DWG FE5403 User manual

Panoramic Fisheye IP Camera
8608595330000
Quick Installation Guide

Please follow the installation below steps to set up Panoramic Fisheye IP Camera.
Check the package contents against the list below.See P.1
Physical overview.See P.2
I/O Terminal Block Circuit.See P.3
I/O Terminal Block Pin Definition. See P.3
LED Indicator Definition. See P.4
Power mode. See P.4
Install the hardware and connect all cables.See P.4
Microsoft OS: Use the software CD to install Intelligent IP Installer.See P.7
Access the IP Camera using Intelligent IP Installer.See P.8
Mac OS using Safari Browser.See P.10
Change light environment setting. See P.11
Change the Web Interface into your preferred language.See P.11
For more information, please check the User Manual available in the Software CD
or you can download the latest software from http://www.champsolution.com
Package Contents
Note:
Power Adapter is supplied by user. 2pin I/O terminal block is for DC 12V Power
Adapter used.
Camera
Panoramic FisheyeIP Camera
Quick
Installation
Guide
Brief product information and quick installation
Software CD
IP Surveillance Software Intelligent IP Installer
User Manuals
Language Packs
Accessory
6 pin cable for DI/DO and audio
Screw pack for wall and ceiling mounting ( 2 screws, 2
plastic wall anchors )
Alignment sticker
L-type Hex Key Wrench
2pin I/O terminal block
Plastic plate for wall and ceiling mounting
1

Physical overview
Top cover
Ethernet Socket
Lens
MicroSD/SDHC
Reset
Power LED Indicator
Network LED Indicator
External I/O connector
DC 12V/1A
Routing hole
2

I/O Terminal Block Circuit
I/O Terminal Block Pin Definition
This Camera provides a 6pin cable for external I/O which is used to connect input/
output devices.The pin definitions are described below.
PIN Definition Description Max. V/A
Black Ground -
Brown + 12V DC 12V DC
1.2W
Red Audio
Input
Connect the wires of the audio input device
to GND (Pin 1) and AUDIO.IN (Pin 3).
-
Orange Audio
Output
Connect the wires of the audio output
device to GND (Pin 1) and AUDIO.OUT
(Pin 4).
-
Yellow Digital
Output 1
Uses an NPN transistor with the emitter
connected to the GND pin. If used with an
external relay, a diode must be connected in
parallel with the load for protection against
voltage transients.
100 mA
24V
Green Digital
Input 1
Connected to GND to activate, or leave
floating (or unconnected) to deactivate.
30V DC
3

LED Indicator Definition
LED Color Indication
Network
Blue Flash blue while Network activity.
Power
Red Steady red for booting up process
Blue Steady blue for booting up completion
Purple
Flash purple during firmware upgrading; when reset button
pressed for at least 5 sec. to factory default
Unlit When you press reset button; or Power off
Reset: When the device is empowered, press the Reset Button to reboot the
device, or hold the Reset Button for 10 seconds to the settings back to factory
default.
Reset process: Press reset button until indicator Unlitsteady red (booting up
process)steady blue (booting up completion)
Reset to default process: Press until indicator steady bluesteady red (booting
up process)steady blue (booting up completion)
Power Mode
PoE
Mode
Power Requirement
PoE (IEEE802.3af) with Class 3
Power Consumption 4.19W
Adaptor
Mode
Power Requirement
12V/1A Adaptor
Power Consumption 4.24W
Install the hardware and connect all cables
A.Hardware Installation
a. Loosen the tamper-proof screws using supplied L-type Hex Key Wrench
b. Remove the dome cover. Be careful do not scratch the cover glass.
c. If you want to route cable from the side of camera instead of routing hole,
please see below figure.
1. Attached the alignment sticker to the wall/ceiling. Drill three holes into the
wall, which two for screws and one for cable (if you want to route cables
through routing hole).
2. Align the two holes on the base of plastic plate with the two plastic anchors
on the wall or ceiling, insert the supplied screws to the corresponding hole
and fix them.
3. Secure the camera to the plastic plate with screws(M2.5x6 * 2pcs)
4. Adjust the angle of camera to aim the shooting area.
4

B.Wall mount L-type Bracket installation(optional)
1. Position the L-type at the desired installation location. Drill two holes into the
placement and hammer the included screw anchors.
2. Align the two holes on the L-type bracket to the two plastic anchors on the
wall or ceiling, insert the supplied screws to the corresponding hole and fix
them.
3. Secure the plastic plate to the L-type bracket with screws(M4x10 * 2pcs)
4. Secure the camera to the plastic plate with screws(M2.5x6 * 2pcs)
5. Adjust the angle of camera to aim the shooting area.
5

C. Wall mounting and Ceiling mounting
1. Attached the alignment sticker to the wall/ceiling. Drill three holes into the wall,
which two for screws and one for cable.
2. Hammer the supplied plastic anchors into the holes.
3. Align the two holes on the base of camera with the two plastic anchors on the
wall or ceiling, insert the supplied screws to the corresponding hole and screw
them.
6

D.Wall mounting and Ceiling mounting
f1. Without Power over Ethernet (PoE) connection
1. Connect the power adaptor to the IP Camera.
2. Connect the IP Camera to a normal Hub / Switch / Router.
f2. Power over Ethernet (PoE)
1. Connect the IP Camera to a PoE-enabled Hub / Switch / Router.
Note:
If using a non-PoE switch, please use a PoE power injector to connect the camera.
Microsoft OS:Use the software CD to install Intelligent IP Installer
1. Please go http://www.champsolution.com/DownloadMainpage.php download “Camera
Installation Tool”. Andfollow the installation process to complete the installation.
2. Select “Intelligent IP Installer” and follow the installation process to
complete the installation.
7

Access the IP Camera using Intelligent IP Installer
1. Please check two settings before using Intelligent IP Installer .
a. Browser’s Internet Properties
→
Security
b. Browser’s Internet Properties
→
Privacy→Uncheck Pop-up Blocker
2. Click the Intelligent IP Installer Icon on your desktop. The main page will
show up listing all active camera and video server devices. Select the
relevant IP camera from the list and click Link to IE.
3. Enter your Username and Password to login to the IP
Camera. (Default is admin / admin)
8

4. When accessing the IP Camera for the first time, a yellow information bar
appears below the address bar: This website wants to install the
following add-on: ‘AxvideoView.cab’.
5. Click the information bar, and select Install ActiveX control.
6. Click Install.
7. Live video displays in the centre of your web browser.
9