Dynatron D4800 User manual

S i m p l y t h e b e s t I n C a r S e c u r i t y
FREEPHONE 0800 508 904
MODEL D4800 “Upgrade” User Manual
14/07/2008
The DYNATRON D4800 has been tested to and meets AS/NZS 3749:2003 Part A provided that the vehicle is equipped with an
automatic immobiliser of manufactures origin and that the vehicles remote has "rolling code".
ARMING AND DISARMIN G
To arm the D4800, press the lock button on the remote control supplied by the vehicle manufacturer. Arming the system is
accompanied by flashes from the indicators (the number is dependant upon each manufacturer) and optionally two "chirps" from
the Dynatron Battery Backup siren. To disarm, press the unlock button on the factory remote control which is accompanied by a
single "chirp" (also optional). Both the indicator and siren confirmation from the D4800 can be deleted where the factory system
provides its own.
AUTO RE-ARMIN G
The D4800 will auto re -arm only in vehicles with an auto re -lock feature. Some vehicles will re -lock doors if the vehicle is not
entered for a given amount of time.
INTRUSION DETECTION
The D4800 is equipped with four zones of protection, doors, boot, bonnet, glass breakage & ignition. Each zone can be triggered a
maximum of three times after arming. When a zone is triggered, the siren and indicators will sound and flash for 30 seconds. Both
indicators and siren will reset for five seconds after each 30 -second trigger period before sounding due to subsequent triggers.
ENGINE IMMOBILISATION
The vehicle's manufacturer usually provides engine immobilization. The D4800 does provide another two independent circuits of
immobilization, however they are only connected at special request.
GLASS BREAKAGE PROTECTION
The 4600 is equipped with a sophisticated glass breakage detection unit. The system will only respond to the breaking of any glass
in the vehicle. To test the unit simply wind up all the windows and arm the D4800. Wait 30 seconds before rapping the driver's
side window with a metal object such as a coin. The siren and indicators will sound and flash. There should be no trigger, if you hit
the window or body of the vehicle with your hand. This eliminates all false alarms.
IMPORTANT NOTICE ABOUT GLASSBREAK SENSORS
The Security of your car is important to us. With the wider use of aftermarket film window tints now being applied the efficiency of
your AS/NZS tested and approved Glassbreak Detector may be compromised. If you have or intend to have aftermarket film tints
applied please be aware that this may compromise the tuned frequency response of your detector. This is especially true of
station wagon and larger people mover vehicles and where side windows are rubber mounted or pillar less. As the owner of the
vehicle it is important that you discuss any film tinting with Dynatron or your Dynatron installer. The detector can often be recalibrated
to compensate for a film tint, but you may be advised to pay for and fit an additional interior or movement sensor.
BATTERY BACKED-UP SIREN
The D4800 is provided with a siren that has it’s own power supply in the form of rechargeable batteries. These batteries are permanently
located inside the siren and are trickle charged from the cars charging system. If the wires are cut to the siren or if the battery
terminals are removed from the cars battery the battery backed up siren will sound until the batteries in the siren are exhausted.
The D4800 is provided with two small chrome and black keys that enable the user to turn the siren off at the siren proper. This
feature is often used by mechanics so it is a good idea to leave one siren key on your vehicle key set. Note that turning the siren off
will not turn the alarm/immobilizer off.
DIAGNOSTICS
Whenever the alarm system is triggered, the memory of t he module will be automatically updated with the number of the zone
responsible. The report will be displayed upon the next disarm command. Both the indicators and status LED will flash a number of
times. The table below describes the number for each zone.
ZONE NUMBER ZONE NAME
1 Bonnet
2 Millivolt sensing
3 Doors & boot switches
Each zone will trigger a maximum of three times per arm cycle. Once a zone has sounded the siren three times it is ignored until the
next time the system is armed. At no time does the immobiliser disarm.

