Eastern Jungle Gym ULTIMATE Setup guide

Owners & Instruction
Manual
This instruction booklet is to be used exclusively for Eastern Jungle Gym
customers only. It is not to be handed out to the general public. Any duplication of
this booklet will be subject to copyright protection and federal laws.
“Creating Childhood Memories”
R
ULTIMATE
last revised 3/30/2016

IMPORTANT INFORMATION
PLEASE READ...
If you have any missing parts or damaged material or are
having trouble installing your new Eastern Jungle Gym product.
Please call Eastern Jungle Gym directly.
or Email - [email protected]
It is important for you to go through your boxes and check
all material, hardware and wood prior to building. So that
you can familiarize yourself with the material. Also it is very
helpful to read and look over this instruction booklet. This will
help insure you build your Jungle Gym properly, safely and more efficiently.
A little time now can save you time when your building!
“Creating Childhood Memories”
R
2
Customer Service available 9-5pm EST Mon-Fri call 877-543-4969

Play Safely Instructions
1) Do not let children play on your Eastern Jungle Gym product until it is fully and safely
assembled.
2) Go over all safety points with children prior to letting them play.
3) Adult supervision is required for children of all ages.
4) Warn children from playing, walking or running in front of or behind any moving objects.
5) Warn children from twisting on the swings this can weaken product and cause it to
break.
6) Warn Children not to attach any objects to the Swing Set such as clothes lines, jump
ropes or any other rope this may cause strangulation hazards.
7) Warn children from pushing empty swing equipment, twisting chain or ropes or jumping
off any moving swing equipment or deck. DO NOT use any part of the swing set in a
manner that it is not intended for.
8) Warn children from playing on swing set if it is wet this can cause swing set to become
slippery.
9) Warn children only one person on a swing at a time.
10) Warn children that anything other than sitting on swings is dangerous and can cause
serious injury. Never stand or kneel on swings.
11) Warn children to not loop chains over any object this can cause the chain to weaken.
12) Children should not wear any loose clothing while playing such as scarfs and hats with
strings or any other very baggy clothes. This can cause tripping hazzards.
Choosing a Location to
Build your Eastern Jungle Gym
When selecting a your Eastern Jungle Gym location site keep in mind the child’s safety.
Here are some recommendations to help you create a safe play area.
1) The swing set should be located on fairly level ground. The stationary components such
as ladders, rock walls and slides are required to be a minimum of 6 feet from any
obstruction such as buildings, trees, rock wall, clotheslines, fences and overhead
branches. Any swinging equipment is also required to be a minimum distance twice the
height of the swing beam away from these obstructions or structures as well.
2) Do not locate Swing Set on asphalt, concrete, packed earth or other hard surfaces.
Now that you have located a safe area to build your Swing Set you are ready to begin.
“Creating Childhood Memories”
R
3

Tools Required
#2 Square Head Screwdriver and bit
Medium Phillips Head Screwdriver and bit
7/16” Standard Socket
1/2” Standard Socket
9/16 Standard Deep Well Socket
Standard Socket Wrench / Electric Impact Gun
Electric Drill
9/16” Box Wrench
1/4” Pilot Drill Bit
7/8” Countersink Drill Bit
Tape Measure
Carpenters Level
Claw Hammer
Razor Knife
Step Ladder
Safety Glasses
Assembly Safety Guidelines
Maintenance Instructions
1) Keep all children away from assembly area. Power tools and other dangerous
equipment will be needed. Many parts are heavy and could seriously injure a child.
2) Your ready to start your assembly process. You will need at least two adults to
safely and easily assemble your Eastern Jungle Gym.
3) Wear safety glasses when drilling out wood to protect your eyes from flying
wood clips.
4) Make sure all lag bolts and nuts are tightened and secured completely.
5) After throughly reading all your information, and have located your swing set
site. Carefully unpack all your parts. NOTE: keep check list close by. Remember
that a little time familiarizing your self with the parts and instructions before you
begin will help you avoid mistakes and save time later.
Here are some maintenance tips that must be done to ensure safe play.
1) At the beginning of each play season look over swing set: check nut, bolts,
screws and tighten as needed. Look over all components such as swing seats,
slides, chains, ladders and wood components for deterioration or sharp edges and
replace if necessary.
2)Oil all metal components such as swing hangers and tire swing hangers.
3)Spot sand any areas that are checking or splintering and check for broken parts
and replace if necessary.
4) We recommend on a yearly basis, to coat your swing set with a sealant. You
should look over set to make sure it does not need spot sand first. This will help
preserve the natural beauty and characteristics of the wood. Be sure to use non
toxic sealants.
“Creating Childhood Memories”
R
4

