Dyegoo GT06 User manual

GPS Vehicle tracker
(GPS+GSM+SMS/GPRS)
GT06 User Manual
(Version 3.2)
Thank you for purchasing the tracker. This manual shows how to operate the device
smoothly and correctly. Make sure to read this manual carefully before using this
product. Please note that specification and information are subject to changes without
prior notice in this manual. Any change will be integrated in the latest release. The
manufacturer assumes no responsibility for any errors or omissions in this document.

1. Summary
Working Based on existing GSM/GPRS network and GPS
satellites, this product can locate and monitor any remote targets by
SMS or internet.
Overview of the characteristics:
1.GSM 850/900/1800/1900MHZ.
2.GPS position.
3.Auto set APN.
4.200Mah Battery inside, Power-Cut alarm.
5.Motion detect, save GPRS flow and power.
6.GEO-fence alarm.
7.SOS Alarm.
8.Shock Alarm.
9.ACC Alarm.
10.Speed Alarm
11.Voice Surveillance.
12.Voltage DC 9-40V.
13.Enginee Cut off.
2．Accessories：

Power line:
Relay:
Microphone:
SOS line:
Manual

4. Wire defined
5.Device status indicators
5.1 Connect DC 9-40V power supply,push the switch(switch beside the sim
card holder), the red LED will light continuously.
5.2 The blue LED light continuously when searching the GPS signals. When
GPS position,the blue LED flashing.
5.3 The intermediate green LED (GSM signal state)
GSM signal is normal, green LED flashing. No GSM signal, the green
LED light continuously.
5.4 If work normal, after 5 minutes, all LED go off.
All LED will turn off after 5 minutes. When there is a new call, the LED will relight
andturnoff 5minutes.
6.Installation
6.1Prepareforinstallation
6.11 Product Check. Open the packing box and check the device’s model and accessories.
Ifthemodeliswrongor theaccessoriesnotcomplete, pleasecontactthedealer.

6.12 ChooseSIM card. Please insert aSIM card whichsupport GSM2G networktothe
device. Please take dealer’s advice as reference.
6.13 SIM card installation. Discharge the cover of the device and uncover the SIM card
holder.TheninserttheSIMcardandcoverSIM cardholder(asfollows).
6.14 Open thecover,Pushtheswitch.ThenPutbackthefrontcover.
6.15 Connect thedevicetothe9-40Vpower supply.
6.16 Installthedeviceinthehiddenplaceofthecar；
The SIM card must be with GPRS function and enough deposit. If your SIM card
needinputPIN whenpower on,pleasecancelit.
6.2 Installation
The GPS tracker must be installed under professional personnel.
Note：
1) Please install the device in the hidden place as followings：
2) Avoid being placed with signal radiators like reverse sensor ；
3) The device has GSM antenna and GPS antenna inside. Please ensure the

receiving side of the device is face up and without metal cover.
Note: The metal cover will lessen the receiving of GPS signals.
7. Device wiring requirements
7.1 The device power supply is DC 9-40V. The red line is positive pole while
the black line is negative pole.
7.2 The negative pole of power supply connects with ground or the metals.
Please do not connect with other ground lines.
7.3 When finishing the power supply wire connection, please make the plug of
power supply to the device.
8.The Device Working
8.1 Power on:Connecting to the power. Then the three LED indicators will light. The
device will upload the data to the online platform (the default interval of
uploading data is 15seconds). When thecar is in static statefor a long time, the
device willbe inenergysavingmodeanditwillbemoresmartandprecise.
8.2Power off：Pull offthepower plugthenpoweroffthedevice.
9.User Settings
9.1 SMS Commands instruction

1)Center Number
Text
command
Parameter
Sample
CENTER
Add
710#number#
711#number#
710#13500135000#
711#13800138000#
CENTER
Del
D01#
D02#
D01#
D02#
Command
Description
1)Center number can control the oil and power and
resume factory settings
2) Center number can receive the call and text of
vibration alarm and over speeding alarm.
3) SIM must display the income call number to control
oil and power.
4) Only 2 number can be center number.
5) Change center number must resend the command.
6)Add new center number by CETNER,A, and delete by
CENTER,D
Command
Feedback
Successful Setting：Add admin account 1 OK!
2) View Center Number

Text
command
Parameter
Sample
View
901#
901#
Command
Description
This directive is used to view Device Manager number.
Command
Feedback
Successful Setting：Admin1:
Admin2:
3)Authorized Number Set
Text
command
Parameter
Sample
Authorized
Add
101# number #
102# number #
103# number #
1：101#13800138000#
2：102#12345678912#
3：103#12345678912#
Authorized
Del
D11#
D12#
D13#
D11#
D12#
D13#
Command
Description
1) Authorization number for SMS control oil.
2) only three numbers to set the authorization number
3) change the authorization number needs to delete the
previous number

Command
Feedback
Successful Setting：Add Authorization account 1
OK!
4) View Authorized Number
Text
command
Parameter
Sample
View
authorized
C10#
C10#
Command
Description
This directive is used to view the equipment
authorization number
Command
Feedback
Successful Setting：
Authorization 1：
Authorization 2：
Authorization 3：
5)APN Setting
Text
command
Parameter
Sample
APN Setting
802#username#password#
1：802#intenet#123#123#
2: 802#internet#
Command
APN differs according to the local telecom operators.