Eco-Smart AB Series User manual
BK Series AB Series VB SeriesXL Series
INSTALLATION,
OPERATION
AND MAINTENANCE
MANUAL
! WARNINGS:
IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED EXACTLY, A FIRE OR EXPLOSION
MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.
PLEASE READ THESE INSTRUCTIONS COMPLETELY
BEFORE OPERATING THE ECOSMART™ FIRE.
e-NRG bioethanol is the
ONLY fuel to be used in
this appliance.
ENGLISH INSTALLATION, OPERATION
AND MAINTENANCE MANUAL
Please read these instructions completely before
operating the EcoSmart™ Fire.
1 – 22
DEUTSCH INSTALLATIONS-, BEDIENUNGS-
UND WARTUNGSHANDBUCH
Bitte lesen Sie diese Anweisungen vor der
Inbetriebnahme des EcoSmart™ Fire vollständig durch.
23 – 44
FRANÇAIS MANUEL D’INSTALLATION,
D’UTILISATION ET D’ENTRETIEN
Veuillez lire ces instructions dans leur intégralité avant de
faire fonctionner le système EcoSmart™ Fire.
45 – 66
中文 安装，操作
和维修指南 67 – 88
日本語 取扱説明書
（取り付け•操作•お手入れ） 89 – 110
ESPAÑOL MANUAL DE INSTALACIÓN, USO Y MANTENIMIENTO
Por favor, lea las instrucciones completamente
antes de utilizar el EcoSmart™ Fire.
111 – 132
www.ecosmartre.com e-NRG Bioethanol is the only fuel to use in this appliance.
ENGLISH
UNVENTED ALCOHOL-FUEL-BURNING DECORATIVE APPLIANCE
35PZ
MH46715
All EcoSmart Fire Burners are UL Listed. (Except VB2)
Bioethanol replaces are classied by regulations and standards as
decorative replace appliances intended for occasional use only (not
for heating).
EDUCATE ALL USERS
This type of technology is not well known and therefore we
recommend that owners diligently induct any potential user of their
Fire to ensure everyone is aware of the safety procedures associated
when using e-NRG Bioethanol as a fuel source.
Operational Videos and Manuals can be found on our website or by
contacting your local distributor.
WHY REGISTER YOUR WARRANTY?
Registering your warranty achieves more than simply activating your
warranty - it provides our head oce with the information that we
require in order to communicate important safety and regulatory
information to you should the need arise.
This could include things like:
• Prompt notication in the unlikely event of a potential hazard,
• Changes to fuel storage regulations, supply channels or special
oers,
• Reminders about regular safety steps and maintenance procedures,
• New model announcements or accessories that suit or enhance
your purchase.
It is important that we are able to communicate eectively with our
customers as part of our commitment to continual improvement,
consumer safety and property protection.
If you purchased your product through an external distributor, retailer
or agent The Fire Company does not have these details on le and
may have trouble sourcing them as systems and best practices vary
from business to business.
Please register your warranty today. You can do this online at the
following web address: or by
sending through your details via email using the details below.
Showrooms 3 & 4, 40-42 O’Riordan Street
Alexandria NSW 2015 Australia
Tel: +61 2 9997 3050
Email: info@ecosmartre.com
FLAMMABLE
Refer to the e-NRG Safety Data Sheet (SDS) for important Health and
Safety information.
These include:
• Permitting for volumes of e-NRG (e.g. for USA, greater than 5 gallons
stored inside, or greater than 10 gallons stored outside).
• Removal of all potential sources of ignition including sparks and
open ames.
• Maintenance of good ventilation of enclosures where e-NRG is stored.
• Storage of e-NRG (e.g. for USA, greater than 10 gallons in an
approved storage cabinet).
• Storage in such a way as to reduce the likelihood of spillage or
container rupture.
• Responsible handling to include:
- Use of the Jerry Can in an approved manner and with attention to
the possible presence of ames or other ignition sources in or near
the
appliance,
- Limiting access to qualied users,
- Proper transfer techniques to limit spillage and generation of
static electric discharge (i.e bonding and grounding),
- Proper labeling and signage in accordance with applicable re codes.
These precautions are necessary to reduce risk of damage to property,
injury and death resulting from accidental ignition of e-NRG.
Australia
Visit -
Call - 1300 003 NRG
USA
Visit - www.e-NRG.com
Call - (888) 670 ENRG
Or contact your local EcoSmart Fire distributor.