PROBLEM SOLVING
System won't arm/disarm
- Ensure all vehicle doors are closed and ignition switch is off.
- Check whether vehicle's central locking responds to remote control.
- Ensure siren is switched on
- Ensure vehicle does not have a flat battery.
System won't trigger
- Ensure that you have allowed at least 40 seconds after setting the system, before testing.
- If testing boot, ensure boot light comes on only when boot switch is operated; it must not remain on constantly.
The remote fails to operate
- Try your spare remote transmitter.
- Contact the dealer the vehicle was purchased from or vehicle manufacturer.
OVERRIDE
The system can be overridden by means of a Personal Identification Number (PIN). Every unit has its own PIN. This PIN
is issued with every system by means of a credit card sized PIN card. Do not lose this card. Do not leave it in your vehicle.
Do not tell anyone your PIN number. Do store the PIN ca rd in a safe and confidential place. Storing the PIN number in a
secure place in your cell phone is an ideal way to store the number.
OVERRIDE PROCEDURE
1. Insert the ignition key into the ignition switch and turn to the ON position. The blue or re d status LED mounted on the dash
will glow constantly.
2. Turn the ignition key back to the ACC position, the status LED will begin to flash slowly. Count the number of flashes for the first
digit in the PIN of the alarm/immobiliser. Return the key to the ON position when the correct number is counted.
3. Repeat step 2 for the remaining digits in the PIN. When all four digits are entered, the indicators will flash once the system will
then disarm Please Note “Any digit marked '0', indicates 10 flashes .
NB> If the engine is not started within 40 seconds of over -riding, the alarm/immobiliser will immobilize the engine It is necessary to
enter the PIN each time the engine is turned off and the system has auto immobilized.
WARRANTY
This product is warranted by DYNATRON (NZ) Ltd, P.O Box. 302-384, North Harbour, Auckland. New Zealand. Subject to the
conditions stated below, to be free from manufacturing defects and faulty material within the warranty period stated below.
CONDITIONS
 That the warranty registration has been completed in full at the time of purchase and / or installation and is produced when
warranty service is sought.
 The warranty does not cover general maintenance such as cleaning of bonnet switches, door switches, light switches etc, nor
replacement of consumable items such as pilot lamps or transmitter batteries.
 Should a product defect become apparent within the warranty period DYNATRON (NZ) LTD will repair the product free of charge
for parts only. Labour to remove and install the serviced product will be the responsibility of the original installer and their
prescribed labour
 Warranty terms and conditions. This is a return to base warranty and should a mobile service be required, a call charge may
apply.
This warranty shall be null and void if
1. The product has been repaired by any other person other than by an authorized DYNATRON service centre
2. The product has been altered or tampered with in any way or the serial number altered, defaced or removed
3. The defect has been caused by negligence by the owner or their agent.
4. The product has not been operated correctly, installed by an authorized DYNATRON installer or has been subjected to misuse
or undue wear and tear.
5. The control module is damaged by water.
THE WARRAN TY DOES NOT COVER T HE FOLLOWING COSTS.
Transport of the product to and from DYNATRON service centres. Insurance of the product in transit to or from the DYNATRON
service centres. Cost of any service call where the product is found by DYNATRON to be in good working order. Cost of any
unauthorized towage of the vehicle will not be met by DYNATRON NZ LTD.
DISCLAIMER
Dynatron systems have all been tested and approved to Australian and New Zealand Standards and only Dynatron Authorised
Installers have been given the information to install your system correctly to those same standards. Dynatron (NZ) Limited will
accept no liability for any independent in stallation of this product, its performance or operation. We believe that the responsibility
for a system performing according to published and verifiable standards rests primarily with you as the owner and end user.
But, should you have any concerns about your Dynatron system then please call us at Dynatron direct during working
hour’s toll free on 0800508904 and speak to Customer Services or one of our Technical team– We are here to help and we will
see that you get “Simply the Best InCar Security” for your car.

PLEASE COMPLETE DETAILS BELOW AND REGISTER YOUR DYNATRON:
It is very important that you’re DYNATRON Security System details are recorded below. The units Serial Number is
recorded in our secure database which is directly associated with the Emergency Override PIN and it is this PIN Number
that will enable your security system to b e overridden. REMEMBER, A THREE YEAR WARRANTY ON THE MODULE
ONLY IF THE INSTALLATION IS PERFORMED BY AN AUTHORIZED DYNATRON INSTALLER 12 MONTHS ON
REMOTES SENSORS AND ACCESSORIES.
OWNERS DETAILS:
OWNER NAME
DYNATRON MODEL
MODULE SERIAL NUMBER
VEHICLE REGISTRATION NUMBER
VEHICLE MAKE VEHICLE MODEL YEAR
INSTALLER DETAILS:
INSTALLER COMPANY NAME
INSTALLER NAME
DATE INSTALLED
LABOUR WARRANTY PERIOD
***PHONE US ON 0800 508 904 TO REGISTER YOUR DYNATRON***

DYNATRON ACCESSORIES
Dynatron offers a full range of sensors, each one designed for a specific application.
Microwave Sensor Glassbreak Sensor Tilt Sensor
Shock Sensors Ultrasonic Sensor Battery backed up Siren
Dynapage Cellular pager Dynatrace GPS Tracking Systems
Door
Motors