Easypix GoXtreme User manual

1
User Manual

2
Thank you for buying the GoXtreme WiFi action camera. Before
start using this product, please read this manual carefully to
maximize its performance and extend the life of the product.
Appearance and Buttons
1. Shutter button 7. LED light
2. LCD display 8. Micro HDMI port
3. Power / Mode button 9. Micro USB port
4. Lens 10. Micro SD card slot
5. Wi-Fi switch and status indicator (red) 11. Reset button
6. Microphone

3
LCD Display Illustration
Turn on the GoXtreme WiFi, the LCD will display the following
status and settings:
1. Camera mode
2. Video recording mode (default)
3. Wi-Fi icon (display when enabled)
4. TF card icon (display when loaded)
5. Resolution icon:
In camera mode, HI stands for 8 Mega Pixels (3264x2448),
and in video recording mode, it stands for FHD
(1920x1080,30fps);
In camera mode, LO stands for 5 Mega Pixels (2592x1944),
and in video recording mode, it stands for 720P
(1280x720,30fps);
HILO only displays in video recording mode, standing for 720P
(1280x720,60fps).
6. Mute mode, displays when enabled, and disabled by
default.
7. Counter, displays up to 999.

4
8. Timer, displays hours and minutes.
9. Battery icon: current battery level of the camera.
Note: the above icons may vary according to the status of the
GoXtreme WiFi.
Working Mode Flow Chart
After turn on the GoXtreme WiFi, you can press the
Power/Mode button to switch the following modes in turn:
In video mode, press the Shutter button to start recording, LED
flash, and press it again to stop;
In camera mode, press the Shutter button to take photo.
Use your GoXtreme WiFi
When you use the GoXtreme WiFi for the first time, please:
1. Insert a micro SD or micro SDHC card, as shown in the
following picture.
Camera mode (8MP)
Camera mode (5MP)
Video mode (720P ,60fps)
Video mode (720P,30fps)
Video preview mode (1080P default)

5
High speed card at least Class 4 is recommended; Turn off the DV
before inserting or removing the card.
2. Charging the battery. The DV uses built-in rechargeable
lithium battery. When the DV is off, connect it to the PC via
USB cable to charge the battery. During charging, the status
indicator (blue) will light on, and the indicator off when
charging completes.
Note: When the DV is on, connecting it to the PC will not
charge.
Turn on/off
1. Turn on: press and hold the button for about 3 seconds,
LCD displays “ON” and a beep can be heard from buzzer.

6
2. Turn off: press and hold the button for about 3 seconds,
LCD displays “OFF” and a beep can be heard from buzzer.
Note: The DV will turn off automatically if it is idle for 5
minutes.
Start to Use
Default setting: After turn on the GoXtreme WiFi, the default
setting is as below:
Video
recording
mode icon
The DV is in video recording mode.
HI
Video
resolution
FHD: 1080p@30fps
Recording time
Stands for 0 hour and 00 minute.
TF card icon
Display when a TF card is inserted, otherwise no display.
Battery level
Battery is full
Mute icon
The DV is in Mute mode, no Beep will be heard when
pressing the buttons. It displays only when Mute mode is
activated.

7
Wi-Fi icon
Display when activated.
The GoXtreme WiFi provides different shooting modes. Press
the button repeatedly, the following mode will display in turn:
Video
HI stands for FHD (1920x1080,30 fps) video
Lo stands for 720P (1280x720,30 fps) video
HILO stands for 720P (1280x720,60 fps) video
Photo
HI stands for 8M (3264 x 2448) resolution
Lo stands for 5M (2592 x 1944) resolution
Continuous
shot
The DV supports taking 3 photos continuously (only via
App)
Self-timer
In self-timer mode , you can set 0s, 2s or 10s (only via
App)
1. Video
To record a video, please check whether the DV is under Video
mode. If the icon is not displayed on the screen, press
the button repeatedly until it appears.
Start recording: Press and release the button, the icon and [:]
displayed in LCD will flash. At the same time the red indicator will
flash too, meaning the recording is in process.
Stop recording: Press and release the button, the icon and [:]
displayed in LCD will stop flashing. At the same time the red
indicator will stop flashing either, meaning the recording is stopped.
When the TF card is full, or the battery runs out, the recording will

8
stop automatically, and the recorded video will be saved before the
DV turns off.
After reaching a max. video recording time of 29 minutes the
camera will automatically stop. It can only be restarted manually.
2. Photo
To take a photo, please check whether the DV is under Camera
mode. If the icon is not displayed on the screen, press the
button repeatedly until it appears.
Press and release the button, a beep will be heard and the red
indicator will flash, meaning a photo is taken.(If you take photos
more than 999 copies, the LCD screen display only 999)
3. Enable/disable Wi-Fi
The Wi-Fi is disabled by default. Press the Wi-Fi button on the side
of the DV to enable it. When starting connecting to Wi-Fi network,
the indicator will flash, and when a Wi-Fi network is connected, the
indicator will remain on, and the Wi-Fi icon will display on LCD
screen. (In order to save power, Wi-Fi will be automatically disabled
if no terminal is connected after 30 seconds)
Wi-Fi is disabled by default When Wi-Fi is enabled, the
Wi-Fi icon will display on LCD