© Copyright 2004 - 2018 The Fire Company Pty Ltd. All rights reserved. V0318
Regulatory Information for the Safe Handling
and Storage of e-NRG Bioethanol
Decanting your e-NRG Bioethanol
into the Jerry Can
Decanting your e-NRG Bioethanol from the
Jerry Can into the Burner
Lighting the Burner
Regulating the Flame
Baes
Turning your Burner OFF
- Extinguishing the ame
Re-igniting the Burner
3 – 4
5 – 7
8
9 – 11
12 – 13
14 – 17
14
14
15
16
16
16
17
17
18
19
20
21
22
www.ecosmartre.com e-NRG Bioethanol is the only fuel to use in this appliance.
ENGLISH
! WARNING
2. LOCATING THE FIRE
3. VENTILATION
i.
4. FUELING THE FIRE
DO NOT FILL WHILE
OPERATING
DO NOT FILL
WHILE HOT
5. OPERATING THE FIRE
© Copyright 2004 - 2018 The Fire Company Pty Ltd. All rights reserved. V0318
7. USING ACCESSORIES
authorised
.
supplied
.
www.ecosmartre.com e-NRG Bioethanol is the only fuel to use in this appliance.
ENGLISH
Please ensure that all items have been received. The Burner Range
includes the minimum equipment required to operate the Burner safely.
The Burner is the core product of the EcoSmart Fire as it is the
chamber that houses the fuel.
BK5
123mm x 400mm x d317mm
[4.4in] x [15.7in] x d[12.5in]
7.6kg [16.6lbs]
BK3
123mm x 400mm x d317mm
[4.4in] x [15.7in] x d[12.5in]
7.1kg [15.7lbs]
BK2UL
123mm x 400mm x d317mm
[4.4in] x [15.7in] x d[12.5in]
6.7kg [14.7lbs]
XL SERIES
XL1200
h112mm x l1200mm x d195mm
h[4.4in] x l[47.2in] x d[7.7in]
15.7kg [34.5lbs]
XL900
h112mm x l908mm x d195mm
h[4.4in] x l[35.7in] x d[7.7in]
11.9kg [26.3lbs]
XL700
h112mm x l700mm x d195mm
h[4.4in] x l[27.6in] x d[7.7in]
9.2kg [20.2lbs]
XL500
112mm x 500mm x d195mm
[4.4in] x [19.7in] x d[7.7in]
6.5kg [14.3lbs]
XS340
87.2mm x 340mm x d190mm
[3.4in] x [13.4in] x d[7.5in]
3.7kg [8lbs]
AB SERIES
AB8
156mm x ø360mm
[6.1in] x ø[14.2in]
5.9kg [13lbs]
AB3
94mm x ø260mm
[3.7in] x ø[10.2in]
2.4kg [5.4lbs]
Burner Standard Equipment Received
Series Model Manual Jerry Can Lighting Rod Lighter Extension Spout Top Tray Baes
BK Series BK5, BK3, BK2UL 1 1 1 1 - 1 -
XL Series
XL1200, XL900,
XL700, XL500, 1 1 1 1 - - 2 - 5
XS340 1 1 1 1 - - -
AB Series AB8, AB3 1 1 1 1 1 (AB3 only) - 1 (AB8 only)
VB Series VB2 1 1 1 1 - - -
VB SERIES
VB2
122mm x 330mm x d110mm
[4.8in] x [13.0in] x d[4.3in]
1.8kg [4lbs]
© Copyright 2004 - 2018 The Fire Company Pty Ltd. All rights reserved. V0318
BKSeries AB Series VBSeriesXLSeries
INSTALLATION,
OPERATION
AND MAINTENANCE
MANUAL
! WARNINGS:
If the InformatIonIn thIs manual Is not followed exactly,a fIre or explosIon
mayresult causIng property damage, personal Injury or loss of lIfe.
PLEASE READ THESE INSTRUCTIONS COMPLETELY
BEFORE OPERATING THE ECOSMART™ FIRE.
e-NRGbioethanol is the
ONLYfuel to be used in
thisappliance.
In order to obtain optimal and safe results from your
appliance
, we recommend carefully reading the
entire instruction manual.
297mm x 210mm x d 8mm
[11.7in] x [8.3in] x d [0.3in]
This 5 Litres [1.25Gal] Jerry Can has been chosen for its unique safety features. It includes an automatic
stop ow, a fast ow rate, a locking thumb button control, and a self-venting system. The Jerry Can will
allow safe storing/decanting of the e-NRG Bioethanol used in the Burner.
Due to safety regulations the Jerry Can provided with this package comes without fuel.
320mm x 310mm x d 195mm
[12.6in] x [12.2in] x d [7.7in]
Adaptors are used to connect the No Spill Spout to the e-NRG bottle. Depending on the thread of the
bottles used in each country the adapter may look dierent (if available in your country).
This long slender piece of stainless steel with a small hook return at the end enables you to safely
adjust the slider position on the Burner at any time. It is also used for the ignition procedure.