Hardware Identification
(6) Spring Clips
(6) Heavy Duty
Swing Hangers
(7) Ladder Rungs
Bag of
Rocks with Hardware
(2) Green
Sling Swings
Safety Grab
Handles
(3) Sections
Rope
(1) Ring Trap
Combo
Items not shown:
1 - Tent top
1 - Binoculars
1 - Captains Ships Wheel
(1) Swing Beam
Support Brace
“Creating Childhood Memories”
R
7
Scoop Slide

SPECIAL NOTE
BEFORE BEGINNING YOUR
ASSEMBLY:
All Recessed holes must be
piloted with 1/4” drill bit to help
minimize splintering.
All lag bolts must be accompanied with
a washer before driving in lag bolt.
Now you are ready to begin assembling!
“Creating Childhood Memories”
R
9

Ultimate GROUND SUPPORT BASE Step #1
Measure 3½” and 5” in from each corner of both
Gs2655’s (as shown in photo).
Stand up ground supports on end and install with
1 - 3” lag through GS2655 into R2655. Use the
3½” and 5” marks you made earlier as guides.
NOTE: The counter sink holes in R2655 should
face the inside of box. The counter sink holes on
Gs2655 should face outside of box.
Measure from corner to corner on each side of
ground support base. Make sure your
measurements are the same. This will square of
base.
R2655
Gs2655
3½ ”
5”
R2655
R2655
G
S
2
6
5
5
G
S
2
6
5
5
R2655
R2655
G
S
2
6
5
5
G
S
6
4
5
5
1 - 3” lag in
each corner
Countersink
Holes
Countersink
Holes
Layout ground support base boards.
2 - Gs2655
2 - R2655
(as shown in the photo).
10

Layout 4 - P44114 clubhouse post (as shown in the
photo).
Measure in 46½” from one side of P44114 posts
and draw a line (as shown in the photo). Do this
to all 4 posts.
NOTE: Mark the longer side with an X.
Now place PT246 floor teak supports over “X” with
edge on line drawn. Install with 2 - 3” lags.
Continue on all 4 posts.
NOTE: The 46½” side is the TOP of post mark
with an “O”.
Post complete continue to next page for post
installation on clubhouse.
X
OOO O
XX
X
P44114
PT246
46½ ”
46½ ”
Ultimate POSTS Assembly Step #2
11

Position first completed 4x4
post into the lowest corner of
the ground support base (as
per you landscape). Than level
both sides.
NOTE: Notice the position of
post is actually on the outside
of the base. Also the 2x4 teak
is facing inside of base.
NOTE: The “O” mark is at the
top.
After leveling, fasten 4x4 post to ground
support base using 4 - 3” lags (as shown
in photo). First post completed (as shown
in photo).
Using first post as a guide place level on PT246 floor teak mounted on post. Dig down second post until
level with first post. Again fasten with 4 - 3” lags in holes provided. Continue this process until all 4 post
are fastened.
NOTE: Make sure the “O” is always on the top of post and 2x4 teak is facing inside of clubhouse.
NOTE: If installing on
unlevel ground place first
post in lowest corner of
ground support base and
dig the remaining 3 posts
in ground as needed to
bring level with first post.
P
O
S
T
P
O
S
T
PT246
Unlevel Ground
Level Floor Supports
O
O
O
O
O
O
O
Ultimate FLOOR Assembly Setup #4
12