9
4. Enable/disable Mute mode
The buzzer is enabled by default. Under the Video or Photo mode,
press and hold the Shutter button to disable the buzzer and
indicator to enter Mute mode. Under Mute mode, the icon will
display on the screen; press and hold the Shutter button again to
exit Mute mode.
5. Connecting to HDTV
5.1 Connect the DV to HDTV via HDMI cable (optional)
If you need to transfer the image and audio to an HDTV for
playback, insert the Com end of the HDMI cable to the DV, and the
other end (output) to the HD input of the HDTV, as shown in the
following figure:
Buzzer is enabled by default When Mute mode is enabled,
the Mute icon will display on LCD

1
0
Note: Before connecting or removing the HDMI cable, please
stop video recording, playback and disconnect Wi-Fi first.
5.2 When HDTV is connected, it enters Playback mode, the LCD
displays as below:
In Playback mode, press the Power button to switch between
photos and videos. When there are several photos or videos, press
the Wi-Fi button to select the photo or video. When a video file
is selected, press the Shutter button to play it, and press the
Shutter button again to stop playing.
S/N
Icon name
Description
1
Playback mode
Under Playback mode currently.
2
File number
There are 31 files and you are viewing the 19th
one.
3
Video icon
The file is a video.
1
2
3

1
1
In Playback mode, press and hold the Shutter button , a prompt
of deleting the file or formatting will appear. Press the Wi-Fi
button to switch between deleting or formatting, then press the
Power button to select Yes or No, and press the Shutter
button to confirm and exit.
6. Connecting to PC
6.1 Turn on the DV and connect it to the USB port of the PC via the
attached USB cable. The DV will enter U-disk mode and the LCD
will display as below after connection:
Now you can view the photos or videos taken by DV on PC.
Note: After the DV connecting to PC to enter U-disk mode, you
will see two removable disks displayed in My computer of
Windows, one is the TF card, storing all the photos taken and
video recorded by users; the other one stores the system file
information, including a file named SSID_PW.CFG, containing
the AP ID of the DV and the password for AP login. Users can
view this information but cannot modify, delete or format
them.

1
2
6.2 In U-disk mode (PCU mode), press the Shutter button to
switch to web cam mode (PCC mode), and the LCD will display as
below:
Now you can start the web cam through application. To return to
U-disk mode (PCU mode), press the button again.
Note: Driver is not required for web cam mode (PCC mode) on
Windows XP (SP3) version or above.
APP (support Android and iOS)
1. How to install an APP
1.1 Search for ”SYMAGIX” in Google Play (for Android OS),or scan
the QR code printed on the gift box to find the APP and
install it according to the instruction.
1.2 Search for ”SYMAGIX” in APP Store (for iOS) or scan the QR
code printed on the gift box to find the APP and install it
according to the instruction.

1
3
2. Android APP
2.1 Install SYMAGIX APP (provided by dealer or via internet) on
Android phone or tablet. When installation completes, the LCD will
display icon .
2.2 Insert the TF card and turn on the DV, then press the Wi-Fi
button to enable it. Now you can see the Wi-Fi icon on the LCD.
2.3 Enable Wi-Fi on Android phone or tablet and search for
wireless AP signal “GoXtreme WiFi”, then connect it to DV, until the
system displays “Connected successfully”.
2.4 Click the icon in the App list of the Android phone or tablet
to open it. Now you can preview the image sent by the DV on the
phone or tablet and start some operating. The operation interface
on terminal is shown in the following figure.
1. Video resolution
2. White balance
3. Setup (enter setup
menu)
4. Enter Playback mode
5. Shutter button
6. Photo mode
7. Video mode
8. Wi-Fi signal icon
9. DV battery icon

1
4
3. iOS APP
3.1 Install SYMAGIX APP (provided by dealer or via internet) on
iOS phone or tablet. When installation completes, the LCD will
display icon .
3.2 Insert the TF card and turn on the DV, then press the Wi-Fi
button to enable it. Now you can see the Wi-Fi icon on the LCD.
3.3 Enable Wi-Fi on iOS phone or tablet and search for wireless AP
signal “GoXtreme WiFi”, then connect it to DV, until the system
displays “Connected successfully”.
Note: While connecting to DV for the first time, you need to enter
password “1234567890”. And will not require typing the code again
once connected previously.
3.4 Click the icon in the App list of the iOS phone or tablet to
open it. Now you can preview the image sent by the DV on the
phone or tablet and start operating. The operation interface on
terminal is shown in the following figure.
1. DV battery icon
2. Video resolution
3. White balance
4. Setup (enter setup menu)
5. Enter Playback mode
6. Shutter button
7. Photo mode
8. Video mode

1
5
Note:
1. A TF card must be inserted if you need to take a photo,
record a video or download files on the terminal.
2. The Wi-Fi indicator will remain on when the terminal is
connected to DV.
DECLARATION OF CONFORMITY
easypix herebly declares that the product GoXtreme WiFi is in conformity to all the essential
requirements of Directive 1999/5/EC. The declaration of conformity can be downloaded here:
http://www.easypix.info/download/pdf/doc_goxtreme_wifi.pdf
For technical help please visit our support area on www.easypix.eu.
Only EU