6Installation instructionsDX-TVM112
STEP 2 - Option 2: Installing on a solid concrete or concrete block wall*
CAUTION: To prevent property damage or personal injury, never drill into mortar between blocks. Mount wall plate
directly onto the concrete surface.
1Align the wall plate template (P) at the height you determined in the previous step, make sure that it is level,
then tape it to the wall. Use a pencil to mark the lag bolt hole locations (3). Remove the template.
2Drill pilot holes to a depth of 2 1/2 in. (63.5 mm) using a 1/2 in. (13 mm) diameter masonry drill bit.
3Insert the concrete wall anchors (O) into the pilot holes and use a hammer to make sure the anchors are flush
with the concrete surface.
4Align the wall plate (A) with the anchors, insert the lag bolts (N) through the lag bolt washers (M), then
through the holes in the wall plate. Tighten the lag bolts only until they are firm against the wall plate.
CAUTION: Avoid potential injuries or property damage!
DO NOT over-tighten the lag bolts (N).
You’ll need
Top
Dessus
Vistasuperior
Top
Dessus
Vistasuperior
DX-TVM112Wall Plate Template • Gabarit de la plaque de montage • Plantilla de la placa de montaje
Note:For wood frame installations, use
astud nder to locate a wood stud rst.
Remarque: Pour des installations sur
desstructures en bois, utiliser d'abord un
localisateurde montants pour détecter
unmontant en bois.
Nota:para las instalaciones en marcos
demadera, use primero un localizador
deviga para ubicar las vigas de pared.
V113-0139
ToolsNeeded
Outilsnécessaires
Herramientasrequeridas
Needmoreinformation about your mount? Scan this QR code or visit www.dynexproducts.com.
Besoindeplus de renseignements au sujet du support de montage? Numériser ce code QR ou
allersurle site www.dynexproducts.com.
¿Necesitamásinformación sobre su soporte de montaje? Escanee este código QR o visite
www.dynexproducts.com.
P
2.5 in.
(63.5 mm)
* Minimum solid concrete thickness: 8 in. (203mm).
* Minimum concrete block size: 8 x 8 x 16 in. (203 x 203 x 406 mm).
The minimum distance between the top two fasteners cannot be less
than 2.865 in. (72.8 mm)
N(3)
Drill
1/2" masonry
drill bit 1/2" socket
wrench
Level
O (3)
Hammer
Wall plate (A)
Pencil
M(3)
Top
Dessus
Vistasuperior
Top
Dessus
Vistasuperior
DX-TVM112Wall Plate Template • Gabarit de la plaque de montage • Plantilla de la placa de montaje
Note:For wood frame installations, use
astud nder to locate a wood stud rst.
Remarque: Pour des installations sur
desstructures en bois, utiliser d'abord un
localisateurde montants pour détecter
unmontant en bois.
Nota:para las instalaciones en marcos
demadera, use primero un localizador
deviga para ubicar las vigas de pared.
V113-0139
ToolsNeeded
Outilsnécessaires
Herramientasrequeridas
Needmoreinformation about your mount? Scan this QR code or visit www.dynexproducts.com.
Besoindeplus de renseignements au sujet du support de montage? Numériser ce code QR ou
allersurle site www.dynexproducts.com.
¿Necesitamásinformación sobre su soporte de montaje? Escanee este código QR o visite
www.dynexproducts.com.
Wall plate template (P)Tape
DX-TVM112_13-0526_MAN_V4_EN-A4.fm Page 6 Friday, June 7, 2013 6:43 AM
