Eclipse TD D2 User manual

SpeakerStand(D2)InstructionManual
■ForSafeUsage
Ignoringwarningsandsubsequentincorrectuseoftheproductcouldresultindeath
orseriousinjuly.
Ignoringwarningsandcautionswithsubsequentincorrectuseoftheproductcould
resultinpersonalinjulyoryourpossessions.
●Donotsetthisspeakerstandinahighplace.Ifthestandfalls,itcancauseaninjuly.
●This stand is specifically designed to match the 512 speaker. Please do not use the stand for other functions.
Installationofthestandinsuchawaythatitisunstablecancauseittocollapseandmayresultininjuly.
●Placethestandonalevelfloor.Anunevenfloormaycausethestandtofalloverandcouldresultininjuly.
●Donotsetupthestandinhallwayorinanareaoffrequentmovement.Accidentalbumpingintothestandmay
resultininjuly.
●Installthestandonasolidsurface.Settingupthestandonanunstablesurfacecancauseittofallandmayresultin
injuly.
●Whenmovingthisstandtochangeitslocation,becarefulnottotouchthelegpins.Contactwiththelegpinsmay
resultinaninjuly.
●Thisproductisdesignedwithlegpinsontheundersideofthebase.Whenassemblingor moving the stand, be
carefulnottoallowthelegpinstofallontothefloororbedraggedacrossthefloor.Ifthestandfallsorisdragged
acrossthefloor,itcouldresultinpersonalinjulyordamagetoyourfloor.
●When tightening or loosening the hex head Allen bolts during assembly, be careful not to scrape your hands
againstthelegpinswhenturningthewrench.Injulycanresult.
●Donotattempttomovethestandwiththespeakerplacedontopofit.Thespeakercouldfallandcauseinjuly.
●Donotclimbontothestandorhangfromit.Pleasebeespeciallywatchfulofchildreninthisregard.Ifthestandfalls
orbreaksitcouldresultininjuly.
●Thestandinheavy,sohaveatleasttwopeoplehelpwhenunpackingormovingit.Abackstraincouldresult,orthe
standcouldfallonyourfeet,causinginjuly.
〔１〕CautionsforUse
(1) Thisstandismeantforusewiththespecifiedspeakersystems.Pleasedonotusestandforotherfunctions.
(2) Thestandisheavyandhaslegpinsinstalled,Usecautionwhenhandlingit.
(3) Besuretosetthestanduponasolidandlevelfloor.Donotpleasethestandinanunstablelocation.
(4) Becarefulnottopushthestandover.
(5) Becarefulnottoknockthespeakersystemoffthestand.
(6) Tocleanthestand,gentlywipethesurfacewithasoftclothmoistenedwithamildcleaningsolutions.
Donotusechemicalssuchasthinnerorsolvent.
ThankyouforpurchasingtheECLIPSETDspeakerstand.Beforeassemblingyournewspeakerstand,pleasetakea
momenttoreadthroughthismanualandfollowitsinstructions.Assemblyotherthanspecifiedintheseinstructions,or
useofpartsotherthanthosedesignated,canresultinanaccidentorinjury.Afterassembly,pleasekeepthismanualin
aconvenientlocationforyourreference.
Thefollowingcautionsareprovidedtohelpyouusethisproductsafelyandproperly,avoidinginjuryorlosstoyouor
other people in your home. Please familiarize yourself with these cautions before proceeding to the assembly
instructions.
Warning
Caution
Warning
Caution

After the top plate is attached to the support
columns, turn the assembly upside down.
Use the same procedure explained in (1)-①
above, then use the large Allen wrench to
lightly fasten the base plate to the support
columns with the screws. Do not
completely tighten the bolts at this time.
①
②
Base Plate×１
Flush Head Allen Screw×２
Support Column×１
Top Plate×１
Flush Head Allen Screws×２
Leg Pin Plate×２
Leg Pin×５
Leg Pin Locking Nuts×５
・Small Allen Wrench×１
・Large Allen Wrench×１
・Flush Head Allen Screw×4
・Leg Pin Locking Nuts×5
・Leg Pin×5
・Leg Pin Plate×5
(1)AttachtheBasePlate
(4)AttachtheJoint
●DimensionsandWeight
※Specifications and external appearance may change without
notice.
TopPlate
（L×Wmm)
Height(mm)
BasePlate
（L×Wmm)
278×237 720
Weight
(kg)
28350×325
〔２〕PartNamesandQuantities
〔３〕AssemblyInstructions
〔４〕Specifications
After completing final assembly of
the top plate and base plate, leave
the stand resting on its side and
attach the leg pins to the base plate
extending above the base plate
surface by about 5 threads.
If the leg pins are properly
threaded but are still hard to turn,
use the small hard to turn, use the
small Allen wrench to turn them.
①
Attention：
(5)AdjusttheLegPinHeight
After the leg pins have been
attached, set the stand upright and
place it in the location desired for
use.
When setting up or moving the
stand, be careful that the leg pins
do not scratch your floor.
Using the small Allen wrench, turn
the leg pin down so that it becomes
flush.
After adjusting the last leg pin, set
the locking nut in place.
If the locking nut is hard to turn,
use the open end wrench provided.
①
Attention：
②
③
Attention：
Be sure the Allen wrench is pushed all the way into the
screw's socket before tightening.
Attention：
(6)PlacetheSpeakerontheStand
Align the base of the speaker with
the top plate of the stand and set it
in place.
①
(2)AttachtheSpeakerBody
(3)TopPlateandBasePlateFinalAssembly
Place the top plate on the standing support
columns. Use the large Allen wrench to
attach the 4 flush head Allen screws, lightly
fastening the top plate to the columns. Do
not completely tighten the screws at this
time.
①
After the base plate is
temporarily fastened, rest the
stand on its side on the floor
with the front side down.
Use the large Allen wrench to
tighten the screws in the top
plate and base plate.
①
②
FUJITSUTENLIMITED
KOBE,JAPAN