657mm x 28mm x d 23mm
[25.9in] x [1.1in] x d [0.9in]
This rellable butane lighter supports the safe ignition of the lighting rod. The length of the lighter further
enhances the management of the lighting process.
* Due to safety regulations the butane lighter provided with this package comes without fuel. Small re-charge cans of butane gas with the necessary
connections can be purchased from your hardware store. Lighter image is indicative only, the model included may vary from time to time.
185mm x 15mm x d 15mm
[7.3in] x [0.6in] x d [0.6in]
An extension spout is included with the AB3 Burner. This is for use with models that have more
restricted access to the lling point so that lling can be done in a safe manner according to the
procedures outlined in the Operations Manual.
500mm x ø 25mm
[19.7in] x ø [1in]
These eciency devices are a standard inclusion with the XL Series and AB8 Burners. Baes (or
Rings) are placed over the internal burner vents when cold and not operating and serve to increase the
eciency of the burner as well as further stabilise the ame of the burner.
XL Series Eciency Ring
10mm x 80mm x d 10mm 5mm x ø 158mm
[0.4in] x [3.1in] x d [0.4in] [0.2in] x ø[6.2in]
www.ecosmartre.com e-NRG Bioethanol is the only fuel to use in this appliance.
ENGLISH
For those models that come with a Wind Screen Static – the Wind Screen
can be xed to the front of the model via the four (4) xing points on the
appliance facade using the circular screws provided.
WARNING: DO NOT OPERATE WITHOUT THE GLASS WINDSCREEN
© Copyright 2004 - 2018 The Fire Company Pty Ltd. All rights reserved. V0318
BK SERIES XL SERIES
S
These markings on the top of the burner illustrate the various settings
the burner can be operated at using the sliding mechanism.
Feature not available for models in the XL Series.
BK3 SLIDER
BK5
The following safety markings are included on the Burner. It is
important that you take the time to understand what they mean as
failure to follow instructions related to these markings could result in
property damage, bodily injury or even death.
These pictograms are used to bring to your attention the following
important safety messages:
DO NOT FILL WHILE
OPERATING
DO NOT FILL
WHILE HOT
This warning message is also on all burners to bring to your attention
important safety messages:
Inside the burner you will see the following fuel level markings.
WARNING! Never ll above the MAX volume mark.
The Caution and Warning labels that are applied to the lighting rod are
included to reinforce important safety messages. This is what they say:
Every EcoSmart Fire Burner includes a data plate which provides
minimum clearances and safety information. It also includes a unique
bar code, serial number and key manufacturing information.
DATA PLATE
Date of manufacture
Data Plate: EcoSmart™ Fire “BK5”
UNVENTED ALCOHOL-FUEL-BURNING DECORATIVEAPPLIANCE
Designed in Australia by The Fire Company Pty Ltd
Use e-NRG Bioethanol FUEL ONLy.
Do not use an appliance insert or other products not specified for
use with this product. WARNING: THIS APPLIANCE HAS NOT BEEN
TESTED WITH AN UNVENTED GAS LOG SET.TO REDUCE RISK OF
FIRE OR INJURY,DO NOT INSTALL AN UNVENTED GAS LOG SET
INTO THE APPLIANCE. THIS APPLIANCE HAS NOT BEEN TESTED
FOR USE WITH GLASS DOORS. TO REDUCE THE RISK OF FIRE OR
INJURY,DO NOT INSTALL GLASS DOORS. TO AVOID THE RISK OF
DAMAGING APPLIANCE MATERIALSAND INCREASING THE RISK
OF SPREADING A FIRE, DO NOT USE THE APPLIANCE TO COOK
OR WARM FOOD.
Thermal Output Net 14 MJ/hr – 13000 BTU/hr – 3.5 kW
Averagefuel consumption 0.64 L/hr [0.17 Gal/hr]
Minimum Room Size: 70m3[2472ft3]
Compulsory clearances to nearest combustible:
Indoor - Overhead: 1500mm [59.05in] - Side/Rear: 600mm [23.6in]
Outdoor - Overhead: 2000mm [78.7in] - Side/Rear: 600mm [23.6in]
For installation and use only in a manufacturer approved enclosure.
Must be inserted into non-combustible material ONLY.
Before installing or operating refer to instruction manual.
Retain Owner’sManual (Instructions) for future reference.
www.ecosmartfire.com
MH46715
35PZ
V0617
A warning sheet has been included with the burner to alert you to
reading the operations manual in full.
www.ecosmartre.com e-NRG Bioethanol is the only fuel to use in this appliance.
ENGLISH
Ensure that the mouth of the ame is positioned a minimum of 1500mm [59.1in] away from curtains,
ammable materials, and other sources of ignition. Be aware of drafts. The oor must be level and the Burner
positioned on a at surface. The Burner must only be placed into non-combustible materials and must be
installed in accordance with the outlined safety requirements and clearances. Please send drawings to your
local representative to conrm the setting complies with the manufacturer’s requirements prior to installation.
