Dyegoo GT06 User manual

GPS Vehicle tracker
(GPS+GSM+SMS/GPRS)
GT06 User Manual
(Version 3.2)
Thank you for purchasing the tracker. This manual shows how to operate the
device smoothly and correctly. Make sure to read this manual carefully before
using this product. Please note that specification and information are
subject to changes without prior notice in this manual. Any change will be
integrated in the latest release. The manufacturer assumes no responsibility
for any errors or omissions in this document.

1. Summary
Working Based on existing GSM/GPRS network and GPS satellites,
this product can locate and monitor any remote targets by SMS
or internet.
Overview of the characteristics:
1.GSM 850/900/1800/1900MHZ.
2.GPS position.
3.Auto set APN.
4.300Mah Battery inside, Power-Cut alarm.
5.Motion detect, save GPRS flow.
6.SOS Alarm.
7.Shock Alarm.
8.ACC Alarm.
9.Speed Alarm
10.Voice Surveillance.
11.Voltage DC 9-50V.
12.Enginee Cut off.
2．Accessories：

Power line:
Relay:
Microphone:
SOS line:
Manual

3. Specs
1）.GSM：850/900/1800/1900MHZ
2）.GPRS: Class12, TCP/IP
3）.Working Voltage：9-50V DC
4）.Working current：≈22mA (12VDC)
5）.Working current：≈12mA (24VDC)
6）.GPS locating time：Cold start≈38s（Open sky）
Warm start≈32s
Hot start≈2s（Open sky）
7）.GPS Precision：10m（2D RM）
8）.Working temperature：-20℃～+70℃
9）.Working humidity：20%～80%RH
10）.Measurement：98（L）×52（W）×16.5（H）mm

4. Wire defined
5.Device status indicators
5.1 Connect DC 9-50V power supply and the red LED will light continuously.
5.2 The blue LED light continuously when searching the GPS signals. When GPS
position,the blue LED flashing.
5.3 The intermediate green LED (GSM signal state)
GSM signal is normal, green LED flashing. No GSM signal, the blue LED
light continuously.
All LED will turn off after 5 minutes. When there is a new call, the LED will
relight and turn off 5 minutes later.
6.Installation

6.1 Prepare for installation
6.11 Product Check. Open the packing box and check the device‘s model and accessories.
If the model is wrong or the accessories not complete, please contact the
dealer.
6.12 Choose SIM card. Please insert a SIM card to the device. Please take dealer’s
advice as reference.
6.13 SIM card installation. Discharge the cover of the device and uncover the SIM
card holder. Then insert the SIM card and cover SIM card holder (as follows).
6.14 Open the cover, Push the switch to make the battery working. Then Put back the
front cover and screw it up.
6.15 Connect the device to the 9-50V power supply.
6.16 Install the device in the hidden place of the car；
The SIM card must be with GPRS function and enough deposit. If your SIM card
need input PIN when power on, please cancel it.
6.2 Installation
The GPS tracker must be installed under professional personnel.
Note：
1) Please install the device in the hidden place as followings：
Under Front windshield；
In the front instrument panel；
Under back windshield；
2) Avoid being placed with signal radiators like reverse sensor ；
3) The device has GSM antenna and GPS antenna inside. Please ensure the

receiving side of the device is face up and without metal cover.
Note: The metal cover will lessen the receiving of GPS signals.6. The
device connecting requirements.
7. Device wiring requirements
7.1 The device power supply is DC 9-50V. The red line is positive pole while
the black line is negative pole.
7.2 The negative pole of power supply connects with ground or the metals.
Please do not connect with other ground lines.
7.3 When finishing the power supply wire connection, please make the plug
of power supply to the device.
8.The Device Working
8.1 Power on: Connecting to the power. Then the three LED indicators will light. The

device will upload the data to the online platform (the default interval
of uploading data is 15seconds). When the car is in static state for a long
time, the device will be in energy saving mode and it will be more smart
and precise.
8.2 Power off：Pull off the power plug then power off the device.
9.User Settings
9.1 SMS Commands instruction
1)Center Number
Text command Parameter Sample
CENTER Add
710#number#
711#number#
710#13500135000#
711#13800138000#
CENTER Del
D01#
D02#
D01#
D02#
Command
Description
1)Center number can control the oil and power and resume
factory settings
2) Center number can receive the call and text of
vibration alarm and over speeding alarm.
3) SIM must display the income call number to control

oil and power.
4) Only 2 number can be center number.
5) Change center number must resend the command.
6)Add new center number by CETNER,A, and delete by
CENTER,D
Command
Feedback
Successful Setting：Add admin account 1 OK!
2) View Center Number
Text command Parameter Sample
View 901# 901#
Command
Description
This directive is used to view Device Manager number.
Command
Feedback
Successful Setting：Admin1:
Admin2:

3)Authorized Number Set
Text command Parameter Sample
Authorized
Add
101# number #
102# number #
103# number #
1：101#13800138000#
2：102#12345678912#
3：103#12345678912#
Authorized
Del
D11#
D12#
D13#
D11#
D12#
D13#
Command
Description
1) Authorization number for SMS control oil.
2) only three numbers to set the authorization number
3) change the authorization number needs to delete the
previous number
Command
Feedback
Successful Setting：Add Authorization account 1
OK!