E-ride Industries 2009 EXV2 User manual

2009 Model Owner Manual

Vehicle Registration
Register your e-ride vehicle on-line at www.e-ride.com. Click on warranty
vehicle registration, fill out the form, and click on the submit button. If you have no
access to the internet please contact the e-ride Industries Customer Assistance Center at
800-950-4351 to register.
By filling out this form, you are giving us information so we can contact you for
any further vehicle or service information that may become available.

e-ride Industries Page 1
Table of Contents
Heading Page
Introduction 2
General Specifications 5
Lighting 11
Driver Controls 16
Vehicle Operation 35
Maintenance 50
Transporting the Vehicle 71
Customer Assistance Information 72
Warranty Information 74
Vehicle Options___________________________________87

e-ride Industries Page 2
Section 1: Introduction
1.1 A Note to the Customer
Thank you for purchasing your zero emission, battery powered Neighborhood
Electric Vehicle (NEV) from e-ride Industries. Customer satisfaction and safety are the
primary concerns of e-ride Industries. For this reason, it is recommended that you take
the time to read through this entire manual for important information about the safe use
and maintenance of your electric vehicle.

e-ride Industries Page 3
1.2 About the Manual
This owner manual is designed to familiarize you with the safe and proper use of
your new e-ride vehicle. It will help you learn about the features, controls, and operation
of your new electric vehicle. It will also give you important information about
maintenance and the associated safety information. This manual is applicable to the
two e-ride Industries models: the two passenger EXV2 and the four passenger
EXV4.

e-ride Industries Page 4
1.3 Vehicle Identification
For both two and four passenger models, the vehicle identification number (VIN)
is found on the VIN/Certification Label. This label is located on the base of the driver’s
seat facing the door. The VIN contains information such as the model year, type,
GVWR, tire pressure, and other useful information. Please record the 17 character
vehicle identification number in the space below:
Vehicle Identification Number (VIN):

Date Purchased: ______/_____/______

e-ride Industries Page 5
Section 2: General Specifications
Specifications for:
2.1 e-ride Industries Flatbed Utility Vehicle (EXV2)
Curb weight 1,855 pounds
GVWR 3,000 pounds
Length 156 inches
Width 60 inches
Height 70 inches
Flatbed bed size 72 inches x 58 inches
Drive system voltage 72 volt

e-ride Industries Page 6
Batteries 8 volt lead acid – qty. 9
Drive Axle Gear reduced direct drive
Motor 72 volt DC
separately excited
(optional 72 volt AC)
Top Speed 25 miles per hour
Tires 14” street rated
Brakes Hydraulic front disc
and rear drum
Steering Rack & pinion
Chassis Riveted aluminum
Bumpers Steel front and rear

e-ride Industries Page 7
Suspension Independent front suspension,
leaf spring solid axle in rear
Speed Controller 72 volt with regenerative braking
(optional 72 volt AC)
Charger 72 volt DC charger
Charge time 8-12 hours depending on discharge
Charging energy requirements 220 volt AC for best charge and
110 volt AC for emergency use only
Lights Headlights w/bright, taillights, turn signals,
hazard lights, and brake lights

e-ride Industries Page 8
2.2 e-ride Industries Coach Transportation Vehicle (EXV4)
Curb weight 1,855 pounds
GVWR 3,000 pounds
Length 145 inches
Width 60 inches
Height 70 inches
Flatbed bed size 28 inches x 55 inches
Drive system voltage 72 volt
Batteries 8 volt lead acid – qty. 9
Drive Axle Gear reduced direct drive

e-ride Industries Page 9
Motor 72 volt DC separately excited
(optional 72 volt AC)
Top Speed 25 miles per hour
Tires 14” street rated
Brakes Hydraulic front disc and rear drum
Steering Rack & pinion
Chassis Riveted aluminum
Bumpers Steel front and rear
Suspension Independent front suspension,
leaf spring solid axle in rear
Speed Controller 72 volt with regenerative braking
(optional 72 volt AC)
Charger 72 volt DC charger

