Eastsign MOT-M User manual

User Manual
Eastsign
MOTM20210302
Eastsign
Rotary Heat Press MOT-M
User Manual

Eastsign
ROTARY HEAT PRESS MOT-M USER MANUAL
Content
1. Information..............................................................................................................................................1
2. Safety Instruction.....................................................................................................................................2
2.1 Safety parts...............................................................................................................................................2
2.2 Warning Sign ............................................................................................................................................2
2.3 Safety Tips ................................................................................................................................................3
3. Specifications...........................................................................................................................................5
3.1 Specifications of the Machine..................................................................................................................5
3.2 Nameplate................................................................................................................................................6
4. Structure..................................................................................................................................................7
4.1 Explanation of appearance and all parts..................................................................................................7
4.2 Configuration of left cabinet ....................................................................................................................9
4.3 Configuration of right cabinet ..................................................................................................................9
4.4 Power box...............................................................................................................................................10
4.5 Accessories list .......................................................................................................................................11
5. Installation.............................................................................................................................................13
5.1 Unpacking...............................................................................................................................................13
5.2 Installation of worktable ........................................................................................................................13
5.3 Notice.....................................................................................................................................................14
6. Function.................................................................................................................................................15
7. Operation Guide .................................................................................................................................... 16
8. Notice for operation............................................................................................................................... 17
8.1 Adjustment to blanket tracking..............................................................................................................17
8.2 Noise ......................................................................................................................................................17
8.3 Cleaning..................................................................................................................................................17
8.4 Lubricating..............................................................................................................................................17
8.5 Blanket....................................................................................................................................................17
8.6 Changing of oil........................................................................................................................................18
9. Sketch up of Processing..........................................................................................................................20
9.1 Transfer of Garment in sheets................................................................................................................20
9.2 Transfer of both picture paper and fabric in rolls...................................................................................20
9.3 Transfer of fabric in rolls.........................................................................................................................21
9.4 Transfer of picture paper in sheets.........................................................................................................21
10. Circuit Diagram .................................................................................................................................... 22
11. Trouble Shooting.................................................................................................................................. 23
Warranty ...................................................................................................................................................24
Limitation of liability.................................................................................................................................. 25
Contact us.................................................................................................................................................. 26

Eastsign
ROTARY HEAT PRESS MOT-M USER MANUAL
1
1. Information
Rotary Heat Press MOT-1742M is developed on the basis of continuous feedback from end users and market
requirements. It is the most advanced equipment for cotton cold transferring. It is capable of flat transfer for
clothes pieces, transfer in roll to roll and cold transfer for cotton materials. Moreover, the machine occupies
small workplace. It reduces expenses in terms of power and labor.
There are many merits of MOT series machine as below.
1. Most of shafts of the machine were processed by CNC laser cutting system precisely, which means all
shafts are equipping at parallel. It enables the ultra-long transfer without tracking.
2. The heating roller is equipped in double layers of heat insulation, which means it saves about 30% to 40%
energy consumption comparing with other similar machines.
3. The chosen balance shafts in 87mm diameter which processed with CNC technique which keeps it rigid
and prevents it from deforming. Thus, transfer paper does not curl and ripple pattern doesn’t appear on
media.
4. Air pressure system helps transfer with vivid color and definition as good as the heat pressing transfer
machine. It also has high productivity of roll to roll system.
5. The machine is designed to feed materials from upper position, which keeps fabric feeding precisely and
lower the fault rate in process.

Eastsign
ROTARY HEAT PRESS MOT-M USER MANUAL
2
2. Safety Instruction
Before the operation, please read the safety instruction carefully to fully understand the machine’s primary
structure, function, and operation method. If conditions permit, the training to the operators is required, and
the operators, passing the examination, are allowed to operate and maintain. During the operation and
maintenance, please pay attention to the warning signs, pasted to the equipment, and improve the safety
awareness to prevent the accidents and to guarantee operator’s personnel safety.
2.1 Safety parts
2.1.1 Heat switch and Power switch
Heat switch and Power switch both are on the control panel. Press the heat power to stop the heating
immediately. Turn off the power button; the machine can not get the power for heating, but the machine can
get power for revolving the motor.
2.1.2 Separating blanket Switch
When the heat transfer finishes its working, turn off heating and keep motor rotating until the temp decline
under 80 ℃to prevent the blanket from burning.
2.1.3 Heating Roller
Following heating, the surface temperature of the heating roller could be up to over 240°C. While it is
heating, please don’t touch the roller surface with any part of the body to avoid crushing or burning. When the
machine is heating and operating, the operators shall be present to avoid the roller damages or the fire due to
the overheating.
2.2 Warning Sign
Please pay attention to the following warning signs. The cases shown in the signs are likely to cause machine
damages or injuries of the operators.
Anti-grinding
This sign is shown at the junction of the upper and lower drive
rollers, respectively at the both sides of the machine front. The
rubber roller in operation is relative dangerous. Please don’t let
your hand, clothes, hair or other parts of your body touch it to
avoid incident.