EcoSmart Fire Burners can be installed into two (2) types of settings:
A.Those that are encased by non-combustible materials similar to that
which you would nd in a traditional masonry set-up. We refer to this
installation type as “WITHIN A FIREBOX”
B .Those that are not encased by non-combustible materials and set
up in a more modern setting without sides or a top. We refer to this
installation type as “WITHOUT A FIREBOX”
A. FIREBOX MEASUREMENTS FOR “WITHIN A FIREBOX” INSTALLATION (Fig.1)
BURNERS
Minimum Firebox
Width
(X)
Minimum Firebox
Depth
(Z)
Minimum Firebox
Height
(Y)
BK SERIES 650mm [25.6in] 365mm [14.4in] 650mm [25.6in]
XL1200 1500mm [59.1in] 350mm [13.8in] 500mm [19.7in]
XL900 1200mm [47.2in] 350mm [13.8in] 500mm [19.7in]
XL700 1000mm [39.4in] 350mm [13.8in] 500mm [19.7in]
XL500 800mm [31.5in] 350mm [13.8in] 500mm [19.7in]
XS340 450mm [17.7in] 300mm [11.8in] 450mm [17.7in]
AB8 650mm [25.6in] 450mm [17.7in] 800mm [31.5in]
AB3 400mm [15.7in] 350mm [13.8in] 500mm [19.7in]
AA. BURNER PLACEMENT “WITHIN A FIREBOX” (Fig.2)
BURNERS Minimum Distance
to Front (A)
Minimum Distance
to Rear (B)
Minimum Distance
to Left (C)
Minimum Distance
to Right (D)
BK SERIES 45mm [1.8in] 30mm [1.2in] 150mm [5.9in] 150mm [5.9in]
XL SERIES 50mm [2.0in] 40mm [1.6in] 150mm [5.9in] 150mm [5.9in]
XS340 45mm [1.8in] 65mm [2.6in] 150mm [5.9in] 150mm [5.9in]
AB SERIES 45mm [1.8in] 30mm [1.2in] 150mm [5.9in] 150mm [5.9in]
Custom made reboxes must:
- Be made out of a non-combustible material such as stainless steel
- Be constructed to accommodate a Top Tray
- have built-in spacers of 20mm (0.8 in.) on all sides to ensure that it does not sit directly
against any combustible material and an air gap is incorporated for insulation around the
box construction. (Fig. 3)
.
VB BURNER
The VB2 burner is specially designed as a ‘drop-in’ burner system to a purpose-built, existing
or new, replace setting. You should seek conrmation from the insert manufacturer and install
the replace according to the manufacturers instructions before inserting the burner.
Fig.1
Fig.2
Fig. 3
© Copyright 2004 - 2018 The Fire Company Pty Ltd. All rights reserved. V0318
B. BURNER PLACEMENT “WITHOUT A FIREBOX” (Fig.4)
BURNERS
Minimum Indoor
Overhead
Clearance (E)
Minimum Outdoor
Overhead
Clearance (F)
Minimum Distance to
Combustible Materials
(G)
BK SERIES 1500mm [59.1in] 2000mm [78.7in] 600mm [23.6in]
XL SERIES 1500mm [59.1in] 2000mm [78.7in] 600mm [23.6in]
AB SERIES 1500mm [59.1in] 2000mm [78.7in] 600mm [23.6in]
Fig. 4
Please note that:
- Any furniture items or ttings directly above or beside the Burner
installation must be deemed suitable for heat tolerances by
their manufacturer e.g. electronic items including screens and
entertainment equipment, wallpaper, laminates, veneers, glues and
reconstituted materials.
- A heat reective panel made of non-combustible material (ideally
stainless steel) must be installed as the surround and top of the
replace setting to assist in heat distribution. The Fire Company Pty
Ltd is not liable for any injuries or damages sustained through the
use of panels not manufactured by The Fire Company Pty Ltd.
- Glass or mirrored surfaces near the Burner installation must be
toughened.
- If inserting a Burner into an existing masonry replace, adjust the
damper within the existing replace in order to keep the heat from
escaping through the ue.
EcoSmart Fire.
WARNING! FIRE HAZARD. DO NOT PACK REQUIRED AIR SPACES,
(THE AREA BETWEEN THE FIREBOX AND THE SPACER) WITH
INSULATION OR OTHER MATERIALS. THE AIR SPACES ARE NEEDED
TO MAINTAIN PROPER TEMPERATURE AROUND THE FIREBOX.
FIRE SCREENS
If installing a re screen into your setting there must be a 40mm [1.6in]
gap between the burner platform and the under side of the glass
edge to enable air circulation around the burner. This assists with fuel
eciency, burner temperature and ame quality.
