Dustless DustBull D1765 User manual

Saw Specic Instructions
DustBuddie Dust Shroud
for Flat Work
Model #D4000
Additional Products
7” DustBuddie XP
Model #D5850
7” CutBuddie
Model #D1750 5” DustBuddie
Model #D1835
1-3/8” BitBuddie
Model #D1900
Hepa Wet+Dry Dustless Vac
Model #D1603
6” Hose
For the Husqvarna K970 saw: remove the screws holding the rubber feet on.
Remove the rubber feet, set aside, do not discard. Install the Universal Mounting
Bracket by following the installation instruction on previous page. Use original screws
to install.
For Newer Stihl saw: with round rubber feet. Remove the screws in the bottom
front of the saw. Loosen the rubber feet and slide Universal Mounting Bracket under
the rubber feet. Align the holes in the bracket with the holes where you removed the
screws in the bottom of the saw. Tighten the rubber feet back down and use original
screw if possible to tighten down the bracket. If original screws do not t choose the
best screw from the included kit to secure bracket to the saw.
dustlesstools.com
PATENT NO. 5954863 & 5704956
Silica Compliance
The DustBull complies with OSHA’s Silica Rule when used in accordance with Dustless
Technologies’ objective data available for download on the DustBull product page at Dustlesstools.
com.

For cutting Block,
Brick, Pavers and
Rock with a gas
powered saw
OWNERS MANUAL
LIVE CUSTOMER SUPPORT & SERVICES:
1.800.568.3949 Toll-free in the U.S.
dustlesstools.com
Dust Shroud For Gas
High Speed Saws
Stops
Dust
Storms!
DustBull D1765 ts most gas highspeed saws!

WARNINGS
WARNING: Use of this product in conjunction with a gas powered saw will expose user to
harmful sicilia dust.
WARNING: Use of gas powered saw to cut concrete will create a large amount of silica dust.
Use of a respirator mask is recommended, especially in a non-ventilated area.
WARNING: This shroud is designed for hardscape work use only. It is intended for use when
cutting block, bricks, pavers or other types of hardscape material, not for use on Flat Work.
WARNING: Always use eye and ear protection when working with power tools.
WARNING: Always use the shroud only when properly installed and with properly running gas
powered saw.
WARNING: When dry-cutting concrete or stone products with a gas powered saw, OSHA
requires objective data conrming that a manufacturer’s solution is viable.
WARNING: This product may contain a chemical known to cause cancer, birth defects and
other harmfull side eects to a developing baby.
SUGGESTED USE
BEST USE: Always use this product with a vacuum that has at least 260 CFM.
BEST USE: For best results of dust collection, plunge blade into concrete and slowly work
forward making the cut.
BEST USE: Use product when dry cutting concrete. Will not work eectively when using
water to contain the dust.
BEST USE: Use the product in well ventilated area. This will help lessen the exposure to
harmful silica dust.
This shroud complies with OSHA Silica Rule Alternative Exposure Control Methods when
used in compliance with the third-party “Objective Data”available on our website. For more
information, go to www.dustlesstools.com or call us at 800-568-3949
SUGGESTED USE FOR BOLT KIT
IF POSSIBLE USE YOUR CURRENT SCREWS AND REINSERT AND TIGHTEN DOWN.
SILVER SCREWS: These Screws t most current and popular models of Stihl Gas Saws. Com-
pare the thread type of these screws to your original screw to insure correctness.
Choose the best length screw that ts your model saw. Make sure to tighten down till secure.
BLACK BOLTS: These bolts t most current and popular models of most other makes of gas
saws. Compare the thread type of these screws to your original screw to insure correctness.
Choose the best length bolt to t your make and model of saw. Make sure to tighten down
till secure.
OM019_0517
Warnings and Suggestions for use with Gas Saws

SETUP
SUPPORT
www.dustlesstools.com
1. Turn saw upside down. Remove screws
from the bottom front end of your saw
(circled Fig 1) (a wire brush may be
needed to clean out existing screw heads
for removal). *Dierent for each saw.
Screws will be located at the front of the
saw by the handle or the front feet.
2. Mount the Universal bracket on the saw
over the two holes where you just re-
moved the screws, with the tabs (circled
Fig 2) of the universal bracket facing to
the front and down away from the saw.
3. Align the holes in the saw with the holes
in the brackets, and reinstall the screws,
or use the included bolt kit to select the
proper length screw or bolt that will t.
Tighten down bolt or screw till secure.
Universal Bracket
Fig 2
Fig 1
*Check Saw Specic Instruction on back page if you have
questions about a specic saw.
Installation instructions for the Universal Bracket
4. Install the DustBull to your saw by lining
up the holes in the tabs of the Universal
Bracket and the holes in the bell of the
DustBull. Insert the 5.5” bolt and then
secure by inserting the included clevis pin
through the holes in the bolt.
5. Attach 2”vacuum hose to the back of
the DustBull when ready to cut. 2” hose
adaptor available at www.dustlesstools.
com or by calling customer service at
1-800-568-3949. Wrap the bungee around
the vacuum port to keep it out of the way
while cutting.
6. Only use Bungee to secure the back of
the DustBull to the saw for storage or
transporting. Wrap bungee a few times to
make sure bungee is tight.