Dynex DX-WD1239 User manual

ASSEMBLY INSTRUCTIONS
DX-WD1239
TV Cart
Safety information and specifications ............2
Tools needed............................................................3
Package contents ...................................................3
Assembly instructions...........................................5

2DX-WD1239
Need help? Call 800-305-2204
Safety information and specifications
Warnings
• Do not let children climb on your TV cart or play near it. Your TV cart may tip over causing the TV or cart to
injure someone.
• When placing items on the shelves or the top of the TV cart, load the bottom shelf first and work up to the top
of your TV cart.
• Do not overload the shelves. They may break.
• Do not move your TV cart with items on the top or shelves. Your TV cart may tip over and injure someone.
Before you move your TV cart, unload starting with the top of your TV cart and working to the bottom shelf.
CAUTION:
This TV cart’s work surface is intended only for
use with a product not weighing more than 95
lbs. (43.09 kg) and having 42" wide flat-panel TV
dimensions that will permit it to sit evenly on your TV cart.
Using with other products, including products that weigh
more than the maximum weight allowed, may result in
instability, which may cause possible injury.
Maximum weight: 95 lbs. (43.09 kg)
Maximum screen size: 42"
Weight capacity (top of TV cart): 95 lbs. (43 kg)
Weight capacity (middle shelf): 25 lbs. (11 kg)
Weight capacity (lower shelf): 30 lbs (13 kg)
Overall dimensions: W × H × D
28.12 x 18.75 × 14.88 inches (71.45 × 47.6 × 37.8 cm)
Top of TV cart: W × D
28.12 × 14.88 inches (71.45 × 37.8 cm)
Usable upper shelf (shelf in middle position) :W × H × D
17.81 × 6.31 × 13.56 inches (45.2 × 16 × 34.3 cm)
Usable lower shelf (shelf in middle position): W × H × D
17.81 × 6.38 × 15.5 inches (45.2 × 16.2 × 39.4 cm)
14.88" (35.25 cm)
28.12" (71.45 cm)
18.75" (47.6cm)

3
DX-WD1239
Need help? Call 800-305-2204
Packagecontents
Package contents: hardware
Make sure you have all the hardware necessary to assemble your new TV cart:
Using a screw that is too long will cause damage your TV cart. Before beginning assembly, separate each
type of screw. Carefully study the screw table below. You can use the ruler at the bottom of the screw
table to measure screws. Pay close attention to the color of each screw.
You may receive extra hardware with your TV cart.
Letter Description Qty. Letter Description Qty.
P6Q16
Tools needed
Hammer
No. 2 Phillips screwdriver
Flatblade screwdriver
Caution: Do not
use an electric drill
or screwdriver
Label Hardware Qty.
I9
J9
K2
L2
Hidden cam
Cam dowel
Swivel caster
Non-swivel
caster
Label Hardware Qty.
M8
N4
O1
Metal pin
Rubber sleeve
Warning
label
Black 1 7/8" (47.75 mm) flat head screw
Black 9/16" (14.22 mm) large
head screw
10 20 30 40 50 60 70 80 90 100mm
1234in

4DX-WD1239
Need help? Call 800-305-2204
Package contents: parts
Note: All parts except for the stop molding (H) have a lettered sticker to make identifying parts easier.
Letter Description Qty. Letter Description Qty.
ARight end 1EBottom 1
BLeft end 1FAdjustable shelf 1
CUpright 1GValance 1
DTop 1HStop molding 1

5
DX-WD1239
Need help? Call 800-305-2204
Assembly instruc tions
Step1:
Assemble your TV cart on a carpeted floor or on the empty carton to avoid scratching your TV cart or the
floor.
Push nine hidden cams (I) into the ends (Aand B), upright (C), and top (D), then insert a cam dowel (J) into
each hidden cam.
You’ll need:
Do not tighten the hidden cams in this step.
Arrow
J(9)I(9)

6DX-WD1239
Need help? Call 800-305-2204
Step 2:
Insert two metal pins (M) into the two holes beside the hidden cam on the right end (A).
Repeat this step for the left end (B).
You’l l ne ed:
M(4)

7
DX-WD1239
Need help? Call 800-305-2204
Tightening hidden cams
In the remaining steps, use these illustrations for instructions on tightening hidden cams.
Warning: Risk of damage or injury. Hidden cams must be completely tightened. Hidden cams that are not
completely tightened will loosen, and parts may separate.
A hidden cam (I) has an arrow. When you insert the hidden cam, make sure that the arrow points toward the
hole in the side of the part you are inserting it into.
You’ll need:
Arrow Make sure that you turn the hidden
cam 210°. Note the position of the
arrow on the hidden cam.
Arrow
In the illustration below,
the hidden cam has not
been tightened enough.
210°
Flatblade screwdriver

