Dynaudio Focus 60 XD User manual

Owner’s
manual
Focus XD

Owner’s Manual Focus XD
32
dynaudio.com/focusxd
We thank you / Table of contents
Thank you for choosing Dynaudio Focus XD loudspeakers.
Every Focus XD model features advanced Dynaudio
loudspeaker technology that turns listening to music into an
impressive experience. This technology results from many
years of intense research and development, the highest
quality standards in production, and Dynaudio’s enduring
passion for musical truth.
Each Focus XD loudspeaker is constructed by Dynaudio’s master craftsmen in Denmark
to these high standards of quality. To realize the highest sound quality from the Focus XD
models, some areas should be addressed, as will be explored on the following pages.
By considering the tips and suggestions, you will achieve the maximum performance and
enjoyment of the Focus XD and its advanced musical capabilities for a long time to come.
We hope you have a great time listening to your favourite music.
Dynaudio
Thank you
4 Safety information
5 About this guide
5 Expressions and symbols used
6 Scope of delivery
6 Unpacking
6 Packaging material
6 Disposal
7 Setting up
8 Floor-standing loudspeaker setup
8 Compact loudspeaker setup
9 Selecting the installation location
9 Right and left loudspeaker
10 Distance to walls
10 Distance to the listening position
11 Loudspeaker toe-in
11 Grille
12 Connection and operation
13 Connections and control elements
14 Remote control
14 Control elements
15 Connecting the loudspeakers
15 Connecting the digital signal source
16 Connecting the analog signal source
17 Operating the loudspeakers
without controlling the volume
18 Adjusting the loudspeakers’ sound
18 Adjusting the low-frequency range
18 Adjusting the treble
19 Connecting the voltage supply
19 Switching on/standby mode
20 Selecting inputs on the loudspeakers
20 Selecting the hub inputs
20 Selecting a hub (HUB)
20 Selecting an input on the hub (INPUT)
20 Adjusting the volume
20 Muting the loudspeakers
21 Display
21 Malfunctions
24 Firmware update
25 Technical data
26 Care & maintenance
27 Warranty
Table of contents

Owner’s Manual Focus XD
54
dynaudio.com/focusxd
Safety instructions / About this guide
Safety
instructions
About this
guide
High sound pressure levels
Listening to high sound pressure levels over a longer period
of time may harm your hearing.
Dangerous electrical voltage
If the loudspeakers are connected to the mains voltage, a
dangerous electrical voltage is present inside the speakers.
To avoid auditory effect, do not listen to high sound levels over a longer period of time.
Never open the loudspeaker housing.
Do not operate defective loudspeakers and disconnect defective loudspeakers from
the mains voltage. Please contact your Dynaudio distributor if you have any problems.
Distributor addresses can be found in the Internet at www.dynaudio.com.
Use the supplied power cable to connect the loudspeakers to the mains voltage. Make
sure that the power supply cable is not damaged; exchange it for a new one if it has
been damaged.
Used expressions and symbols
In this operating manual following signs and symbols are used:
ATTENTION: Indicates a hazard that could result in damage or destruction of the product.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature
accompanying the product.
Indicates (in combination with a safety sign) a potentially hazardous situation which, if not
avoided, could result in minor or moderate injury or damage to equipment.
Indicates a hazard that could result in death or severe injury.
The arrow will identify steps to be performed. Please follow the instructions carefully.
Always make sure to follow the instructions given in these passages.
Multiple steps that should be performed consecutively are numbered.
Please follow these instructions carefully.
1.
2.
Note
Additional information is provided, which is important to fully understand the
loudspeaker and how to operate it.

