DURAVIT Vero VE 6414 User manual

Vero # VE 6414
Installation instructions
Leben im Bad
Living bathrooms
Instructions for use
The bathroom furniture range complies with the standards and guidelines applicable at the time of delivery and is designed for use in bathrooms.
Though designed for the wet environment, direct contact with water should be avoided, for example, when showering.
We reserve the right to make technical improvments and design modifications to the products illustrated.
MAL_Vero_VE6414/15.04.1
A A B B W W X X
mm inch mm inch mm inch mm inch
1000 39 3/8” 776 30 1/2” 130 5 1/8” 738 29”
# 032910
2x S8
2x 5,5x50 # UV 9991 # UV 9992
# F23628 # F30368 # 032985
2x 100
4x S8
4x5, 5x50

MAL_Vero_VE6414/15.04.1
123
Confirm that two legs are supplied,
install legs, facing front.
Mark the holes to be drilled for
the anchors.
Using 3/8“ dirll bit, drill the anchor
holes that have been marked.
The plastic anchors provided are
for concrete wall applications.
4 5 67
For wood stud walls bolts should
be screwed into wood backing.
Remove the vanity drawers. Push and lock in pins (1) and
remove the drawer. (2)
Attach the front legs.

MAL_Vero_VE6414/15.04.1
8910 11
Attach the back legs. Using the screwdriver, adjust the
vanity mounting hinge system
clockwise.
Using supplied key adjust leg
leveling.
Check the vanity is leveled.
12 13 14 15
Using the screwdriver, adjust the
mounting hinge system counter-
clockwise.
Screw two set screws until desired
leveling of the vanity has been
reached.
Using the appropriate bit for the
wall material, drill pilot holes.
The plastic anchors provided are
for concrete wall applications.

MAL_Vero_VE6414/15.04.1
16 17 18 19
For wood stud walls, bolts should
be screwed into wood backing.
Reference the washbasin
specification to establish the
position of mounting bolts, mark
the holes to be drilled for the
anchors.
Using the appropriate bit for the
wall material, drill pilot holes.
The plastic anchors provided are
for concrete wall applications.
20 21 22 23
For wood stud walls, bolts should
be screwed into wood backing.
When mounting the washbasin
into a wood stud wall, there must
be adequate bracing.
We recommend doubling up
2 x 6’s or 2 x 8’s between
the studs to form a solid
anchoring point.
Screw mounting bolts into the
pre drilled holes with an
adjustable wrench.
Screw in the full length of the
mounting bolt, so that the lag
thread is no longer visible.
Carefully slide washbasin onto
the mounting bolts. Insert the
white plastic sleeve over bolt and
into the hole in the washbasin.
Install provided washer and nut.
Hand tighten the nut, so the
washbasin is secure.
Install the siphon.
Close the drawer. Pull the drawer out.

MAL_Vero_VE6414/15.04.1
24 25 26 27
Install the vanity drawers.
Apply silicon bead between
washbasin and the wall.
Remove the plate. Level the vanity drawer by
adjusting two drawers.
Adjust the back of the drawer.
28 29
Adjust the drawer. Re-attach the plate.

MAL_Vero_VE6414/15.04.1
123
Confirm that two legs are supplied.
Leg installation facing sides.
Remove screws and re-attach
the plate.
Turn leg 90 degree and attach
the plate with supplied screws.
Attach front legs to the vanity.
4 5 67
Attach back legs to the vanity. Using the screwdriver adjust the
vanity mounting hinge system
clockwise.
Using supplied key adjust leg
leveling.
Check the vanity is leveled.

MAL_Vero_VE6414/15.04.1
8910 11
Using the screwdriver, adjust
vanity mounting hinge system
counter-clockwise.
Screw two set screws untill desired
leveling of the vanity has been
reached.
Using the appropriate bit for the
wall material, drill pilot holes.
The plastic anchors provided are
for concrete wall applications.
12 13 14 15
For wood stud walls bolts should
be screwed into wood backing.
Reference the washbasin
specification to establish the
position of mounting bolts.
Mark the holes to be drilled for
the anchors.
Using the appropriate bit for the
wall material, drill pilot hole.
The plastic anchors provided are
for concrete wall applications.

MAL_Vero_VE6414/15.04.1
16 17 18 19
For wood stud walls, bolts should
be screwed into wood backing.
When mounting the washbasin
into a wood stud wall, there
must be adequate bracing.
We recommend doubling up
2 x 6’s or 2 x 8’s between
the studs to form a solid
anchoring point.
Screw mounting bolts into the
pre drilled holes with an
adjustable wrench.
Screw in the full length of the
mounting bolt, so that the lag
thread is no longer visible.
Carefully slide washbasin onto
the mounting bolts. Insert
the white plastic sleeve over
bolt and into the hole in the
washbasin.
Install provided washer and nut.
Hand tighten the nut, so the
washbasin is secure.
Install the siphon.
Close the drawer. Pull the drawer out.
20 21 22 23
Install the vanity drawers.
Apply silicon beads between
washbasin and the wall.
Remove the plate. Level the vanity drawer by
adjusting two screws.
Adjsut the back of the drawer.

MAL_Vero_VE6414/15.04.1
24 25
Adjust the drawer. Re-attach the plate.

MAL_Vero_VE6414/15.04.1
Furniture complies with applicable requirements of the referenced standard(s):
Safety Household and Commercial Furnishings (UL 962, 3rd ed. Issued: 07/07/08, Revised: 08/05/13)
Portable Luminaires CSA C22.2 No. 12 - 1982 (R2004)
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical furnishing, basic precautions should always be followed, including the following:
Read all instructions before using this furnishing.
DANGER To reduce the risk of electric shock:
1. Always power down all circuits before cleaning.
WARNING To reduce the risk of burns, fire, electric shock, or injury to persons:
1.Disconnect from power before putting on or taking off parts. A minimum of two people is required to remove and
replace cabinet doors.
2. Close supervision is necessary when this furnishing is used by, or near children, invalids, or disabled persons.
3. Use this furnishing only for its intended use as described in these instructions. Do not use attachments not
recommended by the manufacture.
4. Never operate this furnishing if it has a damaged cord or plug, if it is not working properly, if it has been dropped
or damaged, or dropped into water. Return the furnishing to a service center for examination and repair.
5. Never drop or insert any object into any opening.
6. Do not use outdoors.
7. Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
8. For loading always put heavier items at the bottom and not near the top in order to help prevent the
possibility of the furnishing tipping over.
MAXIMUM SHELF LOAD IN POUNDS ALLOWED: 6.61 lbs
9. To disconnect, power down all circuits.
10. Risk of Injury to Persons - do not place video equipment such as televisions or computer monitors on
furnishing.
GROUNDING INSTRUCTIONS
This product must be connected to a grounded metal, permanent wiring system, or an equipment - grounding
conductor must be run with the circuit conductors and connected to the equipment grounding terminal or lead
on the product.
ABOUT THE PRODUCT
Products requiring electricity are designed to be switched at the wall and hardwired to a circuit provided by
the customer. Product should be installed according to electrical code by a qualified technician. Read important
safety instructions carefully. Direct wetting should be avoided. This products is intended for household/residential
use only. We reserve the right to make technical improvements and to enhance the appearance of the products
shown.
SAVE THESE INSTRUCTIONS