Eberhart Hector User manual

Hector —
Assembly Guide
Assembly Guide Video
On our website you will find guidelines to help you make sure that your furniture is
assembled correctly. Access our assembly guides with ease using the camera on
your smartphone to scan the QR code on the left.

A B
C
D
Step 1 —
With your Hector table top (A)
turned upside-down on a soft
surface, begin by mounting one
Hector table leg (B), and make sure
that there is a protective washer
(C) placed in between the table leg
and table top bracket.
Do not tighten leg completely.
Hector —
Assembly Guide
Before we get started:
• We recommend that you leave the table in its original packaging at room temperature for 24 hours after
receiving the table. This is to acclimate.
• Make sure that all parts are included in the packaging.
• Protect the table from scratches by assembling it on the cardboard box itself or use a large blanket/carpet.
• We do not recommend assembling the table alone, you should be a minimum of two people.
A. Hector table top ( 1 )
B. Hector table legs ( 5 )
C. Protective washers ( 5 )
D. Hector assembly ring ( 1 )

Step 2 —
Place your Hector assembly ring
(D) on the table leg, lowering to a
center position.
• Make sure the assembly ring
is leveled even horizontally.
• The small hole on the
assembly ring should be
facing the floor when the table
is in place.
Step 3 —
Through the holes in the assembly
ring, gently mount the remaining
4 Hector table legs (B) and do not
tighten completly, until all 5 legs
are mounted.
• When all table legs are
mounted, make sure the
assembly ring is horizontally
level placed at center position.
• Tighten the table legs
completly.
Step 4 —
Gently lift your Hector dining
table and flip it over to its natural
position.
Congratulations, your new Hector
dining table is now ready for use.

Extended Maintenance Information
On our website you will find extended information on maintenance of our products,
along with tips and tricks to help you take good care of your furniture. Use the camera
on your smartphone to scan the QR code on the left to visit our maintenance page.
Maintenance & Care —
Information
Maintenance and care on a regular basis can prolong the life of your furniture, and
make sure it will last through ages. Here, we have gathered a short introduction to
inform you about the most important things to know. We highly recommend you visit
the maintenance section on our website for extended maintenance information.
Concrete —
• Concrete tabletops are pre-treated with a liquid and silicone-free wax from production. If you want a raw and
more variegated tabletop, we recommend using the table without further treatment. If you want a more well-
protected top against everyday dirt, we recommend that you regularly treat the table with the same liquid wax
that we have given the table from its birth.
• Avoid direct sunlight on the furniture the rst 4 weeks.
• Wipe with a clean, damp cloth. We recommend cleaning without detergent.
Wood —
• All wooden parts are made of solid oak. Wood is a natural material, which can be affected by changing
humidity, heat, direct sunlight and normal wear and tear.
• For daily care use a damp cloth without detergents or washing liquid or use cleaning products specically
designed for solid wood.
• We recommend oil treatment of the furniture 4-6 times in the rst year, and afterwards minimum twice a year,
preferably before and after the winter period.
Linoleum —
• To prevent stubborn stains, trivets should be used under ower pots, vases and preferably also under cups
and glasses etc. It is important to remove stains immediately to prevent permanent marks.
• For ongoing maintenance of the surface use a linoleum care product. In case of heavy soiling use a suitable
neutral detergent (eg Forbo Cleaner).
• Small scratches can be made less visible with massaging your nger or a fat nut (eg walnut) against the
scratch.