Owner’s Manual Focus XD
76
dynaudio.com/focusxd
Unpacking / Setting up
1. 2 Focus XD loudspeakers (60 XD, 30 XD, or 20 XD)
2 Focus XD loudspeaker cloth covers (not shown)
2. 1 remote control
3. 2 power cables (country-specic version)
1 rst time setup manual (quick guide for installation, not shown).
Unpacking
Scope of
delivery
Disposal
After unpacking, make sure the system is complete and check the device and all
accessories for transport damage. Transport damage may be expected if the packaging is
already severely harmed. Do not attempt to commission a damaged device. If the contents
are incomplete or damaged, please contact your Dynaudio distributor.
Distributor addresses can be found in the Internet at www.dynaudio.com.
Packaging material
The packaging has been designed so that it may be reused if it was not damaged during
transport. Keep the packaging and use the original packaging for all further transport.
Disposal of used electrical and electronic equipment (applicable in European countries with
separate collection systems for this equipment).
This symbol on the product or its packaging indicates that the product may not be treated
as household waste. Instead it must be handed over to the applicable collection point for
the recycling of electrical and electronic equipment. By ensuring this product is disposed
of correctly, you will help prevent potential negative consequences for the environment and
human health. The recycling of materials helps to conserve natural resources.
For more detailed information on recycling this product, please contact your local authority,
community waste disposal ofce, or the shop where you purchased the product.
321
Spikes with sharp peaks
The oor-standing Focus XD loudspeakers allow for setup with spikes. The sharp peaks of
the spikes may cause injuries and damage sensitive surfaces like hardwood ooring or tile.
►Be careful when handling the loudspeakers.
►Place plates between the spikes and the surface to protect the underlying surface.
ATTENTION
Light, heat, electromagnetic radiation
Direct sunlight or excessive brightness can affect the colour of your loudspeakers’ natural
wood veneer. Built-up heat can lead to overheating. Electromagnetic radiation of different
devices can lead to mutual impairment to functions.
►Avoid placing the device in very warm, cold, or humid environments.
►To maintain the aesthetic quality of your loudspeakers for the long term, placement in
light-intensive, sunny environments should be avoided.
►Please ensure sufcient ventilation and observe the required distances around the
loudspeakers.
►Do not place the loudspeakers near devices with strong electromagnetic radiation or
devices that could be destroyed or damaged by magnetic elds.

Owner’s Manual Focus XD
98
dynaudio.com/focusxd
Setup / Location
The oor-standing Focus XD loudspeaker features a special base construction, which offers
both an ideal performance and mechanical basis. The spikes screwed into the end of the
feet on the base can be unscrewed and their height adjusted, to adapt to uneven oors.
When the spikes are retracted, the loudspeakers stand on rubber feet. These stabilize
the cabinet on an extremely small contact area, and therefore prevent any wobbling while
offering optimal resonance control.
The best setup variant depends on the nature of the room and the oor in particular.
Your Dynaudio distributor would be happy to assist you during setup.
The compact Focus models are designed to offer exceptional performance while taking up
minimal space. Due to adverse effects to the sound quality, compact loudspeakers should
not be placed on the oor. The mini-monitors will realize their optimum performance when
used in conjunction with a stand to position them at the proper height while absorbing any
resonance. Please contact your Dynaudio distributor for more details.
Due to its dimensions, you can also place the loudspeaker on a ledge or shelf or on top of
furniture. To avoid the possibility of any negative inuence on sound quality, make sure to
utilize a stable surface offering a wide enough space in front of the loudspeakers as to not
limit the sound quality and performance.
The Focus XD loudspeakers do not require special positioning, though the quality of the
individual loudspeakers’ sound is affected by the acoustic properties of the room. Since
rooms are shaped uniquely, the positioning of the loudspeakers results in totally different
behaviour. For example, large rooms without much furniture and many clean, hard wall
surfaces can give a bright and diffuse sound with diverse echoing frequencies. A room with
thick carpet, curtains and soft furniture surfaces will give a slightly warmer, darker and less
lively sound.
The following information steps are therefore general directions that will make correct
positioning easier to achieve. Furthermore, we recommend taking advantage of the
services provided by your Dynaudio distributor to fully exploit the sound potential of your
loudspeakers in your own listening room.
The outside of the left and right loudspeakers is different, with a different arrangement of the
display (see gure above) and labelling on the rear side.
►Position the loudspeakers in the desired location.
Floor-standing loudspeaker
setup
Selecting the installation
location
Compact loudspeaker setup
Right and left loudspeaker
Left Right
Display
Spike on oor-standing Focus XD.