FT2455
F
B
5
4
6
4
8
F
B
5
4
6
4
8
Ultimate FLOOR Assembly Setup #4
Measure 3½” and 5” in from each
corner of both Gs2655’s (as
shown in photo).
Start decking your floor using
FB54648 one on each side of
floor frame (as shown in photo).
Install using 2” screws.
Continue decking your floor using
FB54648 until it is completed (as
shown in photo). Install using 2”
screws.
Turn floor over and screw
FT2455 to floor decking using 2”
screws (as shown in photo).
Layout floor joists
2 - Fj2655,
2 - R2655
(as shown in the photo).
R2655
Fj2655
3½ ”
5”
1 - 3” lag in
each side
R2455
FT2455
F
J
2
6
5
5
Stand up floor joist on end and install
with 1 - 3” lag through Fj2655 into
R6455. Use the 3½” and 5” marks
you made earlier as guides.
NOTE: The counter sink holes in
R2655 should face the inside of box.
The counter sink holes on Fj2655
should face outside of box.
NOTE: Center countersink hole on
Fj2655 should be at the top of joist
see photo to the left.
Install Floor teak FT2455 using hole provided with 1 - 3” lag. FT2455
will run in the flat and be flush with top of Fj2655. Make sure the
countersink screw holes on FT2455 are facing the ground.
Fj2655
FT2455
FT2455
R2655
R2655
F
J
2
6
5
5
F
J
2
6
5
5
1 - 3” lag in
each corner
Countersink
Holes
Countersink
Holes
R2655
R2655
F
J
2
6
5
5
F
J
2
6
5
5
13

FLOOR Installation Step #5
Place floor on post teaks that you leveled earlier.
At this point all four post and floor should be level.
NOTE: Make sure floor orientation match ground
support base orientation when placing floor on
post.
Pull post tight to floor making sure that the
floor is resting on 2x4 teaks. Now install
with 2 - 3” lags in each corner.
From under the clubhouse lag the floor
into post in all four corners using 2 - 3”
lags.
Clubhouse floor is completed!
14

Ultimate SLIDE WALL installation Step #6
Install top wall rail, WR2496
flush with top of post using 2 - 3”
lags on each side.
NOTE: Rail should extend 20½ ”
from post on each side.
Place bottom wall rail, R2429 on
floor and install into left post
using 2 - 3” lags. Make sure the
slide opening is on the right. Install tent support TS4484 to
the center of WR2496 and to the
side of R2429. Using 2 - 3” lags
on top and bottom. Make sure
you level your tent support 4x4
before installing lags.
SLIDE Wall
WR2496
R2429
20½”
Layout 3 - WB54440 wall boards
on the inside of clubhouse against
rails just installed.
Measure 3½” in from TS4484 tent
support and install your first wall
board With 1-3/4” screws. Now
measure 3½” in from P4414 post
and install second wall board with
1-3/4” screws . Now install your last
wall board in center of the two wall
boards with 1-3/4” screws.
NOTE: 3½” Openings off post and
tent support are important to be
correct for this is the location of
monkey bars to be install later.
3½”
3½”
20½”
T
S
4
4
8
4
15

Ultimate SOLID WALL installation Step #7
Place bottom wall rail, WR2455 on floor and
install to both posts using 2 - 3” lags on each
side.
Solid Wall
WR2455
Install top wall rail, WR2496 flush with top of
post using
2 - 3” lags on each side.
NOTE: Rail should extend 20½” from posts
WR2496
20½”
20½”
Install tent support, TS4484 to the
center of WR2496 and to the
center of WR2455. Using 2 - 3”
lags top and bottom. Make sure
you level your tent support 4x4
before installing lags.
Layout 6 - WB54440 wall boards
on the inside of clubhouse
against rails just installed.
Measure 3½” in from TS4484 tent
support on each side and install
your first two wall boards With 1-3/4”
screws. Now measure 3½” in from
each P44114 post and install third
and fourth wall boards with 1-3/4”
screws . Now install your last two
wall boards in center of the other
two wall boards.
S
4
4
8
4
S
4
4
8
4
3” lags
3” lags
W
B
5
4
4
4
0
W
B
5
4
4
4
0
3½”
3½”
16

