EasternCCTV IP-5VP5M32VF User manual

Package
Overview
Installation
1
2
3
4
2
13
Thank you for purchasing our product. There may be several
technically incorrect places or printing errors in this manual.
The updates will be added into the new version of this manual.
We will readily improve or update the products or procedures
described in the manual. The content is subject to change
without notice.
Warning and Caution
■ If the product does not work properly, please contact your dealer
or the nearest service center. Never attempt to disassemble the
camera yourself. (We shall not be responsible for any problems
caused by unauthorized repair or maintenance.)
■ Keep away from liquid while in use.
■ In the use of the product, you must be strict compliance with the
electrical safety regulations of the nation and region. When the product
is mounted on wall or ceiling, the device shall be firmly fixed.
■ Do not use camera beyond specified voltage range.
■ Do not drop the camera or subject it to physical shock.
■ Avoid touching the camera lens.
■ If cleaning is necessary, please use clean cloth to wipe it gently.
If the device will not be used for a long time, please cover the lens
cap to protect the device from dirt.
■ Do not aim the camera at the sun or extra bright place.
■ Do not place the camera in extremely hot, cold (the operating
temperature shall be -20˚C~50˚C), dusty or damp locations, and do
not expose it to high electromagnetism radiation.
■ To avoid heat accumulation, good ventilation is required for
operating environment.
■ A few parts of the device shall be replaced regularly according
to their average enduring time.
Quick Start Guide
Network Camera
Camera Quick start guide
CD Water-proof cap Plastic plug ×4
Drill template
Sponge Screwdriver
4 tapping screws PA 4×25
enough to withstand 3 times the weight of the camera. Please install
and use the camera in the dry environment. You'd better install back
the lower dome less than 4 hours after removing it. The mounting
steps are as follows:
① Loosen the screws to open the lower dome and then loosen the
lock screw to remove the mounting base.
Before start, please make sure that the wall or ceiling is strong
② Attach the drill template to the place where you want to fix the camera
and then drill 4 screw holes and 1 cable hole (if you want to route the
cables through the mounting base) according to the drill template.
Lock Screw
Lower Dome
∅6
∅148
∅22
88 mm
89mm
CVBS&DC
IN cables
Network Cab le
8
910
RESET
TF
LINK DC
IN
CVBS
1
2
3
4
5
6
7
ALM-COM
ALM-NO
ALM-IN
ALM-GND
RS485T+
RS485T-
Microphone Cable
Headphone Cable TF Card Slot
Reset Hole
CVBS/DC IN port for testing
Alarm Input/Output
RS485 Cable
Video Output
Network Cable
Power Cable
1
2
3
5
7
9
4
6
8
10
* 1 It is recommended to install the water-proof cap for network cable connection.
* 2 If the switch is used to connect the camera, DC12V power supply
is not required.
PoE network
① Loosen the nut from the main element.
② Run the network cable (without RJ 45 connector) through the
both elements. Then crimp the cable with RJ 45 connector.
③ Connect the cable to the hermetic connector. Then tighten the
nut and the main cover.
●
Alarm Input: Join the grounding ends of the sensor and the camera
and then connect the signal cable of the sensor to the alarm input
port of the camera.
Alarm Output: Loosen the screws in the alarm output port. Then
insert the signal wires of the alarm output devices into the port of
NO and COM separately. Finally tighten the screws. Some of the
external alarm output devices need the power supply.
● Connecting Network Cable
Alarm Connection

IE Network Connection
5
MENU
MENU
IPC
IPC
Network Cable Network Cable
Network Cable
Switch
Router Computer
Computer
● Access the camera through IP-Tool
Here we take accessing IP camera via LAN for example. In LAN,
there are two ways to access. 1. Access through IP-Tool;
2. Directly Access through IE Browser
① Make sure that the camera and the PC are well connected via LAN.
② Find the IP-Tool from the CD and then install it in the computer.
After that, run the IP-Tool as shown below.
Device N etwor k Search
Immedia te Re fre sh
name
name
name
IPC
IPC
IPC
unkn ow n
unkn ow n
unkn ow n
192.168.226.201
192. 16 8.1 .2
192. 16 8.1 .3
80
80
80
9008
9008
9008
255. 25 5.
255.255.
255. 25 5.
Modi fy N etw or k Par am eter
Mac Add re ss
IP Addres s
Modi fy
CE :98 : 23 : 75 :3 5 :2 2
192 .168 . 226 . 201
255 . 25 5 . 25 5 . 0
192 .168 . 226 . 1
i
Tip : Enter t he a dmi ni strat or pass wo rd, and
then m od ify t he n etw or k param eters .
Total De vi ce: 3 Loca l IP Ad dr ess :1 92.168.1.4S ub net Mas k:255 .25 5.255.0 Gate wa y: 19 2.1 68.1.1 D NS：210.2 1.196.6
Devi ce N ame Devi ce Ty pe IP Addres s Http P or t Data P or t Sub ne t Prod uc t Mod el
About
Subn et M ask
Gate wa y
Restore IPC Default Configuration
③ Modify the IP address. The default IP address of this camera is
192.168.226.201. Click the information of the camera listed in the
above table to show the network information on the right hand.
Modify the IP address and gateway of the camera and make sure its
network address is in the same local network segment as that of the
computer. Please modify the IP address of your device according
to the practical situation.
Mac Address
IP Addres s
Modify Network Parameter
Modify
CE :98 :23 :75 :35 :22
192 .168 . 1 . 201
255 . 255 . 255 . 0
192 .168 . 1 . 1
Subnet Mask
Gateway
For example, the IP address of your computer is 192.168.1.4. So the
IP address of the camera shall be changed to 192.168.1.X. After
modification, please input the password of the administrator and click
“Modify” button to modify the setting.
The default password of the administrator is “123456”.
④ Double-click the IP address and then the system will pop up the IE
browser to connect IP-CAM. After downloading Active X control, a
login window will pop up. Input the user name and password to login.
● Directly Access Through IE
The default network settings are as shown below:
IP address: 192.168.226.201 HTTP:80
Subnet Mask: 255.255.255.0 Data Port:9008
Gateway: 192.168.226.1
You may use the above default settings when you log in the camera
for the first time.
① Set the IP address of the PC and make sure the network segment
should be as the same as the default settings of IP-CAM. Open the
network and share center. Click “Local Area Connection” to pop up
the following window. Select “Properties” and then select Internet
protocol according to the actual situation (for example: IPv4).
Next, click “Properties” button to set the network of the PC.
② Open the IE browser and input the default address of IP-CAM
and confirm. The IE browser will download Active X control
automatically.
③ After downloading Active X control, the login dialog box will
pop up.
④ Input the default username and password and then enter to view.
450043000260 A1
The default username is ad min; the default password is 123456.
③Route and connect these cables.
the ceiling or wall with screws.
Then secure the mounting base to
④ Fix the camera to the mounting base with the lock screw.
Sponge
Mounting Base
⑤ Three-axis adjustment. Before adjustment, preview the image of the
camera on a monitor and then adjust the camera according to the
figure below to get an optimum angle.
⑥ Adjust the Focus and Zoom screw to get a clear image (if your camera
is fixed lens, please skip this step).
Focus
Zoom
Rotation 0°~360°
Pan 0°~360°
Tilt 0°~77°
⑦ Install the lower dome back to the camera with the screws and
remove the protection film softly to complete the installation.