Owner’s Manual Focus XD
1110
dynaudio.com/focusxd
Setup / Location
Every loudspeaker not only disperses sound energy directly into the room, but also to
the side and even backwards. As a result, time-delayed reections occur and add to the
original music signal. Thus, when loudspeakers are positioned too close to walls, the sound
quality can be restricted. Focus XD loudspeakers were developed to be placed free-
standing, and therefore they reach their optimum performance when positioned as clear of
any walls as possible.
►To reduce possible inuences from the back and sidewalls, the distance to these
boundaries should ideally not be less than 0.5 meter.
►Adjust the sound of your loudspeakers (see page 18).
• The distance between each loudspeaker and your listening position should be the same
(B). Try to achieve an isosceles triangle.
• The distance between the loudspeakers should be the same or, preferably, slightly less
than the distance between each loudspeaker and your listening position (A, B).
• The closer the listening position is in relation to the loudspeakers, the closer the
speakers can be positioned to each other.
• As a starting point, it is recommended that the speakers be about 2 meters apart from
each other for the best results (A).
• If the speakers are positioned too close to each other, the stereo image will not seem
realistic; if that distance is too wide, the image may leave an acoustic hole in the middle.
• Paying attention to the image during listening tests will help dictate optimum placement
during experimentation and setup.
Distance to walls
Distance to the listening
position
Depending on your personal listening environment and room dimensions, the loudspeakers
may be angled in towards the listening area to focus the sound radiation. This positioning
will typically improve imaging and is especially recommended by Dynaudio. However, you
are free to select the precise position based on your personal listening habits.
A cloth grille is included and can be afxed to the cabinet to help protect the drivers from
dust and any other inuences. The grille is acoustically optimized, but the highest sound
quality levels will be attained without any grille covers in place during listening.
If a front grille is used, it is held on the front of the housing by means of magnets.
Removing and attaching the front grille:
►To remove the grille, gently pull the grille at all corners straight away from the front.
►To t the grille, line it up exactly in front of the housing with the logo facing upwards and
carefully push the cover onto the loudspeaker.
Loudspeaker toe-in
Grille
A≤B
BB
A
A
D ≥ 0.5 m
B

Owner’s Manual Focus XD
1312
dynaudio.com/focusxd
Connection and control elements
Connections
and control
elements
This section describes the connections and control elements
for the components. Please contact your Dynaudio distributor
if you have any problems with connection and start-up.
Distributor addresses can be found on the Internet at
dynaudio.com. The active loudspeakers have an integrated
amplier and can be controlled with the remote control.
CONNECTIONS AND CONTROL ELEMENTS
Digital Audio Digital connection. IN = input, OUT = output
Analog Audio
Analog connection. IN = input, Input sensitivity = manual correction of the input sensitivity (+6/ 0 / -6 dB)
Service
USB port for rmware update
Speaker Position
Sound adjustment (depending on the position of the loudspeakers). Sound adjustment is performed with a
rotary knob with 7 positions. With the 3 main positions, the rotary knob clicks into place:
Neutral = with free-standing placement. Wall = if placed near a wall. Corner = if placed in a corner
Treble
Treble adjustment (+1 / 0 / -1 dB)
Zone
Selecting the audio zone (Xeo hub operation)
Loudspeakers assigned to different zones can be controlled separately via the remote control.
The zones are identied as Red, Green, and Blue.
Channel Mode
Master = loudspeaker operated as master. Slave = loudspeaker operated as slave.
External = loudspeaker congured as active loudspeaker (at full performance)
Power
Power switch. I = The loudspeaker is on. The loudspeaker can be activated and deactivated via the remote
control. If the loudspeaker is activated and there is no signal, it will switch to standby mode.
O= The loudspeaker is completely off.
Mains socket. To connect the loudspeaker to the mains voltage.