Eastsign
ROTARY HEAT PRESS MOT-M USER MANUAL
3
High Voltage
This sign is shown at the inner flank of the box.
High Voltage! Don’t touch to avoid electric shock.
Chain
This sign is shown at the inner flank of the left box.
Please don’t let your hand, clothes, hair or other parts of your
body
touch the chain in operation to avoid injury.
Burning Prevention
This sign is shown at front of cabinet near the heating oil drum.
The oil drum with black Teflon coating is the heating component,
so don’t touch it. When the power is off, oil drum requires enough
time for heat output. Don’t touch it immediately to avoid burning
incident.
2.3 Safety Tips
1. The electrical power source, used for the equipment must be in line with the type, designated by the
nameplate. The earthing must be accurate and reliable (equipment with three-terminal polarized plus
plug not allowed to change the function of the earth electrode freely).
2. When the equipment is operating normally, the surface temperature of the heating roller is very high,
and please don’t touch it with you hand.
3. When open the box to exam and fix of the equipment, the power must be shut off to avoid electric shock
or mechanical wounding incidents. When the transfer work has been finished the power should be cut off
too.
4. Don’t place the power lead on the walkway or pile up good on the lead. Strictly prevent the power lead

Eastsign
ROTARY HEAT PRESS MOT-M USER MANUAL
4
from rolling depression by the vehicles.
5. Mounting card and transducer in the box should be kept clean to avoid metallic conduction material such
as dust falling into. Don’t open the protective covering to avoid the electric shock.
6. The working place should be dry and well ventilated. Please stay away from the water or the damp place
when use the equipment. Don’t pile up the inflammable or explosive materials near to the equipment.
7. Don’t put tools or other sundries, such as screwdriver, screw nail and nut etc. at the worktable, upper
surface of the right box and other parts of the machine, to avoid falling into the rotating rollers, causing
damages to the machine.
8. Don’t wash the machine with water to avoid the short circuit, electric shock and the equipment
corrosion.

Eastsign
ROTARY HEAT PRESS MOT-M USER MANUAL
5
3. Specifications
3.1 Specifications of the Machine
Model
MOT-1742M
MOT-2742M
MOT-3242M
Cylinder
Oil-Heated, 50% Full
Voltage
3 phase, 220V / 380V / 480V
Heating Power
26kW
41kW
48kW
Heating
Elements
15
27
33
Diameter of Drum
420mm or 16.5" (Available in 600mm/800mm), Double Layer
Transfer Speed
1.5m-2.5m/min
Max Temperature
240°C or 464°F
Transfer Width
1600mm or 63"
2500mm or 98"
3150mm or 124"
Felt Width
1700mm or 67"
2600mm or 102"
3250mm or 128"
Process Path
Feeding in through Top of The Drum
Roll-to-Roll
Y
Piece-to-Piece
Y
Feeding Rollers
3
Collecting Rollers
2
Working Table
Yes, But glass will not be included
Machine
Dimension
2450 x 985 x 1320mm
96" x 39" x 51"
3290 x 985 x 1320mm
130" x 39" x 51"
4010 x 985 x 1320mm
158" x 39" x 51"
Working Table
Size
1860 x 1920 x 970mm
73" x 75" x 38"
2860 x 1920 x 970mm
113" x 75" x 38"
3360 x1920 x 970mm
132" x 75" x 38"
Packing Size
2650 x 1300 x 1650mm
104" x 51" x 65"
3600 x 1500 x 1750mm
141" x 59" x 69"
4300 x 1700 x 1880mm
169" x 67" x 74"
Net Weight
1600kg or 3527lb
2000kg or 4409lb
2680kg or 5908lb
Gross Weight
1700kg or 3748lb
2200kg or 4850lb
2764kg or 6094lb