e-ride Industries Page 10
Charge time 8-12 hours depending on discharge
Charging energy requirements 220 volt AC for best charge and
110 volt AC for emergency use only
Lights Headlights w/bright, taillights, turn signals,
hazard lights, and brake lights

e-ride Industries Page 11
Section 3: Lighting
3.1 Locations
3.1.1 Headlights
The headlights are found in the front of the vehicle mounted into the front of the
hood. There are four total headlights that utilize a clear lens. The dim setting lights
are the center two and the outer two lights are the bright setting lights. The dim
setting operates with just the center two lights and all four lights are illuminated on
the bright setting. Headlights should be kept clean and in good operation at all times
as not to impair night visibility.

e-ride Industries Page 12
3.1.2 Front Parking Lights/ Turn Signals
These lights operate as both the front turn signals and the parking lights. They are
located in the front of the vehicle mounted into the front of the hood. They are the
rectangular amber colored lights located just below the headlights on either side of
the vehicle. They operate with the headlights turned on as well as flashing for the
corresponding turn signal and hazards.
3.1.3 Taillights/ Brake Lights/ Rear Turn Signals
These lights have three functions and are the red rectangular lights at the rear of
the vehicle mounted into the tail panel. These operate on their dim setting as the
taillights with the light (headlight) switch turned on. They flash with the
corresponding turn signal and hazards and also illuminate when the brake pedal is
pushed.

e-ride Industries Page 13
3.2 Headlight Bulb Replacement
1. Make sure the lights switch and key switch have been turned off.
2. Remove cover from the light by taking off the four nuts.
3. Remove the wire connector from the headlight.
4. Turn the bulb counter-clockwise and pull it straight out to remove it
from the housing.
5. To put back together, go through steps 2 – 4 in reverse order.

e-ride Industries Page 14
3.3 Taillight Bulb Replacement
1. Make sure the lights switch and key switch have been turned off.
2. Turn the socket counter-clockwise to release it from the housing.
3. Pull the bulb straight out to remove it from the socket.
4. To put back together, go through steps 2 and 3 in reverse order.

e-ride Industries Page 15
3.4 Flasher Replacement
1. Make sure the lights switch and key switch have been turned off.
2. Remove the console and dash assemblies. The flasher is located on the firewall to the
left of the wiper motor.
3. Remove it from its plug housing and replace.
4. To put back together, go through steps 2 and 3 in reverse order.
Note: The turn signals and hazards use the same flasher.

e-ride Industries Page 16
Section 4: Driver Controls
4.1 Digital Dash Display
The digital dash display is the large
flat screen monitor located in the center of
the dash between the selector switch and the
12 volt accessory power outlet. This display
shows multiple functions and includes all the
dash instrumentation.

e-ride Industries Page 17
4.1.1 Vehicle Speed
The display shows speed on a sweep dial of 0-35 miles per hour. It also displays
below the sweep dial a digital reading of the speed.
4.1.2 Battery Discharge Indicator (BDI)
The display shows the state of charge on a bar graph of 0-100 percent. When
battery percentage drops to 0 on the graph, there is 20 percent of battery capacity left. At
this point of discharge, the battery discharge indicator located to the lower left of the
graph will flash and the caution light located on the display to the right of the digital
screen will illuminate. (See section 5.3 Charging of this manual for the charging
procedure)

e-ride Industries Page 18
4.1.3 Odometer
The display shows the total miles on the vehicle. The miles are not resettable. On
the digital dash display, it is located at the bottom center of the screen.
4.1.4 Hour Meter
The display shows the total hours the key has been turned on. On the digital dash
display, it is located at the bottom right side of the screen. The hour meter is not
resettable.
4.1.5 Clock
The display shows the time of day. This is set by pressing the buttons located on
the display below the digital screen. On the digital dash display, it is located at the
bottom left side of the screen. To set the clock, press and hold the select button for 3
seconds and then release when the main menu appears. Press the up and down buttons to