15
dynaudio.com/focusxd
14
Remote control / Connecting the loudspeakersOwner’s Manual Focus XD
Remote control
The remote control can be used to turn the loudspeakers on and off, change the volume,
switch between digital and analog input, switch the display on or off, and select a hub and
its connected signal sources.
►To connect the loudspeakers, switch all components off.
Connecting the digital signal source
You can connect your loudspeakers as follows:
• Both loudspeakers are connected using cables. This requires two digital cables but the
systems benets from signal processing of 24 bits/192 kHz.
• You only connect one loudspeaker using a cable; the connection between the
loudspeakers is wireless. This requires one digital cable and provides signal processing
capabilities of 24 bits/96 kHz.
• Both loudspeakers are operated wirelessly via a Dynaudio Hub or Connect box with
signal processing of 24 bits/96kHz.
Connecting both loudspeakers with cables
1. Connect the digital output for the signal source to the digital input (Digital Audio IN) on
one loudspeaker. You can choose whether to use the right or left loudspeaker.
2. Operate the connected loudspeaker as master by setting the Channel Mode switch on
the rear side of the housing to Master.
3. Connect the digital output on the master loudspeaker to the digital input (Digital Audio
IN) on the other loudspeaker.
4. Operate the loudspeaker connected in this step as slave by setting the Channel Mode
switch on the rear side of the housing to Slave.
CONTROL ELEMENTS
MUTE Muting the loudspeakers
Briey pressing this button will mute or unmute the selected
loudspeaker.
ON/OFF
Loudspeaker on/off
= on. = switch to standby
VOLUME
Changing the volume
= louder. = quieter
DIRECT
Direct selection
= toggle between digital and analog input
= switch the display on/off
INPUT
1/2/3/4
Selecting the signal source
Selects one of the signal sources Line In, Optical In, Coax In
or USB In from the active hub.
HUB
A/B/C
Selecting the Hub or Connect
Selects one of three possible Hubs or Connects A, B, or C.
Connecting the digital signal source.
Connecting
the
loudspeakers

Owner’s Manual Focus XD
1716
dynaudio.com/focusxd
Connecting the analog signal source / Operating the loudspeaker without controlling the volume
Connecting the analog signal
source
The loudspeakers can also output signals
from an analog signal source. The signal
source is connected to the analog inputs.
1. Connect the left analog output from
the signal source to the analog
input (Analog Audio IN) on the left
loudspeaker.
2. Connect the right analog output
from the signal source to the analog
input (Analog Audio IN) on the right
loudspeaker.
3. Operate one loudspeaker as master
and the other as slave by setting the
respective switch (Channel Mode)
correspondingly on the rear side of the
housing. The assignment of master and
slave is irrelevant.
Operating the loudspeakers
without controlling the volume
You can also operate the loudspeakers
without controlling the volume yourself.
The ampliers integrated into the
loudspeakers function as a power
amplier; volume is controlled via the
source signal (e.g. pre-amplier).
1. Connect the left analog output from
the signal source to the analog
input (Analog Audio IN) on the left
loudspeaker.
2. Connect the right analog output
from the signal source to the analog
input (Analog Audio IN) on the right
loudspeaker.
3. Set the Channel Mode switch on the
back side of the housing to External.
Connecting only one
loudspeaker with a cable
1. Connect the digital output for the signal
source to the digital input (Digital
Audio IN) on one loudspeaker. You can
choose whether to use the right or left
loudspeaker.
2. Operate the connected loudspeaker as
master by setting the Channel Mode
switch on the rear side of the housing
to Master.
3. Operate the other loudspeaker as slave
by setting the Channel Mode switch
on the rear side of the housing to
Slave.
Operating the loudspeakers
via a Hub or Connect
Dynaudio’s innovative Connect system
offers the option to operate the loud-
speakers completely wirelessly. The
connection to the loudspeakers is
established by either a Dynaudio Hub or
Connect box to which the analog and/
or digital sources can be connected. For
more details, please refer to the Connect
Owner’s Manual or learn more at http://
www.dynaudio.com/home-audio/connect/
1. Install and congure the Connect
system according to the Connect
owner’s manual.
2. On the rear side of the housing,
select the red, green, or blue
zone. Loudspeakers that belong to
a common zone can be operated
together using the remote control.
3. Operate one loudspeaker as master
and the other as slave by setting the
respective switch (Channel Mode)
correspondingly on the rear side of the
housing. The assignment of master and
slave is irrelevant.
Operating via Hub or Connect.Operating with a cable. Connecting the analog signal source.
High sound pressure levels
In the External operating mode, signals
are amplied at the maximum. Connecting
a signal source with an uncontrolled or
maximum level can harm your hearing and
cause damage to the components.
►Only connect controllable signal
sources.
►Before switching on the loudspeakers,
turn down the volume for the signal
source using its volume control.
Connecting the digital signal source