There are many dierent variations available for installing the Burner.
In all cases, the Burner must be:
- Installed into non-combustible material ONLY, such as stainless
steel, concrete, brick and stone
- Installed after all gas connections or pipelines in the area are
disconnected and made safe by an appropriately qualied and
licensed professional
- Installed and operated in a xed and secure position before lling,
lighting and operating. Burners are not meant to be moved because
movement creates the risk of accidental fuel spillages. If you move
the Burner, make sure no fuel was spilled before you ignite the
Burner.
- Models from each range (Grate/Fireplace Inserts/Designer/Outdoor)
have varied installation requirements. Refer to the specic section of
the manual for the detailed requirements of the model purchased.
- Mounted into a level surface made of non-combustible materials.
The best location for your EcoSmart Fire is:
- In a large, open space at least 1500mm [59.1in] away from any
combustible materials, such as curtains, wallpaper, veneer, etc.
- On a level oor – the oor can be made of any material.
- In a rebox made of non-combustible materials, such as steel,
concrete, brick, or stone.
- Positioned so that any accumulation of weather debris/pooling of
water is eliminated.
- NOT INSTALLED DIRECTLY BESIDE OR NEAR WALLPAPER,
LAMINATE, VENEER OR ANY SURFACE THAT HAS NOT BEEN
FIRE RATED (THE HEAT WILL IMPACT THE MATERIAL). REFER TO
PRODUCT SPECIFICATION OF WALLPAPER, LAMINATE, VENEER
OR GLUE FOR HEAT TOLERANCES.
- Installed into a setting that has a straight back – the incorporation of
angled backs alters the aerodynamics of the ame environment and
could lead to an unstable ame behaviour.
-Fitted within a Top Tray that is not more than 200% the size of the
total Burner size. (Not applicable in USA/Canada)
www.ecosmartre.com e-NRG Bioethanol is the only fuel to use in this appliance.
ENGLISH
The incorporation of a Top Tray into your setting protects against heat
transference and aids in the collection of accidental spillage. Some
models come with Top Trays, others do not. Top Trays are available as
an accessory through The Fire Company or your local distributor.
When installing multiple Burners a maximum of three [3] Burners may
be installed into the one Top Tray (excluding the XL Series which can
only have one [1] Burner per Top Tray). Special considerations should
be made to multiple Burner installations in order to avoid potential
accidents. Contact your local distributor about design and analysis
advice to minimise adverse impacts.
Top Trays provided by The Fire Company are tted directly into the
Burner shelf from above. The Burner is then inserted into the Top Tray
setting and adjusted (using the levelling screws) to sit ush.
The size of the cut-out should not give more than 5mm [0.196in]
clearance. Top Trays must not be more than 200% of the total size
of the corresponding Burner.
Physical model dimensions should be veried against cut out
dimensions BEFORE installation begins to conrm tolerances align.
NOTE: Top Trays are not required in USA and Canada.
W
The base and the sides of the burner must never come into direct contact with combustible
materials.
Side clearances to xed and stable furniture items that are not susceptible to movement such as
lounges or patio furniture must remain a minimum of 600mm [23.6in] away from the ame at all
times.
Overhead clearances to items that are susceptible to movement
(e.g. Curtains/Trees) must remain a minimum of:
- Indoors: 1500mm [59.1in] away from the ame at all times.
- Outdoors: 2000mm [78.7in] away from the ame at all times.
Note: Stainless steel will rust or corrode over time if contamination or debris is not cleaned
or removed immediately. When not in use, it is recommended that you protect your replace
from water damage or corrosion with a protective cover and always use the Burner Lid
included with your model to safeguard the burner.
Indoor Clearances
[23.6]
600mm
[59.1]
1500mm
Outdoor Clearances
[78.7]
2000mm
[23.6]
600mm
© Copyright 2004 - 2018 The Fire Company Pty Ltd. All rights reserved. V0318
EcoSmart Fires do not require any form of permanent xture or tting,
such as a ue for ventilation, a permanent connection or any kind of
xed utility for fuel supply.
To ensure adequate ventilation, make sure to follow the guidelines in
the table shown.
Underwriters Laboratories calculates adequate air exchange as
follows:
In a house of typical construction, that is, one that is not of unusually
tight construction due to heavy insulation and tight seals against air
inltration, an adequate supply of air for combustion and ventilation
is provided through inltration. However, if the unvented decorative
appliance is used in a small room where less than 5.7m3[200 cubic
feet] of air space is provided for each 1000 BTU per hour of unvented
decorative appliance rating (considering the maximum burner
adjustment), the door(s) to adjacent room(s) should be kept open or a
window to the outside should be opened at least 25.4mm [1 inch] to
guard against potential buildup of indoor air pollution. Do not use the
appliance in a bathroom or any other small room.
