Eastern Jungle Gym Classic Bench Setup guide

Owners & Instruction Manual
2021

1
1-800-752-9787
Customer Service available 9-5pm EST Mon-Fri call 1-800-752-9787
or Email-Inf[email protected]om

2

6
3
Site Location
Our exclusive leveling system was developed through more then 26
years of installation experience. This unique leveling system ensures
safe installation on un-level properties.
While your jungle gym will be level and safe some of the activities will be
affected by the sloping property (Diagram A ). If your swing beam is installed
downhill (or uphill), the swing position closest to the end will be lower to (or
further from the ground) (Diagrams A).
To determine play area size, it is recommended that you add six feet to the
jungle gym dimensions on all sides. However, besides swing beam side supports
and other low traffic areas it is not critical to have a six foot “play area”.
Installing a resilient surfacing under the jungle gym is always recommended and
can be done AFTER your jungle gym is installed.
A1 Level
Property Slope

4

Accessories Identification
5
1 @ SWING BEAM SBHG46120
Wood Identification Wood Swing
(2)
(1) Full Bucket
Swing
(1) Bench Swing
(4)
(4)
(4) Snap Hooks
(2
(2) Easy 1-2-3 Bracket
4 @ Side Support Part # SSP4496

6
Note: If you have purchased only the Eastern Jungle Gym hardware kit,
EJG recommends that the beam size should be 4x6x120”. The side
supports should be 4x4x96”.
Please prepare the swing beam using the dimensions shown in the
diagram below.
You will need a 1-3/8” x 8” Drill bit.
BUCKET SWING BENCH SWING
7/16” PILOT HOLE

Hardware Identification
H6
B3
W3/8 W5/16
7
H6- 3/8” x 6 ½” Hex Bolt
B3- 5/16” x 3” Lag Bolt
N- Nut
W 3/8” Washer
W 5/16” Washer
N

8

Note: Make sure swing
hangers are facing up.
Step #1 Swing Beam Assembly Wood Swing
Place swing hangers on beam as shown using hardware provided.
9
Step #2 Easy 1-2-3 Bracket Install Wood Swing
(8)-3/8 Hex Bolt (6½”)
(16)-3/8 Washer
(8)-3/8 Nut
(4)-Swing Hangers
Note: Please note
swing hanger
location on beam.
Layout SBHG46120 on the ground
with swing brackets facing up. Slide
Easy 1-2-3 Bracket onto beam.
Predrill (3)-1/4” pilot holes. Attach
bracket to post using B3 lag bolts.
Repeat on opposite sides.
3/8” Nut
3/8”
washer

Step #3-Post Install Wood Swing
10
Install (4)-SS4496 Posts into Easy 1-2-3
Bracket. Predrill (4)-1/4” pilot holes.
Install posts to bracket using B3 bolts.

Step #4- Swing Set Leveling Wood Swing
11
With the help of another person turn swing beam assembly
upright. Level swing beam as needed by digging the side
support legs into the ground.
Check with level
Two metal stakes are provided for added stability.
After swing beam is installed insert stakes into the
ground flush with support legs. Leave 6” exposed
and bolt to support using two B3 lag bolts.

Step #4- Install Accessories Wood Swing
12
Assemble wooden swing using hardware provided with swing. Hang
baby swing and wooden swing. Make sure chains are the same length
on each piece to ensure the swing is level.
10’
8’-6”
Add black and white drawing

13

14
Customer Service available 9-5pm EST Mon-Fri call 1-800-752-9787

15

16