Eastsign
ROTARY HEAT PRESS MOT-M USER MANUAL
6
3.2 Nameplate

Eastsign
ROTARY HEAT PRESS MOT-M USER MANUAL
7
4. Structure
4.1 Explanation of appearance and all parts
(1) left box
(11) supporting shaft
(tissue paper)
(27) left screw rod
(2) control panel
(12) blanket
(28) speed retarder
(pic paper)
(3) speed adjustor
(13)(14)(18)(19)(22)(27)
structural bar
(29) Speed retarder
(fabric)
(4) temperature control device
(15) left stand
(30) pic paper lading bar
(5) tension knob
(16) socket (17) electric
(31) tension adjusting bar
(pic paper)
(6) power indicator
socket for worktable
(32) tension adjusting bar
(fabric)
(7) heating button
(20) (21) (23) balance shaft
(33) fabric lading bar
(8) converter startup button
(24) Wheel box
(34) supporting shaft
(9) general power supply button
(25) speed adjustor
(35) (36) (37)
worktable connector
(10) tension adjusting bar
(tissue paper)
(26) screw rod
(38) right stand

Eastsign
ROTARY HEAT PRESS MOT-M USER MANUAL
8
(39) pic paper collector
(45) (46) air pressure switch
(for upper cylinder)/
(for lower cylinder)
(50) speed adjustor
(40) motor
(51) tissue paper
(41) right screw road
(52) motor
(42) belt driven shaft
(47) glasses
(53) air inlet port
(43) belt
(48) balance shaft
(54) fan
(44) right box
(49) tissue paper lading bar
(55) separate hand wheel

Eastsign
ROTARY HEAT PRESS MOT-M USER MANUAL
9
4.2 Configuration of left cabinet
4.3 Configuration of right cabinet

Eastsign
ROTARY HEAT PRESS MOT-M USER MANUAL
10
S1 separate shaft
L9 Air input mouse
L15 Oil tank
L1 Separate redactor
L10 Air pressure
adjustor Filter
L16 Overhaul manhole
L2‐Separate hand wheel
L17 Balance shaft
L3‐upper cylinder
L11 Main motor
L18 Cover
L4 Upper pressing shaft
L12 Balance shaft
L19 Power box
L5 Co‐adjusting shaft
L13 Chain
L20 Fan
L6 Main adjusting shaft
L14 Main Motor
4.4 Power box
L20 L21 L22 AC Contactor
L25Air Switch
L28 Transform Contactor
L23 Fan
L26 Fuse
L29 Time Relay
L24 Transformer
L27 Air Switch
L30 Heating Relay

Eastsign
ROTARY HEAT PRESS MOT-M USER MANUAL
11
4.5 Accessories list
Section
Name
Quantity
Series
Main Machine
(Mechanical)
Oil Drum
1
L15
Separate shaft
1
S1
Balance shaft
3
11, L17, L12
Supporting shaft
1
48
Adjusting shaft
2
L5, L6
Pressing shaft
1
L4,
Cylinder
1
L3,
Separate hand wheel
1
L2
Separate retarder
1
L1
Separate guide screw
1
Belt
1
43
Blanket
1
12
Main Machine (electric)
Loading bar
1
49
Colleting shaft
2
51
Tension knob
1
5
Control panel
1
2
Speed adjustor
1
3
Temperature control
device
1
4
Electrical button
3
7,8,9
Power indicator
1
6
Main Motor
1
L11
Air pressure adjustor
1
L10
Cover
1
L18
Motor
1
52
Speed adjustor
1
50
Fan
3
54, L20, L23
Air Pressure Switch
2
43, 44
AC contactor
3
L20,L21,L22

Eastsign
ROTARY HEAT PRESS MOT-M USER MANUAL
12
Relay
1
L29
Time Relay
1
L30
Contactor
1
L28
Air Switch
2
L25, L27
Fuse
1
L26
Transducer
1
L24
Worktable
Stand
2
15,38
Connector
3
35,36,37
Structural Bar
6
11,13,18,19,22,27
Belt Driver Shaft
1
42
Balance bar
3
20,21,23
Lading bar
2
30,33
Tension adjusting bar
2
31,32
Feed bar
1
34
Collecting bar
2
39
Speed retarder
2
28,29
Wheel box cover
1
24
Speed adjustor
1
25
Motor
1
40
Screw Road
2
26,41