19
dynaudio.com/focusxd
18
Owner's Manual Focus XD Adjusting the loudspeaker’s sound / Connecting the voltage supply
The sound of Focus XD loudspeakers can
be adjusted by increasing or lowering high
and low frequencies. Each loudspeaker
can be set separately and individually
based on the room conditions and
personal listening preferences.
Adjusting the low-frequency range
The Speaker Position rotary knob allows
you to lower low frequencies. This allows
you to balance out elevated or cancelled-
out low-frequency signal portions, as they
often occur in living spaces.
►Set the Speaker Position rotary knob
to the desired position on the back side
of the housing for each loudspeaker.
There are 2 additional intermediate
stages between each of the main
positions that click into place (Neutral,
Wall, and Corner).
–– Neutral: free-standing loudspeaker (no
change to sound).
–– Wall: if placed near a wall.
–– Corner: if placed in a corner.
Adjusting the treble
Using the Treble switch on the rear side
of the housing allows you to adjust the
character of the sound to your listening
preferences.
►Set the Treble switch on the rear side
of the housing to one of three settings:
• +1 dB: Increase, creates a somewhat
brighter sound.
• 0 dB: Neutral position, no change.
• –1 dB: Lowering, creates a somewhat
warmer sound.
►Use the supplied power cable to
connect the loudspeakers to the mains
voltage and switch it on using the
power switch (POWER) on the rear
(position: I).
Switching on/standby mode
To switch the loudspeaker on from
standby mode:
►Point the remote control at the
loudspeaker and press the ON button.
The loudspeaker will automatically
search for an audio signal or an
active hub. If found, the signal will be
output. If there is no input signal, the
loudspeaker will go into standby mode
after a certain period.
►To switch it back on, press ON or start
music playback.
To switch a loudspeaker out of
operation to standby mode:
►Point the remote control at the
loudspeaker and press the OFF
button. The loudspeaker will go into
standby mode. To completely switch
off the loudspeaker, turn the POWER
switch on the rear to O. However, the
loudspeaker can then no longer be
switched on via the remote control.
Adjusting the
loudspeakers’
sound
Connecting the
voltage supply
Note
Before connecting the device,
check whether the mains voltage
listed on the rear side of the
speakers matches that present at
the installation site.