BK5 The room cannot be less than 70m3[2472ft3] .
BK3 The room cannot be less than 45m3[1589ft3] .
BK2UL The room cannot be less than 45m3[1589ft3] .
XL1200 The room cannot be less than 115m3[4061ft3] .
XL900 The room cannot be less than 110m3[3884ft3] .
XL700 The room cannot be less than 90m3[3178ft3] .
XL500 The room cannot be less than 80m3[2825ft3] .
XS340 The room cannot be less than 45m3[1589ft3] .
AB8 The room cannot be less than 116m3[4096ft3] .
AB3 The room cannot be less than 40m3[1413ft3] .
VB2 The room cannot be less than 45m3[1589ft3] .
The ventilation requirements must always be met. The burner must only
be installed in areas that are protected from the draft eects of cross
ventilation.
www.ecosmartre.com e-NRG Bioethanol is the only fuel to use in this appliance.
ENGLISH
The EcoSmart Fire Burners are fuelled by a renewable energy source
called e-NRG Bioethanol.
FLAMMABLE!: Refer to warnings on page 1.
Keep the fuel out of reach of children. Store e-NRG Bioethanol at a
safe distance at all times - a minimum of 1500mm [59.1in] from the
appliance.
Australia
Visit -
Call - 1300 003 NRG
USA
Visit - www.e-NRG.com
Call - (888) 670 ENRG
Or contact your local EcoSmart Fire distributor.
Net (MAX)
Heats
When used indoors.
BK5 5 Litres
[1.3 Gallons]
2 Litres
[0.5 Gallons]
14 MJ/h
13,000 BTU/h
3.5 kW
Over 35m2
[376.7ft2]0.64 L/h [0.17 Gal/h] 7 - 11 hours
BK3 3 Litres
[0.8 Gallons]
1.1 Litres
[0.3 Gallons]
9.04 MJ/h
8,565 BTU/h
2.51 kW
Over 25m2
[269ft2]0.46 L/h [0.12 Gal/h] 6 hours
BK2UL 2 Litres
[0.5 Gallons]
1.1 Litres
[0.3 Gallons]
10.09 MJ/h
9,570 BTU/h
2.8 kW
Over 25m2
[269ft2]0.49 L/h [0.13 Gal/h] 4 hours
XL1200 10 Litres
[2.6 Gallons]
1.5 Litres
[0.4 Gallons]
17 MJ/h
16,200 BTU/h
4.75 kW
Over 65m2
[700ft2]0.87 L/h [0.23 Gal/h] 9 - 14 hours
XL900 9 Litres
[2.4 Gallons]
1.7 Litres
[0.4 Gallons]
16 MJ/h
15,000 BTU/h
4.4 kW
Over 60m2
[645ft2]0.8 L/h [0.21 Gal/h] 8 - 13 hours
XL700 7 Litres
[1.8 Gallons]
1.1 Litres
[0.3 Gallons]
14.5 MJ/h
13,650 BTU/h
4 kW
Over 50m2
[538ft2]0.7 L/h [0.18 Gal/h] 9 - 12 hours
XL500 5 Litres
[1.3 Gallons]
0.7 Litres
[0.2 Gallons]
12 MJ/h
11,430 BTU/h
3.35 kW
Over 40m2
[430.6ft2]0.5 L/h [0.13 Gal/h] 10 - 13 hours
XS340 2.5 Litres
[0.7 Gallons]
0.5 Litres
[0.1 Gallons]
8.93 MJ/h
8,530 BTU/h
2.5 kW
Over 20m2
[215ft2]0.45 L/h [0.12 Gal/h] 5 hours
AB8 8 Litres
[2.1 Gallons]
2.1 Litres
[0.6 Gallons]
21.56 MJ/h
20,433 BTU/h
5.99 kW
Over 60m2
[645ft2]1.1 L/h [0.29 Gal/h] 7- 11 hours
AB3 2.5 Litres
[0.7 Gallons]
0.4 Litres
[0.1 Gallons]
6.14 MJ/h
5,800 BTU/h
1.7 kW
Over 20m2
[215ft2]0.31 L/h [0.1 Gal/h] 8 - 11 hours
VB2 2 Litres
[0.5 Gallons]
0.9 Litres
[0.2 Gallons]
7.24 MJ/h
6,180 BTU/h
2.5 kW
Over 15m2
[161ft2]0.5 L/h [0.13 Gal/h] 6 hours
All EcoSmart Fire Burners have a Thermal Eciency of over 90%.
NOTE: These values are indicative only and may vary depending on the model purchased and installation and the country where the e-NRG
Bioethanol is sourced.
*This gure relates to the area within the appliance where the fuel is intended to be combusted.