Eastsign
ROTARY HEAT PRESS MOT-M USER MANUAL
13
5. Installation
Machine should be placed in empty space with flat ground, good ventilation and dry working environment.
5.1 Unpacking
(1) Remove the iron nail
(2) Loosen the screw on the packing
(3) Take away the top cover by hammer and crowbar
(4) Pull down the wooden side covers
(5) Take out the working table and axles
(6) Use forklift to move the machine to the right position
5.2 Installation of worktable
Notice: (3 or 4 operators needed)
Step 1. Standing by of the stands of the worktable (15) (18) Two operators respectively put left stand and right
stand on the front side of the machine.
Step 2. Install the belt driven shaft (42) Put the belt driven shaft (42) on the slot in the both left and right stand
after it walks across the belt, use two screw rods (26) (41) to fasten the shaft.
Step 3. Installation of worktable connectors (35) (36) (37) Screw the three connectors on the left stand and the
right stand; make sure the screw a little bit loose.
Step 4. Installation of three balance shafts (20) (21) (23) Screw three balance shafts on the left stand and the
right stand insufficiently, make sure the middle shaft laying under the belt; the rest two should pass through
the belt.
Step 5. Install six structural shafts (11)(13)(18)(19)(22)(27) Screw the six structural shafts on the left stand and
the right stand; make sure the screw a little bit loose.
Step 6. Install picture paper collector (39) Place well the two shafts of picture paper collector on the stands,
make sure to put the left side where gear located on the left stand.
Step 7. Installation of wheel box (24) Screw the motor on the left stand and pre-tighten it first, unlock the
chain and wrap it around the two shafts of picture paper collector with the motor, move and tighten the motor
to where it can gears better. Wire the speed controller correctly and cover the box.
Step 8. Installation of two adjusting bars (31) (32) and the speed retarder (28) (29) they connect to. Put the
two adjusting bars on the bearings; connect the left side with the speed retarders carefully, put the knob into
the retarders.
Step 9. Installation of two lading bars of fabric and picture paper (31) (32) Put the two adjusting bars on the
stands and lock it.

Eastsign
ROTARY HEAT PRESS MOT-M USER MANUAL
14
Step 10. Installation of Supporting shaft (34) Put the supporting shaft into the bearings on two stands，
Step 11. Installation of the worktable Fasten every screw which connect the shaft and stand, tighten the
bearing holder as well as each bearing rings.
5.3 Notice
1. Check whether all screws in machine are loose or not, tighten them if loose.
2. As the equipment is heating machinery, the machine should be used at environment of ventilating, dry
and noncorrosive gas. Make sure no inflammable and explosive materials around the machine.
3. The crust of machine must be grounded separately.
4. Choose power wire which has section above 6 square millimeters.
5. Keep the machine in level while installation. Use level meter to check if the machine is level.

Eastsign
ROTARY HEAT PRESS MOT-M USER MANUAL
15
6. Function
3. Transform Speed - -Control direction of rotation and speed of motor.
4. Temperature Control - -Setting temperature and controlling temperature range.
6. Power Direction - - Indicator of power
7. Heat - -Switch on/off circuit of heating.
8. Transform Start - -Switch on/off circuit of frequency converter.
9. Power - - Main Power Switch
16. Socket - -Electric Socket for Worktable
45. Air pressure switch - -Controller for upper cylinder
46. Air pressure switch - -Controller for lower cylinder
50. Speed adjustor - -It is for adjusting the speed of the Motor (52).
52. Motor- - It drives rotary of the roll collector on backside of the machine.
53. Air inlet port- -The port where input the compressed air
54. Fan- - Cool down the temperature of right cabinet
55. Separate hand wheel - -Control wrapping tension of blanket. (Press or loosen the
blanket)
Note: Please learn the details of frequency converter referring to the manual