Owner’s Manual Focus XD
2120
dynaudio.com/focusxd
Display / Display meaningsSelecting inputs on the loudspeakers / Adjusting the volume
►Press the DIRECT button on the
remote control. The loudspeakers
toggle between the analog and digital
input if the corresponding signal
sources are connected.
Selecting the Hub or Connect inputs
Optionally, the loudspeakers can also be
operated with a Dynaudio Hub or Connect
box. For details on operation via Hub or
Connect, please refer to the Connect
Owner’s Manual.
Selecting a Hub or Connect (HUB)
►Press HUB A, B, or Con the remote
control. The chosen Hub or Connect is
selected as the signal source.
Selecting an input on the Hub or
Connect (INPUT)
►Press INPUT 1, 2, 3, or 4on the
remote control. The selected signal
source will be played back.
Night Mode
►Briey pressing the MOON button
on the remote control will activate
Night Mode. When in Night Mode, the
status LEDs will only be lit up when
the speaker is receiving commands
from the remote control. After a few
seconds, the LEDs will turn off. Press
the MOON button again to disengage
Night Mode.
Fixed Volume
►Press and hold the MUTE button to
set the volume to a xed, high level.
To disengage the Fixed Volume mode,
simply change the volume level using
the Volume +/- buttons on the remote.
Disabling/Enabling Autosense
►In normal operation, the Focus XD will
go to stand-by if it does not sense an
incoming signal. Hold the ”Direct In”
button on the remote for 5 seconds,
to disable or enable Autosense. The
status LED will blink once for enabling,
and twice for disabling Autosense.
Note that when Autosense is off, the
speaker will remain On, until the user
actively sets the speaker in Stand-By
using the Off button.
The display on the top edge of the housing
indicates the operational state of the
loudspeakers and system using LEDs with
various colours and ash functions.
The display can be switched on or off with
the button on the remote control.
Change the volume by pressing the
VOLUME button on the remote control.
►Press to turn the volume up.
►Press to turn the volume down.
Muting the loudspeakers
►Briey pressing the MUTE button on
the remote control will mute or unmute
the selected loudspeaker.
Selecting inputs on the
loudspeakers
Display
Adjusting the volume
Note
If loudspeakers are operated in hub
mode in different zones, the volume
is controlled separately. For details
on operation via the Xeo hub,
please see the Xeo owner’s manual.
LED DISPLAY MEANINGS
On-state
The bottom LED is illuminated in blue.
The bottom LED is ashing in blue.
The bottom LED is illuminated in violet.
The loudspeaker is switched on and an audio signal
connected to a Hub or Connect is played back.
The loudspeaker is switched on, but an audio signal
cannot be found on the selected input.
The loudspeaker is switched on and an audio signal
connected to a local input is played back.
Off-state
The bottom LED is illuminated dimly in red. The loudspeaker is in standby mode.

Owner’s Manual Focus XD
2322
dynaudio.com/focusxd
Display meanings
LED DISPLAY MEANINGS
Hub or Connect connection
The bottom LED is ashing red. There is no active Hub or Connect, or no
connection to a Hub or Connect possible
Switch-on process
LEDs are illuminated one by one. The loudspeaker is being switched on.
Switch-off process
The LEDs go out one by one.
In the nal state, only one LED is
illuminated dimly in red.
The loudspeaker is being switched off.
Displaying the direct input
One of the two LEDs ashes. LED 1 = digital INPUT
LED 2 = analog INPUT
LED DISPLAY MEANINGS
Displaying the selected Hub or Connect
One of the three LEDs ashes. LED 1 = HUB A
LED 2 = HUB B
LED 3 = HUB C
Displaying the input source
One of the four LEDs ashes. LED 1 = INPUT 1
2nd LED = INPUT 2
3rd LED = INPUT 3
4th LED = INPUT 4
Searching for an input
The blue LED ashes; the lights in the
white LEDs move back and forth.
Searching for an active input
Searching for an active input on the hub
The blue LED ashes, the white LEDs
briey light in order. A hub input has been selected and the hub is
searching for an active input.

