Dyconn SylvanTrinidad User manual

Product Features:
Modern design faucets
Water saving control
Lower power consumption
Intelligent sensor control
Stable & Reliable
Sensor Faucet Manual
Models: HF1H21-ORB (Sylvan), HF1H21-CHR (Trinidad)
HF1H22-CHR (Heath), HF1H22-BN (Lawa)
HF1H23-CHR (Nelson), HF1H23-BN (Peace), (HF1H23-ORB) Snake
- Thoroughly read all instructions before installing the enclosed faucet.
-Read and understand all warnings, care and maintenance information
For easy installation of your Dyconn Faucet please do the following:

Product Description & Information
OPERATION AND MAINTENANCE.
PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE FOR PRODUCT
Do not place or install the product directly under the sun or long exposure of
sunlight
Do not place any catoptric items such as mirror to the opposite wall of the
inductive window.
CAREFULLY READ THIS INSTRUCTION MANUAL BEFORE INSTALLING AND USING
Do not use contaminated water with the device.
Do not soak the device in water, this will cause permanent damage.
Product Description & Information
Features:
Specification:
Water saving control - sensor responds to object approach in 0.5s and stops
once object leave sensor range.
Sanitation - automatic sensor keeps hand free of touching faucet
Intelligent sensor - Faucet will automatically stop if water flows over 1 minute.
Sensor resets in 10s. Faucet stops working if water supply or power is out to
minimize water leakage.
Low power consumption - 4 AA batteries can be consumed for 2 years 300 cycles a
day.
Stable & Reliable - all facuets are manufacured under harsh moisture and
humidity testing.
Power Voltage: AC110 (60Hz) and Dc (4 x AA batteries)
Detection range: 12-18cm
Water pressure: 0.05 - 0.6 MPa
Water Temperature: 0 - 80°C
Tools you will need:
Phillips Screwdriver Pliers
Plumber’s putty Pipe tape
Adjustable Wrench

Product Diagram and Parts
Single inlet faucet
Hot & cold inlet faucet
Models:
Models:

Single inlet faucet
Models:
Product Diagram and Parts
1. Sensor faucet body
2. Braided hose
3. Self-tapping screw
4. Plastic sleeve
5. Rubber gasket
6. Stainless steel gasket
7. Nut
8. Control box
Battery installation
1. When the battery is out, the light sensor will flash in every 2 to 3 sec.
2. Replace the battery by taking off the cover and replace new battery.
*** Main control unit can be powered by AC or battery alone.

Single inlet control box
Clean filter :
Single inlet control box
1. Disconnect the power plug.
2. Turn off waterway.
3. Take out filter screen with
a plier.
4. Clean filter screen gently with
running water and replace the
screen. Connect the power.
Control Box
Power plugs
Terminal port
outlet in-flow
*** Hot/cold water mixing valve can be purchased.
hot
supply
cold
supply
BDM Variation
(Below Deck Mechnical)
Mixing Valve
Sensor control box
Sensor control box
*Hot & Cold hoses connect
directly to water supply.
Connection of Electric
Power plugs

Installation - Single inlet faucet
Single inlet faucet
1. Connect with water inlet hose.
2. Put the hoses into basin sink hole
3. Fix the sensor faucet body
with filler pieces and nut.
4. Hang the control box on the wall fixture
a. Drill two wall holes, and insert
the plastic expansion sleeve
and screws.

5. Connect faucet hose to outlet
part on control box. Connect
inlet port on control box to
pretempered water supply.
Connect faucet sensor power
cord to control box. Make sure
everything is secured then
connect control box power
cord to power outlet.
6. ***Optional: hot/cold water mixing valve can be purchased.
See control box figure (pg.4) .
Please test the water temperature before installation, hot water may
cause serious burn.

3. Fix the sensor faucet body
with filler pieces and nut.
4. Connect the hot and cold flexible
hoses to water supply valves.
4a. Connect electric wire A-B ; C-D
Hang the batteries box on the
fixed nut. Make sure everything is
secured then connect control box
power cord to power outlet.
Installation - Hot & Cold faucet
Hot & cold inlet faucet
Models:
1. Connect with water inlet hose.
2. Put the hoses into
basin sink hole.
5. Do not connect wires A-D directly.
1
4
5
4a

Sensor Adjustment & Troubleshooting
Sensor Adjustment
Troubleshooting
1. Turn off the water circuit and remove the faucet from the counter sink .
2. Use a clamp pliers to pick off the sponge which is at the back of the
sensor display.
3. Take the controller out, along the potentiometer and adjust lightly.
Turning clockwise will increase the inductive distance, turning
anti-clockwise will decrease the inductive distance.