Eastsign
ROTARY HEAT PRESS MOT-M USER MANUAL
16
7. Operation Guide
7.1. Before switching on the machine, make sure that all electrical wires are connected correctly. The body of
the machine must be connected to ground. Press the power switch and belt start rotary switch. Then,
adjust the rotary speed on speed adjustor (6) to optimum value. When the heating roller start revolving,
press “heating” button (5) and adjust the temperature to optimum value. (Default temperature is 220℃)
7.2. When the machine reaches the preset temperature, let the thermostat stabilize the temperature for a
while. Check the transfer result with small piece of printed transfer paper and substrate. Adjust the
temperature with reference to the testing result of the transfer.
7.3. Place the printed transfer paper and tissue paper (to prevent the contamination of blanket) in proper
position on working table and main machine. Feed the tissue paper first and collected by the shaft at the
rear. then feed textiles flatly. Lastly, feed the printed transfer paper to the machine evenly.
7.4. Before transfer begins, push the pressure controlling plastics roller on the main machine to the blanket.
Be aware that the pressure on both ends should be the same. If the pressure is not the same, release the
pressure controlling roller and push again.
7.5. When fabric and transfer paper comes out, attach the fabric to collecting rollers at the rear of the
machine or just drop on (19) Cloth pocket. Then, attach the transfer paper to collecting roller at the front
side of the machine under the table. So all materials can be collected automatically. The speed of
collecting transfer paper can be adjusted by the controller (8).
7.6. During the working process, the transfer speed can be adjusted (by “6”) according to the vividness of the
print.
7.7. When the transfer is finished, switch off the heating button to let the machine cool down. The operators
have to monitor the machine until the temperature drops to less than 100℃. Then, the operators may
switch off the machine. For special circumstances, the operators may switch off the main power supply
and heater simultaneously. The machine will cool down automatically and stop running after certain
intervals.
7.8. When there is sudden blackout and the machine is working at high temperature, turn the hand wheel
immediately and insert heat proof materials between the tank and blanket so that the hot roller does not
burn the blanket.

Eastsign
ROTARY HEAT PRESS MOT-M USER MANUAL
17
8. Notice for operation
8.1 Adjustment to blanket tracking
There is a little shrinkage of a new blanket working under high temperature. To avoid damaging new blanket by
improper operation, do not adjust the location of tracking adjusting roller(46) in the first two weeks (or first
100 hour of operating) for a new blanket; Release the blanket by hand wheel(32), then push (NOT PULL) the
blanket to the central of the oil drum manually.
The blanket may track to either side. This is a normal phenomenon. There is tracking adjusting roller (46) inside
the machine. When the blanket is tracking to right side, increase the tension of blanket band on the right hand
side a little bit, or decrease the tension of blanket band on the left hand side a little bit. When the blanket is
tracking to left side, increase the tension of blanket a little bit band on the left side, or decrease the tension of
blanket a little bit band on the right hand side.
This is the step of controlling the tension – insert the tailor-made spanner to the end of adjusting rod (47) and
(60). Increase the tension by revolving anti-clockwise. Decrease the tension by revolving clockwise. Be patient
as the adjustment cannot be completed in a short while.
8.2 Noise
The rollers and bearing may expand and create noise when they are heating to certain temperature. Do not
worry as it is a normal phenomenon.
8.3 Cleaning
Keep clean and tidy so that there is no dirt falling into electric circuit box and transducer. Do not open the
protective shield of transformer to avoid electric shock.
There is unique coating on heating roller. The roller cannot be scratched nor cleaned by acidic chemicals. The
warranty expires when the coating is peeled off.
8.4 Lubricating
The bearing should be lubricated with lithium base grease, a kind of high temperature resistant grease with
the flash point normally not less than 240 degree.
8.5 Blanket
Blanket is not a warranty part. Remind your colleagues to operate the machine with good practices.
When there is power failure or after finish the daily work, stop heating and use separate hand wheel to move
back the blanket from the oil drum thoroughly. Use soft paper board or papers (around 2 to 4mm thickness)
inserts to the gap between the blanket and the oil drum; this method can protect blanket from burning.

Eastsign
ROTARY HEAT PRESS MOT-M USER MANUAL
18
When the machine begins to works next time, take out the paper and tighten the blanket by operate hand
wheel.
PS: The instruction of changing blanket will be in a separated file.
8.6 Changing of oil
The oil drum was filled heat transfer oil (mineral base, suggested brand name: Total).
This is the specification:
Density: 0.83-0.87g/cm3 at 20 oC
Viscosity: 21-31 mm2/s at 50oC
Flash Point (open to air): 173 oC
Distillation range (2%v/v): 340 oC
Maximum temperature at use: 320 oC
Hole (80) is just for releasing oil only.
Hole (81) is just for filling oil only.