DXV Victorian D35402400 User manual

- 1 -
INSTALLATION INSTRUCTIONS
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2017
In the United States:
DXV
One Centennial Avenue
Piscataway, New Jersey 08855
Attention: Director of Customer Care
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: [phone]
www.DXV.com
In Canada:
DXV
5900 Avebury Road
Mississauga, Ontario
L5R 3M3
Canada
Toll Free: 1-800-387-0369
Local: 905-306-1093
Fax: [phone]
www.DXV.ca
In Mexico:
DXV
Via Morelos 330
Col. Santa Clara Coatitla
Ecatepec, Estado de México 55540
Toll Free: 01-800-8391200
www.DXV.mx
SAVE FOR FUTURE USE
Thank you for selecting DXV. To ensure that your
installation proceeds smoothly, please read these
instructions carefully before you begin.
RECOMMENDED TOOLS AND MATERIALS
Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing
supply stores. It is essential that the tools and materials be on hand before work has begun.
M965537 Rev. 1.2 (4/17)
Model D35402400
Victorian
Single Control Bar Faucet
ROUGHING-IN DIMENSIONS:
• For reference
Plumbers' Putty or CaulkingAdjustable Wrench
Phillips Screwdriver
Channel Locks Flat Blade Screwdriver
7-15/32"
(190mm)
10-3/4"
(273mm)
2-3/4"
5-1/2"
(140mm)
2-1/4"D.
(57mm)
3/8" COMP
NOTE: Bore hole size is 1-3/8"
21"
(533mm)
2-3/16"
(53.8mm)

- 2 - M965537 Rev. 1.2 (4/17)
1
• Make certain the O-RING (2) is properly seated in recess of FAUCET BASE (3).
• Insert HOSE (9), SHANK (10) through center hole of sink or mounting surface.
• Assemble three BRASS SCREW (8) into the FIXATION RING (7).
• Assemble SUPPORT PLATE (5) METAL WASHER (6), and FIXATION RING (7) onto SHANK (10) from underside of sink.
Hand tighten the FIXATION RING (7) and check that FAUCET (1) is centered.
• Use a screwdriver to tighten SCREW (8) on FIXATION RING (7). Work your way around FIXATION RING (7),
tightening the screws slightly each time until all are snug to ensure even pressure.
INSTALL FITTING
CAUTION Turn off hot and cold water
supplies before beginning.
1
3
2
4
8
9
6
5
10
7

- 3 - M965537 Rev. 1.2 (4/17)
2
3TEST INSTALLED FAUCET
• Move HANDLE (1) into “off” position.
• Turn on water supplies and check all connections for leaks.
TROUBLE SHOOTING
Low water flow from faucet:
• Remove AERATOR (2) and clean if necessary.
MAKE WATER SUPPLY CONNECTIONS
• Turn off hot and cold water supplies before beginning.
• Connect FLEXIBLE SUPPLIES (1, 2) directly
to wall supplies. Connection on tting
supplies are 3/8" compression. Connect
left supply (Marked Red) to Hot and right supply
(Marked Blue) to Cold wall supply. Use adjustable
wrench to tighten connections. Do not over tighten.
Faucet supplies are 21" long from faucet base.
Note: If additional supply length is required,
installer must purchase additional parts separately.
Important: If SUPPLY HOSES (1, 2) are too long, loop
as illustrated to avoid kinking.
SUPPLY STOPS
1
2
1
2

- 4 -
Replace the “YYY” with
appropriate finish code
POLISHED CHROME 100
CARBON BRONZE 110
ULTRA STEEL 355
MODEL NUMBER
D35402400
Victorian
Single Control
Bar Faucet
M965537 Rev. 1.2 (4/17)
M964741-0070A
SPOUT SET SCREW
H962078.191
CARTRIDGE NUT
H961342.XXX
HANDLE KIT
H962019.XXX
HANDLE FIXATION
M964406-0070A
CARTRIDGE
M964667-0070A
MOUNTING KIT
M964670-0070A
SWING SPOUT SEAL KIT
H960567.XXX
AERATOR
M964669-YYY0A
ESCUTCHEON KIT
M964668-YYY0A
DECORATIVE RING KIT