Ultimate ACTIVITY WALL #1 installation Step #8
Activity Wall #1
R2455
Place rail R2455 from inside clubhouse
flush with top of post and install with 2-3”
lags on each side.
Place wall board Wb54440
from outside of clubhouse
3½” in from post and flush
with bottom of floor and rail
just installed (as shown in
photo). Install with 2 - 1-3/4”
screws on top and bottom.
Place second wall board
Wb54446 from outside of
clubhouse 3½” in from post
and flush with bottom of floor
and rail just installed (as
shown in photo). Install with
2 1-3/4” screws on top and
Place wall board, Gh2446
from outside of clubhouse
1½” in from wall board,
Wb54446 and flush with
bottom of floor and rail just
installed (as shown in photo).
Install with 2 - 2” lags on top
and bottom.
Place wall board, GH2446
from outside of clubhouse
1½” in from wall board,
Wb54446 and flush with
bottom of floor and rail just
installed (as shown in photo).
Install with 2 - 2” lags on top
and bottom.
Activity Wall #1 Complete! Now time
to assemble and install your Rock
Wall!
W
B
5
4
4
4
0
W
B
5
4
4
4
0
W
B
5
4
4
4
6
G
H
2
4
4
6
G
H
2
4
4
6
17

Ultimate ROCK WALL assembly Step #9
Layout 2 - RWJ2484 Rock Wall
joists (as shown in the photo).
NOTE: Counter sink holes face
each other.
R
W
J
2
4
8
4
R
W
J
2
4
8
4
Counter sink holes
face each other
Start decking your rock wall
using FB54648. Start right
above the counter sink holes on
the RWJ2484 Rock Wall joist
(as shown in photo). Using
2 - 2” screws on each side.
After you have located your
desired positions. Mark with a
pencil where to drill holes.
After you have marked desire
location remove rocks and drill
holes using a 3/8 drill bit.
After you have drilled out all the
holes you can start rock
installation.
Continue decking your rock wall
using FB54648 until it is
completed (as shown in photo).
Install using 2” screws. The
RWJ2484 will extend past
decking.
Place 12 rock hand holds in
desired location on decking of
rock wall.
Place a set of T-nuts into the
back of rock wall. Now place rock on decking
and insert washer than lock
washer and than bolt in place.
Tighten using a ½” socket.
Continue until all eight rock
hand holds are completed. 18
After decking is installed
turn over and attach RWT2480
flush with bottom of decking as
pictured. Fasten with 2” screws.

Place rock wall into back opening.
Hold top of rock wall flush with top
of floor (as shown in photo).
From under the clubhouse
fasten rock wall to post
using
1 - 3” lag on each side (as
shown in photo). Rock wall complete!
Ultimate ROCK WALL installation Step #10
Layout Sa4494 swing arm with counter sink holes
facing up. (as shown in photo).
Place swing hangers on beam using hardware
provided. Notice how the hangers are mounted on
swing arm. (as shown in photo).
4 @ 3/8” Hex Bolt
8 @ 3/8” Washer
4 @ 3/8” Lock Nut
2 @ Swing Hangers
Mount swing arm onto clubhouse above
rock wall using 2 - 5” lags on each side.
The swing arm gets mounted under the
wall top rails (as shown in photo). Swing
Arm should point out the same direction
as the slide wall opening.
Slide Wall
OPTIONAL SWING ARM Assembly Step #11
19

