DXV Percy D35105514 User manual

- 1 -
INSTALLATION INSTRUCTIONS
SAVE FOR FUTURE USE
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2017 M965629 Rev. 1.3 (5/17)
Cross Handle
Model D35105514
Cylinder Handle
Model D35105510
To be used with
D35000510.191 - 1/2"Thermostatic Mixing Valve
D35000530.191 - 3/4"Thermostatic Mixing Valve
Percy®
1/2"(13 mm) & 3/4"(19 mm)
Thermostatic Mixing Valve Trim Kit
Flat Blade ScrewdriverPhillips Screwdriver
FINISHED
FLOOR
FINISHED
WALL
1-11/16"
(44 mm)
to
2-1/2"
(64 mm)
5-7/8" (149 mm)
C
L
48" (1219 mm) TO
54" (1372 mm)
FOR SHOWER ONLY
(OPTIONAL)
32" (813 mm) TO
42" (1067 mm)
FOR BATH/SHOWER
AND BATH FILLER
(OPTIONAL)
3-3/8"
(86mm)
3-3/16"
(80 mm)
3" - 3-3/4"
(77 mm - 96 mm)
CROSS
HANDLE CYLINDER
HANDLE
1-7/16"
(36 mm)
1-7/16"
(36 mm)
7-5/16" DIA.
(185 mm)
2-1/2"
(63 mm)
RECOMMENDED TOOLS AND MATERIALS
Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing
supply stores. It is essential that the tools and materials be on hand before work is begun.
ROUGHING-IN DIMENSIONS:
• For reference
100
100
In the United States:
DXV
One Centennial Avenue
Piscataway, New Jersey 08855
Attention: Director of Customer Care
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: [phone]
www.DXV.com
In Canada:
DXV
5900 Avebury Road
Mississauga, Ontario
L5R 3M3
Canada
Toll Free: 1-800-387-0369
Local: 905-306-1093
Fax: [phone]
www.DXV.ca
In Mexico:
DXV
Via Morelos 330
Col. Santa Clara Coatitla
Ecatepec, Estado de México 55540
Toll Free: 01-800-8391200
www.DXV.mx
Thank you for selecting DXV. To ensure that your installation proceeds smoothly,
please read these instructions carefully before you begin.

- 2 - M965629 Rev. 1.3 (5/17)
1
2TRIM INSTALLATION
TEMPERATURE CALIBRATION
• Unscrew PLASTER GUARD SCREWS and remove PLASTER GUARD.
• Check that arrow marking “B” points vertically upwards. If not, push the BLACK CLAMP on the SECURING RING to
the right, pull off KNOB MOUNT and reinstall KNOB MOUNT with| arrow “B” pointing upwards.
• The maximum mixed water temperature is set at 109˚ F (43° C) at the factory. This setting can be changed if desired.
• Remove the TEMPERATURE LIMIT STOP (H shaped Black Plastic part). Re-install it at the desired notch as indicated in the
diagram to limit the maximum mixed water temperature to 104˚F or 112˚F.
• For 100˚F adjustment, turn the water supply on. Turn KNOB MOUNT until the spout temperature is 100˚F. Check that arrow
marking “A” on the KNOB MOUNT still points upward after adjusting the thermostat to 100˚F. If not, pull out the RED
LOCKING DEVICE. Remove KNOB MOUNT by pulling it towards you while standing directlyin front of the valve.
• Reinstall the KNOB MOUNT so that the arrow marking “A” points upwards.
• Reinstall RED LOCKING DEVICE.
KNOB
MOUNT
ARROW
"A"
BLACK
CLAMP
ARROW
"B"
RED LOCKING
DEVICE
SECURING
RING
TEMPERATURE
LIMIT STOP 104°F
(40°C)
109°F
(43°C)
112°F
(44.4°C)
• Push CAP (1) over the O-RING SEAL (2).
• Push ESCUTCHEON HOLDER and SEAL (3) with lightly greased O-ring seal over CAP (1).
• Align PINS (4) on back side of ESCUTCHEON (5) with the TWO HOLES (6) in ESCUTCHEON HOLDER (3)
and press ESCUTCHEON (5) ush against nished wall.
• Align ESCUTCHEON MOUNTING HOLES (7) with valve body in wall and secure with MOUNTING SCREWS (8).
2
1
6
6
3
GREASE
ESCUTCHEON
HOLDER
O-RING SEAL
4
5
8
7

- 3 - M965629 Rev. 1.3 (5/17)
3
4
HANDLE INSTALLATION
OPERATING THE VALVE
TRANSPOSED SUPPLY PIPING
Should the hot and cold water supply pipes have been transposed
making adjustment impossible, proceed as follow:
• Shut off water supply.
• Remove handle and rim.
• Remove check stops and re-install them transposed.
• Important note: RED CHECK STOP is now on the right of
the mixer body and the BLUE CHECK STOP is now on the left.
• Turn the water supply back on and perform the temperature
adjustment in step one.
5
ROLL
PIN
100
2
7
3
4
6
5
1
9
8
10
CHECK STOP
(RED TO BLUE)
CHECK STOP
(BLUE TO RED)
• Push DIAL PLATE (1) onto CAP (2) until ush against ESCUTCHEON.
• Push TEMPERATURE CONTROL KNOB (3) onto KNOB MOUNT (4). Attach TEMPERATURE CONTROL KNOB (3)
to valve with ATTACHMENT SCREW (5).
• Push HANDLE BASE (6) onto TEMPERATURE CONTROL KNOB (3). Tighten set screw with HEX WRENCH (7)
to secure HANDLE BASE (6).
• Align HANDLE (8, 9) with roll pin and install onto HANDLE BASE (6). Tighten set screw with HEX WRENCH (10)
to secure HANDLE BASE (6).
100
2
1
• Rotate handle counter-clockwise from cold to the maximum hot
temperature desired that was preselected in step one.
• If a temperature over 100°F is desired, push the STOP
BUTTON (1) down and turn the TEMPERATURE KNOB (2).
This will increase the mixed water temperature up to the
maximum limit previously selected in step one.

Percy®
1/2"(13 mm) & 3/4"(19 mm)
Thermostatic Mixing Valve
Shower Trim
M965629 Rev. 1.3 (5/17)
- 4 -
Replace the “YYY” with
appropriate finish code
POLISHED CHROME 100
CARBON BRONZE 110
Cross Handle
D35105514
Cylinder Handle
D35105510
100
M964650-0070A
TRIM PLATE HOLDER
M964649-YYY0A
TRIM PLATE
WITH SCREWS
H960004.191
HANDLE ADAPTER
M964653-YYY0A
COVER
M964651-YYY0A
CROSS
HANDLE KIT
M964652-YYY0A
CYLINDER
HANDLE KIT
H961235.XXX
DIAL PLATE
A860826.191
ESCUTCHEON SCREWS
H960892.191
HANDLE EXTENSION KIT
M964813-0070A
SET SCREW KIT
M964618-0070A
SET SCREW KIT