8DX-WD1239
Need help? Call 800-305-2204
Step 3:
Fasten the stop molding (H) to the top (D). Use a flatblade screwdriver to tighten three hidden cams. See
“Tightening hidden cams” on page 7.
You’l l ne ed:
Unfinished
surface
Arrow
210°
Flatblade screwdriver

9
DX-WD1239
Need help? Call 800-305-2204
Step 4:
Fasten the left end (B) to the top (D). Use a flatblade screwdriver to tighten two hidden cams. See “Tightening
hidden cams” on page 7.
You’ll need:
Finished
edge
Arrow
210°
Flatblade screwdriver

10 DX-WD1239
Need help? Call 800-305-2204
Step 5:
Slide the valance (G) onto the two metal pins (M) in the left end (B).
Unfinished
surface
Finished
edge

11
DX-WD1239
Need help? Call 800-305-2204
Step 6:
Fasten the right end (A) to the top (D). Use a flatblade screwdriver to tighten two hidden cams. See
“Tightening hidden cams” on page 7.
Note: Make sure that the metal pins in the right end (A) insert into the holes in the valance (G).
You’ll need:
Finished
edge
Arrow
210°
Flatblade screwdriver

12 DX-WD1239
Need help? Call 800-305-2204
Step 7:
Fasten the upright (C) to the top (D). Use a flatblade screwdriver to tighten two hidden cams. See “Tightening
hidden cams” on page 7.
Fasten the bottom (E) to the ends (Aand B) and upright (C). Use a Phillips screwdriver and six black 1 7/8" flat
head screws (P).
You’ll need:
Screw holes
Unfinished
surface
Long finished edge
Finished edge
Arrow
210°
Flatblade screwdriver Phillips screwdriver P(6)

13
DX-WD1239
Need help? Call 800-305-2204
Step 8:
Fasten the swivel casters (K) and the non-swivel casters (L) to the bottom (E). Use a Phillips screwdriver and
16 black 9/16" large head screws (Q) (four screws per caster).
You’ll need:
The tabs on the
non-swivel casters (K)
must insert into these
holes.
Phillips screwdriver Q(16)

14 DX-WD1239
Need help? Call 800-305-2204
Step 9:
Carefully stand your TV cart upright.
Push the rubber sleeves (N) on the metal pins (N), then insert the metal pins into the hole locations of your
choice in the right end (A) and upright (C). Set the adjustable shelf (F) onto the metal pins (M).
Apply the warning label (O) to the top (D). You should be able to read the label when the TV is removed from
your TV cart. When the TV is in place, it should hide the label. Peel off the backing and apply the label as
shown.
Caution: This is a permanent label intended to last for the life of the product. Once applied, do not try to
remove it. You may damage the finish on the top.
You’ll need:
Metal pin
with
rubber
sleeve
95 lbs
(43 kg)
25 lbs
(11 kg)
30 lbs
(13 kg)
Warning: Never use this
furniture with a TV that is too
large or too heavy. Severe
injury or death can occur. The
TV and furniture will be
unstable and may tip.
• The TV must weigh less
than 95 lbs.
• The base of the TV must
be able to sit completely
on this shelf.
N(4)M(4)

15
DX-WD1239
Need help? Call 800-305-2204
Still need help?
For customer service, call: 800-305-2204 (U.S./Canada markets)
Distributed by Best Buy Purchasing, LLC
7601 Penn Avenue South, Richfield, MN USA 55423-3645
© 2011 BBY Solutions, Inc.
All rights reserved. DYNEX is a trademark of BBY Solutions, Inc. Registered in some countries. All other
products and brand names are trademarks of their respective owners.

www.dynexproducts.com [phone]
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave. South, Richfield, MN 55423 U.S.A.
© 2011 BBY Solutions, Inc.
All rights reserved.
DYNEX is a trademark of BBY Solutions, Inc. Registered in some countries. All other products and
brand names are trademarks of their respective owners.
11-0434
ENGLISH
Certificate of Conformity
1. This certificate applies to the Sauder
Woodworking Product identified by this
instruction booklet.
2. This certificate applies to the compliance of this
product with the CPSC Ban on Lead-Containing
Paint (16 CFR 1303).
3. This product was manufactured by:
Sauder Woodworking Company
502 Middle Street
Archbold, Ohio 43502
[phone]
4. Date of Manufacture: ____________
Lot number: 337300