Owner’s Manual Focus XD
2524
dynaudio.com/focusxd
Display meanings Technical data
1. Copy the rmware le onto an empty
USB stick.
2. Switch the loudspeaker off using the
power switch on the rear of the device.
3. Insert the USB stick in the USB port on
the rear side of the housing.
4. Switch the loudspeaker on (power
switch on the rear of the device).
The rmware update is performed
automatically.
The while LEDs will light in
ascending order (see above).
The procedure is completed in just
a few seconds. The loudspeaker
enters standby mode automatically.
5. Switch the loudspeaker back off and
remove the USB stick.
6. Repeat steps 2–5 with the second
loudspeaker.
Firmware update
Note
The rmware update must be
performed separately for each
loudspeaker.
LED DISPLAY MEANINGS
Volume, mute
A number of white LEDs are illuminated.
The rst LED ashes.
The number of LEDs indicates the selected volume.
The loudspeaker is muted.
Firmware update
The white LEDs light in order. A rmware update is being performed.
LOUDSPEAKERS FOCUS 20 XD FOCUS 30 XD FOCUS 60 XD
Frequency range (± 3 dB) 39 Hz – 24 kHz 29 Hz – 24 kHz 18 Hz – 24 kHz
Power consumption during operation 18 – 200 W 18 – 200 W 18 – 200 W
Power consumption in standby < 1 W (with active network) < 1 W (with active network) < 1 W (with active network)
Amplier performance Subwoofer: 150 W
Tweeter: 150 W
Subwoofer: 150 W
Midrange: 150 W
Tweeter: 150 W
Subwoofer 1: 150 W
Subwoofer 2: 150 W
Midrange: 150 W
Tweeter: 150 W
Dimensions (H x W x D) 360 x 198 x 307 mm 980 x 198 x 307 mm 1095 x 213 x 337 mm
Weight 8.65 kg 18.5 kg 27 kg
Voltage supply 100 – 120 V/220 – 240 V,
50/60 Hz
100 – 120 V/220 – 240 V,
50/60 Hz
100 – 120 V/220 – 240 V,
50/60 Hz
Inputs Digital audio IN (16/24 bit: 44.1/48/88.2/96/176.4/192 kHz), cinch, SPDIF (75 ohm coax)
Digital audio OUT (16/24 bit: 44.1/48/88.2/96/176.4/192 kHz), cinch, SPDIF (75 ohm coax)
Analog audio IN (input sensitivity: +6 dB/0 dB/–6 dB), cinch, 1/2/4 Vrms
Service, USB, rmware upload
Wireless (bit/kHz: 16/48 and 24/96), 2.4/5.2/5.8 GHz

Owner’s Manual Focus XD
26
dynaudio.com/focusxd
27
dynaudio.com/focusxd Care & maintenance / warranty
Warranty The warranty is based on the statutory regulations of
the respective country. Furthermore, Dynaudio offers an
extended warranty after registration online at http://www.
dynaudio.com/register. Please refer to the information
during registration for warranty periods.
This warranty only covers faults or defects in material and production. Damage caused as a
result of abuse, misuse or defective electronics is not covered by the warranty. All warranty
claims must be accompanied by a copy of the original purchase invoice and warranties are
only valid in the country or market of original origin or distribution. Should warranty service
be required, it must be arranged for in the country of purchase by an authorized Dynaudio
dealer.
Malfunctions
You can ask your Dynaudio distributor for assistance at any time or contact the Dynaudio
helpline at [email protected].
Further information can also be found on the Focus XD website at focusxd.dynaudio.com.
Dynaudio loudspeakers require no special
treatment apart from the kind of careful
handling you would normally apply to any
high-tech product in your home.
Cleaning the loudspeakers
►Switch off all components of your
system when cleaning any of these
components or in case of extended
absences.
►Avoid touching the tweeter domes as
any change of their shape may have an
impact on sound quality.
►Clean the cabinet and other plain parts
with a soft dry or slightly damp cloth
only.
►Remove dust on the woofer
diaphragms with a ne furniture brush.
All materials used by Dynaudio are
integrated with exceptional care. By
taking care of your loudspeakers, you will
preserve the nish and build quality for a
very long time.
Aggressive cleaning uids
All-in-one cleaning agents, aggressive
cleaning uids or special furniture polishes
may damage the cabinet surface or other
speaker parts.
►Use a soft dry or slightly damp cloth
when cleaning the cabinet and other
plain parts.
Care &
maintenance

Dynaudio A/S
8660 Skanderborg
Denmark
www.dynaudio.com
Focus XD - Owner’s manual,
version 10/17.
All text and image copyrights reserved.
Subject to change without notice.
Focus XD
Designed and engineered
by Dynaudio Labs
in Denmark