Dust Care DCC-2HD User manual

DCC-2HD
120V~
60Hz
1200W
5. Technical Specification
7
Instruction Manual
Voltage
Frequency
Power Input
Protection Class Class II
Max Vacuum
Noise
Please read manual carefully and keep
for
future reference.
R
RDivision of B.V.C. Smyrna,GA 30082
Push the HEPAfilter cover button,open the
cover and take out the HEPA filter for cleaning
or replacement.Re-installing the HEPA filter
is the reverse of the removal process.Be sure
to close the HEPA cover and make sure it is
sealed securely.
Caution:the HEPAfilter need to be cleaned or
replaced at least once a year.
Problem
Motor will
not start
Cause Solution
1.The plug isnot entirely plugged
into the socketor the socketdoes
not have electricity.
2.The switch isin the OFFposition.
Suction is low
1.The dust bagis full.
2.The filter,hose,brush etc, is
blocked.
1.Replace a newdust bag.
2.Clean the filter,hose,brush etc.
1.Re-insert the pluginto the socket
or try anothersocket.
2.Turn on the power switch.
4.trouble shooting
If the trouble still exists, please contact our maintenance service department.

1
Welcome to use our vacuum cleaner. You should read the manual before
operation to make sure safety. Please keep the manual properly for
reference later.
1.IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING
When using an electrical appliance, basic precautions should always
be followed, including the following:
WARNING To reduce the risk of fire, electric shock, or injury:
1.Do not leave appliance when plugged in. Unplug from outlet when not
in use and before servicing.
2.Do not use outdoors or on wet surfaces.
3.Do not allow to be used as a toy. Close attention is necessary when
use by or near children.
4.Use only as described in this manual. Use only manufacturer's
recommended attachments.
5.Do not use with damaged cord or plug. If the appliance is not working
as it should, has been dropped, damaged, left outdoors, or dropped into
water, return it to a service center.
6.Do not pull or carry by cord, use cord as a handle, close a door on cord,
or pull cord around sharp edges or corners. Do not run appliance over
cord. Keep cord away from heated surfaces.
7.Do not unplug by pulling on cord. To unplug,grasp the plug, not the cord.
8.Do not handle plug or appliance with wet hands.
9.Do not put any object into openings. Do not use with any opening
blocked, keep free of dust, lint, hair, and anything that may reduce air
flow.
10.Keep hair, loose clothing, fingers, and all parts of body away form
openings and moving parts.
11.Turn off all controls before unpluging.
12.Use extra care when cleaning on stairs.
13.Do not use to pick up flammable or combustible liquids, such as
gasoline, or use in arears where they may be present.
14.Do not pick up anything that is burning or smoking, such as cigarettes,
matches or hot ashes.
15.The power cord utilizes a special connector. If the cord has to be
repaired, you must go to a service center.
16.Do not use without dust bag and/or filters in place.
17.Connect to properly grounded outlet only. See Grounding Instructions.
When replacing the filter bag,open the dust
cover and remove the bag.Replace the bag
with an original factory supplied filter bag and
close the cover.You may then continue cleaning.
Caution:
1.Make sure the machine is completely turned
off before opening the cover.
2.Properly dispose of the dust bag.
B.Maintenance
Remove the filter from the bottom of the dust
cover and rinse out with water for cleaning.
Allow filter to completely dry and then place
back in the machine.
Caution:
1.The filter should be cleaned every 5-6 days,
of use or more if needed.
2.Do not operate with the dust bag removed.
3.Check to make sure the dust bag has been
installed correctly ant that there is no damage
to bag prior to use.
4.Make sure the machine is completely turned
off prior to removing the dust bag to ensure no
debris falls into the motor.
Caution:
1.The belt shoud be replaced if it is binding or
is not working properly.
2.The brush roll needs to be cleaned and free
of any debris or it will not work properly.
3.Make sure to unplug the machine prior to any
maintenance on the belt or brush roll.
To replace the belt and/or clean the brush roll
Remove the screw with a screwdriver and turn,
knob to remove the bottom plate and take out
the brush roll and belt for cleaning and
maintenance.
6

3.Dust empty and maintance
If the dust full indicator light is on(see arrow on
left),please replace with a new bag.
A.Dust empty
2
GROUNDING INSTRUCTIONS
This appliance must be grounded. If it should malfunctionally breakdown,
grounding provides a path of least resistance for electric current to reduce
the risk of electric shock. This appliance is equipped with a cord having
an equipment-grounding conductor and grounding plug. The plug must
be inserted into an appropriate outlet that is properly installed and
grounded in accordance with all local codes and ordinances.
WARNING Improperconnection of equipment-grounding conductor
can result a risk of electric shock. Check with a qualified electrician or
service person if you are in doubt as to whether the outlet is properly
grounded. Do not modify the plug provided with the appliance, if it will
not fit the outlet, have a proper outlet installed by a qualified electrician.
1)This appliance is for use on nominal 120-volt circuit, and has a
grounded plug that looks like the plug illustrated in sketch A in Figure 20.
A temporary adaptor that looks like the adaptor illustrated in sketch B
and C may be used to connect this plug to a 2-pole receptacle as shown
in sketch B if a proper grounded outlet is not available. The temporary
adaptor should be used only until a properly grounded outlet (sketch A)
can be installed by a qualified electrician. The green colored rigid ear,
plug, or the like extending from the adaptor must be connected to a
permanent ground such as a properly grounded outlet box cover.
Whenever the adaptor is used, it must be held in place by a metal screw
.
2)This appliance is for use on a nominal 120-volt circuit and has a
grounding attachment plug that looks like the plug illustrated in sketch
A in Figure 20. Make sure that the appliance is connected to an outlet
having the same configuration as the plug. No adaptor should be used
with this appliance.
For Commercial Use only
This machine has a 3-Position switch.Press
the switch backwards, and the vacuum will
start to operate. Press the switch forward to
turn on the vacuum and brush roll at the
same time. When the switch is in the middle
position the machine is OFF.
CAUTION: When the switch is in the forward
position, and the machine is left in the upright
position, a safety switch will automatically
cut the machine off.
Remove the hose from the main unit. Turn
on the switch and the hose can be used
separate from the machine. Use the
attachments included for various needs.
The Combination Nozzle can be used for
cleaning crevices, corners, baseboards,
etc. The Dust Brush can be used for furniture
or other surfaces.
STORAGE
Turn the machine OFF by moving the switch
to the middle position and remove the plug
from the outlet.
Return the machine to the upright position
and roll the cord around the cord hooks.
Replace the nozzle and the brush on the
handle.
CAUTION: Do not store the machine directly
in the sun or rain.
5

4
3
B.Operation guidance
Insert the dust bag into the bag housing.Make
sure it is inserted correctly(see figure on left).
Press the button on the hose cuff and take off
the connector.
Press the button of the dust cover as indicated
in the left figure.
Caution:This model is equipped with a safety
swith that won`t allow the machine to work
without a dust bag.
Remove the power cord and plug the machine
in to the outlet.Pull down on the handle and
turn on the machine at the power switch.
3 Hose
6 Bag housing
9 Handle
12 Wheel
15 Brush roll
2 Power switch
5 Dust cover
8 Quick release cord hook
11 HEPAfilter cover
14 Bottom plate release knob
17 Combination nozzle
1 Handle
4 Button of dust cup
7 Motorized brush
10 Lower cord hook
13 Bottom plate
16 Dust brush
2. Part name and operation
A. Part name