DXV Isle D35409000 User manual

- 1 -
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2017
INSTALLATION INSTRUCTIONS
In the United States:
DXV
One Centennial Avenue
Piscataway, New Jersey 08855
Attention: Director of Customer Care
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: [phone]
www.DXV.com
In Canada:
DXV
5900 Avebury Road
Mississauga, Ontario
L5R 3M3
Canada
Toll Free: 1-800-387-0369
Local: 905-306-1093
Fax: [phone]
www.DXV.ca
In Mexico:
DXV
Via Morelos 330
Col. Santa Clara Coatitla
Ecatepec, Estado de México 55540
Toll Free: 01-800-8391200
www.DXV.mx
SAVE FOR FUTURE USE
RECOMMENDED TOOLS AND MATERIALS
Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing
supply stores. It is essential that the tools and materials be on hand before work is begun.
ROUGHING-IN DIMENSIONS:
• For reference
M965573 Rev. 1.3 (4/17)
Model D35409000
Thank you for selecting DXV. To ensure that your
installation proceeds smoothly, please read these
instructions carefully before you begin.
Isle®
Single Lever
Kitchen Faucet
1-5/16" MAX.
(33.5 mm)
1-7/8"D.
(48 mm)
2" MAX.
(50 mm)
REINFORCED SUPPORT
6"
(152 mm)
3-1/4"
(83 mm)
7-5/8"
(193 mm)
9"
(229 mm)
13-5/8"
(346 mm)
19-11/16"
(510 mm)
1-1/4" D.
(32 mm)
3"
(75 mm)
3/8" (10 mm) COMPRESSION SUPPLIES
Adjustable Wrench Flat Blade Screwdriver
Channel Locks

- 2 -
1
2MAKE WATER SUPPLY CONNECTIONS
• Connect FLEXIBLE SUPPLIES (1, 2) directly to wall supplies.
• Connection on tting supplies are 3/8" (8 mm) compression. Connect
left SUPPLY (1) to Hot (Marked with a Red Stripe) and right supply to
COLD (2) wall supply (Marked with a Blue Stripe). Use adjustable
wrench to tighten connections. Do not over tighten.
• Faucet supplies are 20" (508 mm) long from faucet base.
Note: If additional supply length is required, installer must
purchase additional parts separately.
Important: If SUPPLY HOSES (1, 2) are to long, loop as
illustrated to avoid kinking.
• Seat SEAL (1) into under side of FAUCET BASE (2). Fig. A.
• Feed FAUCET SUPPLIES (3), and MOUNTING STUD (4)
through the mounting hole of mounting surface. Fig. A.
• From below, install SUPPORT PLATE (8), GASKET (7)
with RETAINING WASHER (5) onto MOUNTING STUD (4). Install
MOUNTING NUT (6) onto MOUNTING STUD (4).Fig. B.
• Adjust Faucet so that it is centered. Tighten MOUNTING NUT (6)
to complete faucet mounting. Fig. B.
INSTALL FAUCET
M965573 Rev. 1.3 (4/17)
APPROX. 20"
COLD
HOT
3/8" COMPRESSION
RED
BAND
BLUE
BAND
1
2
CAUTION Turn off hot and cold water
supplies before beginning.
8
4
1
GROOVE
(FAUCET
BASE)
Fig. A.
Fig. B.
6
4
7
5
3
2
MOUNTING
SURFACE

- 3 -- 3 -
3
4
TEST INSTALLED FAUCET
SERVICE
• With HANDLE (1) in OFF position, turn on WATER
SUPPLIES (2) and check all connections for leaks.
• Remove AERATOR (3).
• Operate HANDLE (1) to ush water lines thoroughly.
• Replace AERATOR (3).
Clogged CARTRIDGE outlets or inlets may cause reduced
flow. To clean, rst turn off water supply then:
• Pull out INDEX BUTTON (1). Loosen HANDLE SCREW (2)
with 2.5 mm Hex Wrench, then pull HANDLE (3) off.
• Unthread CARTRIDGE COVER (4) with CARTRIDGE RING
NUT KEY (7) supplied with faucet.
• Remove CARTRIDGE (5). Clean inlets of CARTRIDGE (5)
and MANIFOLD (6).
• Reassemble CARTRIDGE (5). Replace CARTRIDGE
COVER (4) and HANDLE (3) assembly, check ow.
• AERATOR (8) may accumulate dirt causing distorted
and reduced water ow. Remove AERATOR (8)
and rinse clean and replace.
M965573 Rev. 1.3 (4/17)
2
2
3
1
ON
COLD
HOT
OFF
REMOVE
LOOSEN
REMOVE REMOVE
8
2
1
5
4
7
3
6

- 4 -- 4 -
Replace the “YYY” with
appropriate finish code
POLISHED CHROME 100
ULTRA STEEL 355
MODEL NUMBER
D35409000
Isle®
Single Control
Kitchen Faucet
M965573 Rev. 1.3 (4/17)
M964508-0070A
CARTRIDGE COVER
NUT KEY
M964783-YYY0A
CARTRIDGE COVER
M964784-0070A
CARTRIDGE
M964782-YYY0A
HANDLE KIT
M964787-YYY0A
AERATOR KIT
M964827-0070A
SUPPORT PLATE
M964777-0070A
MOUNTING KIT
M964825-0070A
O-RING