© Copyright 2004 - 2018 The Fire Company Pty Ltd. All rights reserved. V0318
e-NRG Bioethanol is the ONLY fuel to be used in this appliance.
To order your e-NRG Fuel contact:
Australia
Visit -
Call - 1300 003 NRG
USA
Visit - www.e-NRG.com
Call - (888) 670 ENRG
Or contact your local EcoSmart Fire distributor.
e-NRG Bioethanol is classied as a Dangerous Goods Flammable Liquid
Class 3, PGII and is regulated by specic standards and rules. You must
familiarise yourself with the appropriate regulations of your country in
order to safely and legally store, handle, decant and use this fuel.
e-NRG Bioethanol containers are recyclable and should be disposed
of accordingly.
To view a video of fuelling your Fire, visit our website at
ecosmartre.com and click on Fire Safety.
Decanting must be performed in a well-ventilated area to ensure that
any spillage is easily contained and away from any ignition source.
INCLUDED WITH THIS
BURNER:
1. Remove the nozzle from your
Jerry Can.
2. Carefully decant the fuel from
the bottle into the Jerry Can
through its opening, avoiding
spillage (you may need to decant multiple bottles depending on the
packaging volume purchased). If spillage occurs, clean thoroughly
before proceeding. (Refer to Troubleshooting on page 20).
3. Re-screw the cap tightly back onto the Jerry Can to contain fuel and
avoid accidental spillage.
4. Test that it is closed securely before moving away from your
decanting area.
5. You are ready to approach the Burner.
B. USING THE e-NRG
FUEL BOTTLE:
1. Remove the cap from the fuel
bottle.
2. Attach the adapter to the fuel
bottle.
WARNING: Fuel containers
without ame arresters, if used
improperly, can result in the
inammation of the fuel within
the container, which may cause
personal injury or property
damage. Never ll the burner
directly from the e-NRG bottle,
risk of explosion.
3. Attach the Spill Proof Safety
Spout to the adapter. Test
that it is closed securely
before moving away from your
decanting area.
4. You are ready to approach the
Burner.
www.ecosmartre.com e-NRG Bioethanol is the only fuel to use in this appliance.
ENGLISH
To view a video of fuelling your Fire, visit our website at
ecosmartre.com and click on Fire Safety.
WAR
WARNING:
WARNING:
WARNING:
As an additional safety measure, we recommend that you remove the
burner and check that there is no unexpected fuel collection in the Top Tray.
The Fire Company Pty Ltd recommends that the quantity of e-NRG
Bioethanol poured into the burner be burnt until empty rather than
extinguishing the re early. Extinguishing the re early can result in a larger
amount of residual fumes in the Burner and a more volatile re-ignition.
When fumes are combined with excess fuel it could be a hazard to
people who are unaware of the Fire operation and its condition of use
(e.g smokers). Ensure only those who have read the instructions attempt
to operate the burner.
AB Series:
To ll the AB Series, position the
Jerry Can spout in the middle of
the burner mouth.
4
4. Re-position the Burner slider
ensuring the grid work of the
burner is visible through the
lling point. This will clear the
lling point for the insertion of
the Jerry Can spout as well
as allowing visual monitoring
of the amount of fuel being
added, according to the volume
markings on the Burner.
5. Once ready, carefully place
the Jerry Can spout inside
the lling point. NEVER ll
over the maximum level as
indicated on the burner vent
inside the Burner and only ll
to the level that you require for
burning time.
6. Use both hands to pour. Place
the palm of one hand on the
top of the nozzle with your
thumb on the green button.
Use your other hand to tip
the can vertically and hold it
steady. Press down on the
green button to release the
fuel. To stop the ow, simply
release the green button.
87
7. When lling is complete, ip
the lid that covers the lling
point so it closes the lling
point.
8. Re-position the slider to the
fully open position. Check
surrounding area for any
spillage. WARNING: Fire
1500m
[59.1in]
9. Make sure that the Jerry Can
is at least 1500mm [59.1in]
away from the replace before
you ignite the re.
2
3
1
1. Remove the transport locking
strip and position the slider
mechanism setting so the
chamber is fully open.
2. Inspect inside the burner
mouth to ensure it is clean and
clear of any foreign particles.
3. Access the lling point by
ipping the small lid which is
located in the bottom right
corner of the burner.
XL Series (Not applicable for
XS340): The XL Series feature
a spring loading cap. It is
engineered so that the Jerry Can
spout is fully enclosed prior to
releasing the fuel supply, thus
allowing lling at a high rate,
whilst eliminating splashing as
the fuel is being decanted.
The XL ame is most visible
when the burner is lled to the
MAX line.
VB2 & XS340
To ll the VB Series, position the
Jerry Can spout in the middle of
the burner mouth.
