GUN POWDER. TO REDUCE THE RISK OF HEALTH HAZARDS
FROM VAPORS OR DUST, DO NOT VACUUM TOXIC MATERIALS.
CAUTION:
• Do not vacuum drywall dust or fireplace soot or ash with standard cartridge filter. These are very fine dusts
which will not be completely captured by the filter and may cause damage to motor. When vacuuming fine
dusts use a fine dust filter (sold separately).
WARNING: DO NOT PLUG IN POWER CORD TO POWER OUTLET. MAKE SURE PLUG IS
DISCONNECTED BEFORE CHANGING AND CLEANING FILTERS.
1. Verify that the power cord is disconnected from the outlet. (fig.1)
2. In order to prepare your vacuum for dry vacuuming, verify that the cartridge filter is securely mounted.
With power head removed and in upside down position, make sure the filter is pushed in until it stops
against the power head and the retainer is installed. (fig.2 & 3) (Your Wet/Dry Vac comes with the
cartridge filter pre-installed, if not, see page 10 for installation instructions.)
3. Optional, for improved dust filtering, fit collection bag flange onto the inlet stub, taking care not to damage
the bag. (fig.4)
4. Place the power head back on the container, and secure it in place using the latches. (fig.5)
OPERATING INSTRUCTIONS: DRY VACUUMING
5. Insert the locking end of the hose into the vacuum port and screw in place. Push the required attachment
onto the free end of the hose or extension. (fig.6)
DRY-
V
ACUUM OPERATION

8
6. Plug in the power cord into the outlet. (fig.7)
7. Turn the motor on by flipping the switch to the ‘I’ ON position. (fig.8)
8. Once you have completed vacuuming, flip the switch to the ‘O’ OFF position and unplug the power cord
from the outlet.
O = OFF I = ON
DO NOT USE THE CARTRIDGE FILTER FOR LIQUID VACUUMING
DO NOT USE COLLECTION BAG FOR LIQUID VACUUMING
LIQUID VACUUMING
WARNING: BE SURE TO READ, UNDERSTAND, AND APPLY INFORMATION, ENTITLED ‘SAFETY
INSTRUCTIONS & WARNINGS’. DO NOT VACUUM IN AREAS WITH FLAMMABLE GASES, VAPORS,
OR EXPLOSIVE DUSTS IN THE AIR. FLAMMABLE GASES OR VAPORS INCLUDE BUT ARE NOT
LIMITED TO; LIGHTER FLUID, SOLVENT TYPE CLEANERS, OIL-BASE PAINTS, GASOLINE,
ALCOHOL OR AEROSOL SPRAYS. EXPLOSIVE DUSTS INCLUDE BUT ARE NOT LIMITED TO;
COAL, MAGNESIUM, GRAIN OR GUN POWDER. TO REDUCE THE RISK OF HEALTH HAZARDS
FROM VAPORS OR DUST, DO NOT VACUUM TOXIC MATERIALS.
WARNING: DO NOT PLUG IN POWER CORD TO POWER OUTLET. MAKE SURE PLUG IS
DISCONNECTED BEFORE CHANGING AND CLEANING FILTERS.
1. Verify that the power cord is disconnected from the outlet. (fig.1) Make sure that the container is clean
and free from dust and dirt.
2. Remove cartridge filter and collection bag, then carefully install the foam sleeve filter over the filter cage
and place the power head back on the container. (fig.2) See filter installing instructions on page 11.
DO NOT USE THE CARTRIDGE FILTER FOR LIQUID VACUUMING.
DO NOT USE COLLECTION BAG FOR LIQUID VACUUMING
OPERATING INSTRUCTIONS – WET VACUUMING
3. Fit the desired nozzle to the vacuum hose. (fig.3)
4. Verify that the switch is in the ‘O’ OFF position before plugging the power cord into the outlet. (fig.4)
5. Turn the motor on by flipping the switch to the ‘I’ ON position. (fig.5)
6. After use, empty the container by unscrewing the drain cap and drain liquids into suitable receptacle or
drain. (fig.6) Remember to refit the drain cap to the container after draining container.
IMPORTANT! When vacuuming large quantities of liquids, do not immerse the nozzle completely in the
liquid; leave a gap at the tip of the nozzle opening to allow air inflow. The machine is fitted with a float valve
that stops the suction action when the container reaches its maximum capacity. You will notice an increase
in motor speed. When this happens, turn off the machine, disconnect from power supply, and drain the
liquid into a suitable receptacle or drain. To continue vacuuming, refit the container with the drain cap. After
wet vacuuming, turn the machine off and remove plug from power supply. Empty the container, clean and
dry the inside and outside before storage.
WET-
V
ACUUM OPERATION