Ladder Side WALL Installation Step #12
Activity Wall #2
R2455
Place wall board, R2455 from inside
clubhouse flush with top of post and
fasten with 2-3” lags on each side.
R2429
Place ½ wall rail R2429 flush
with edge of post and fasten
with 2-3” lags.
Place clubhouse center rail
CR4446 flush with top of rail
and fasten with 2-3” lags.
Fasten clubhouse center rail
CR4446 flush with 2-3” lags
from under deck.
W
B
5
4
4
4
0
Place wall board Wb54440
from outside of clubhouse
3½” in from post and flush
with bottom of floor and rail
just installed (as shown in
photo). Install with 2 1-3/4”
screws on top and bottom.
20

Ultimate LADDER Assembly Step #13
Counter sink holes
face each other
6”
17”
28”
39”
50”
61”
72”
Counter sink holes
face each other
6”
Layout 2 - LS4481 ladder rails and
7 - Ladder rungs
NOTE: Counter sink holes face
each other.
Measure from the top which is the
counter sink holes side. Using the
measurements above (as shown in
the photo).
Screw the ladder rungs into
ladder using 1½” Screws. (as
shown in the photo).
Measurements are to center of
rungs. Continue until all 7 rungs
are screwed in.
Ladder is now complete! Install JB4458 Jacobs Ladder
Bottom rail to the ladder. Make
sure to leave 3½” overhang on the
right side of ladder and flush with
the bottom.
Notice all holes
are facing UP.
Jb4458
3½”
Using holes provided install
2 - 5” lags on each side.
3½”
Ultimate LADDER Installation Step #14
Place ladder into front
opening. Hold top of
ladder flush with top
of floor (as shown in
photo). Jacobs
Ladder Bottom rail
should stick out
towards the slide wall
opening.
NOTE: Holes for
Jacob’s Ladder face
Slide Wall
Opening
Using 2 - 5” Lag bolts. Bolt the ladder
into Post using holes provides (As
shown in picture).
L
S
4
4
8
1
L
S
4
4
8
1
21

Ultimate JACOB’S LADDER TOP RAIL Step #15
Mount JT4484 Jacobs Ladder top rail onto
clubhouse using 2 - 5” lags on each side.
The JT4484 gets mounted under the wall
top rails (as shown in photo). Through
holes should be facing the ground and run
parallel with the bottom rail mounted on
the ladder.
NOTE: If installing Wood Roof ADD ON Skip
Step#17 and go to Wood Roof ADD ON manual.
Tent Top Rail
Mount first TR2464 tent rail across
the wall top rails. Above the rock
wall. Install with 1 - 3” lag on each
side .(as shown in photo)
Mount second TR2464 tent rail
across the wall top rails. Above
the ladder. Install with 1 - 3” lag
on each side
.
(as shown in
photo)
Mount Ts2464 Tent Support on top
of TS4484 install with 1 - 3” lag on
each side (as shown in photo).
Jacobs ladder rope to be installed
on the next page.
22

Ultimate TENT TOP Step #17
Drape tent top over Ts2464
tent support than over and
under TR2464 tent rail. Install
with 4 - 2” screws in holes
provided on tent top
.
(as shown
in photo)
Do the same thing to the other
side of tent top screw into
Tr2464 tent rail using 4 - 2”
screws .(as shown in photo)
JACOB’S LADDER Step #18
Layout 7 - JD2426 Jacob Ladder
Rungs and 3 - ropes
.
(as shown in photo)
Thread rope through Jacobs
Ladder top rail JT4484 and knot
on the top .(as shown in photo)
Thread 3 ropes through first
JD2426 Jacobs Ladder rung and
tie a knot approximately 12” down
from top rail .(as shown in photo)
Continue
installing other 7
JD2426 Jacob
Ladder Rungs
using the same
process all the
way down the
ropes
.
(as shown
in photo) Place ropes through JB4458
Jacobs Ladder Bottom Rail pull
tight and tie knots
. Cut off any excess rope.
(as shown in
photo)
23