9
REMEMBER! The foam filter must be removed after wet vacuuming, and a cartridge filter must be
installed before dry vacuuming again.
This Wet/Dry Vac has blowing capabilities. To use the blower feature follow the instructions listed.
WARNING: ALWAYS WEAR SAFETY GOGGLES COMPLYING WITH ANSI Z87.1 (OR IN CANADA,
CSAZ94.3) BEFORE USING BLOWER.
WARNING: KEEP BYSTANDERS CLEAR FROM BLOWING DEBRIS.
WARNING: WEAR A DUST MASK IF BLOWING CREATES DUST THAT MIGHT BE INHALED.
1. Verify that the power cord is disconnected from the outlet. (fig.1)
2. Make sure the container is empty before using as a blower.
3. Remove hose from the vacuum port.
4. Insert the large end of the hose into the blowing port on the back side of the power head and secure it
into position. (fig.2)
5. Fit the desired extension wand and / or nozzle to the vacuum hose. (fig. 3)
6. Verify that the switch is in the ‘O’ OFF position before plugging the power cord into the outlet. (fig.4 & 5)
7. Before turning on the vac, firmly hold loose end of the hose. Turn the motor on by flipping the switch to
the ‘I’ ON position. (fig.6)
BLOWING OPERATION

10
WARNING: DO NOT PLUG IN POWER CORD TO POWER OUTLET. MAKE SURE PLUG IS
DISCONNECTED BEFORE CHANGING AND CLEANING FILTERS.
1. Verify that the power cord is disconnected from the outlet. (fig.1)
2. Disconnect the hose from the vacuum, turning large end in counter clockwise direction. (fig.2)
3. Undo the latches and remove the power head from the container. (fig.3)
4. Clear all dirt or debris from the container and hose. (fig.4)
5. Check the hose, attachments, and power cord to verify that they have not been damaged.
IMPORTANT! Clean or change the cartridge filter regularly for best performance. ALWAYS USE
CARTRIDGE FILTER FOR DRY VACUUMING. If the machine is used with out the cartridge filter, the
motor will burn out and the warranty will be voided. Always keep spare filters on-hand.
NOTICE! The filters included are made of high quality materials designed to stop small dust particles. The
cartridge filter should be used for dry pick-up only. A dry cartridge filter is necessary to pick up dust. If the
cartridge filter is wet, it will clog quickly and be very difficult to clean. Handle the filter carefully when
removing it for cleaning and replacing it. Check the filters for tears or small holes, a small hole can let dust
pass through and out of the cleaner. Do not use a filter with holes or tears in it. If filter is damaged, replace it
immediately.
WARNING! ALWAYS DISCONNECT THE PLUG FROM THE POWER OUTLET BEFORE REMOVING
THE POWER HEAD FROM CONTAINER.
Installing Cartridge Filter
1. Verify that the power cord is disconnected from the outlet. (fig.1)
2. Remove power head and place in upside down position.
3. Install the cartridge filter over the filter cage with the flat end of the filter towards the vacuum power head.
Carefully push filter in until it stops against the power head. (fig.2 & 3)
4. Place filter retainer on top of cartridge filter over the raise lip and tighten down by turning retainer
clockwise, do not over tighten. (fig.4 & 5)
MAINTEN
A
NCE
INSTALLING & CLEANING CARTRIDGE FILTERS

11
Removing and Cleaning Cartridge Filter
1. Unlock and remove the filter retainer by tuning retainer handle counter clockwise.
2. Carefully hold and pull the cartridge filter up for removal. (fig.6)
3. Clean the cartridge filter by gently tapping or brushing dirt off. Cleaning should not be done indoors in
living areas. For optimal performance a new filter is recommended.
4. Install cleaned or new filter into place as instructed above in steps 2 and 3 of Installing Cartridge Filter.
5. Wet filters should be removed and allowed to air dry for 24 hours before installing onto the filter cage.
Installing Foam Sleeve Filter
1. Verify that the power cord is disconnected from the outlet. (fig.1)
2. Remove power head and place in upside down position. Follow instructions to remove cartridge filter.
3. Carefully slide foam sleeve filter down over the filter cage making sure the whole cage is covered.
(fig.2 & 3)
4. Replace the power head on to the container.
Cleaning Foam Sleeve Filter
1. With the removed power head in the upside down position, carefully remove foam sleeve filter. (fig.4)
2. Use a mild soap and water solution to wash foam sleeve filter and rinse with clean water. (fig.5)
3. Allow filter to air dry before installing and using again.
Symptom Possible Causes Corrective Action
Vacuum will not operate 1) No power supply. 1) Check power supply – cord,
breakers, fuses.
2) Faulty power cord. 2) Unplug and check the power
cord. If damaged, have it repaired
by a professional.
3) Container full. 3) Empty container.
Dust comes out from motor cover. 1) The cartridge filter or collection
bag is missing or damaged.
1) Attach or replace cartridge filter
or collection bag.
Reduced efficiency and
motor/speed vibration.
1) There is a blockage in the nozzle
or hose, or the container inlet. Or
dust filter blocked by fine dust.
1) Check nozzle, hose and
container inlets for blockage. Take
off the filter and clean it. Or install
new cartridge filter.
T
ROUBLESHOOTING
INSTALLING & CLEANING FOAM SLEEVE FILTER
WARNING! TO REDUCE THE RISK OF ELECTRIC SHOCK-UNPLUG BEFORE TROUBLESHOOTING

12
PARTS LIST -EXPLODED VIEW