© Copyright 2004 - 2018 The Fire Company Pty Ltd. All rights reserved. V0318
To view a video of Lighting the Burner, visit our website at
ecosmartre.com and click on Fire Safety.
WARNING:
Before lighting, ensure
that the Burner is clear and ready for use. Open the slider fully and wait
for 60 seconds for the residual fumes to dissipate before lighting.
Check the slider is free from obstruction and operating smoothly.
(Refer to Troubleshooting section on page 20 if diculties are
experienced).
Do not smoke while lighting the Burner, and make sure that no one is
in front of the replace while igniting the Burner. Only use the lighter
supplied with your EcoSmart Fire.
21
3
4
1. Dip the lighting rod tip into the chamber opening “Burner zone” to
wet the end.
2. Lift the lighting rod away from the Burner (do not drip fuel on the oor).
3. Ignite the lighter and make contact with the lighting rod as if lighting
a candle.
4. Dip the ignited lighting rod back into the Burner zone to ignite the
contained fuel.
5. Allow residual ame on lighting rod to burn out.
NOTE: The XL1200, XL900 & XL700 is best ignited from the right hand
side of the ignition zone.
Once lit there will be a residual ame on the lighting rod that must burn
out before putting the rod away. If the ame on the lighting rod dies
before reaching the burner, repeat the procedure until successful.
Due to some residual oil in the bres we use in the Burner there is a
stronger smell when rst operating. It will decrease substantially after
the rst few times you use the Burner, and even more so over time. To
minimise this, wash the burner out in hot water before using. The Burner
must be completely dry and cool before lling with fuel.
Not applicable for BK2UL or BK3 models.
Wait until the re is established (approx 10 minutes) before regulating.
To decrease the ame intensity insert the lighting rod tip through the
circular ring and push forward gently to desired setting. Only use the
lighting rod supplied with your EcoSmart Fire to avoid hand burns.
To increase the ame intensity insert the lighting rod tip through the
circular ring and pull back gently to desired setting. Only use the lighting
rod supplied with your EcoSmart Fire to avoid hand burns.
These eciency devices are a standard inclusion with the XL Series and
AB8 Burners. Baes (or Rings) are placed over the internal burner vents
when cold and not operating and serve to increase the eciency of the
burner as well as further stabilise the ame of the burner. ( XL1200 - 5x
Baes, XL900 - 4x Baes, XL700 - 3x Baes, XL500 - 2x Baes, AB8 -
1x Eciency Ring)
Note: Regulatory function and accessories not applicable to XS340,
BK2UL, VB2 and AB3 – in these models, the control must be in the fully
ON or fully OFF position only. The ame cannot be adjusted.
XL1200 5 x Baes
AB8 1 x Eciency Ring
All Burner parts will age over the course of time through
natural processes associated with use, heat and ame.
Please also note that new stainless steel has an oil coating that will burn
o during the rst few uses. You will notice an accumulation of carbon
around the top opening of the Burner zone and its vents. This will appear
quickly and is normal. You will need to perform your rst maintenance
after approximately 20 litres [5.28 Gal] of e-NRG Bioethanol burnt.
After this, the accumulation will be far slower and maintenance can then
occur every 50 litres [13.20 Gal] of e-NRG Bioethanol burnt. If anything
abnormal appears, do not operate the appliance. If the re is running, turn
it o immediately and contact your distributor before using again.
www.ecosmartre.com e-NRG Bioethanol is the only fuel to use in this appliance.
ENGLISH
To view a video of extinguishing your Fire, visit our website at
ecosmartre.com and click on Fire Safety.
1. Let it burn until the fuel is consumed. The ame will extinguish
when no fuel is left.
2. Use the lighting rod to move the circular ring to the fully OFF
position.
XL Series:
The XL Series have a ip lid shut-o mechanism.
The lid ips across the ignition zone which extinguishes the ame.
A lid is used to extinguish the ame.
WARNING!
e-NRG BIOETHANOL IN THE BURNER.
PERFORMED ABOVE AND BESIDE THE BURNER TO AVOID
DRIPPING THE FUEL AT ANY STAGE OF THE LIGHTING
PROCESS OUT OF THE FIREPLACE ONTO THE FLOOR.
ADDITIONAL e-NRG BIOETHANOL WHEN THE FLAME IS GOING
OR WHEN THE BURNER IS HOT.
e-NRG BIOETHANOL IS THAT
THE FLAME PRODUCED CAN BE NEARLY INVISIBLE IN
NORMAL DAYLIGHT CONDITIONS OR WHEN FIRST LIT. BEING
DIFFICULT TO SEE, AN INEXPERIENCED PERSON CAN EASILY
ASSUME THE BURNER IS EMPTY AND NEEDS FILLING.
ASSUME BURNER IS LIT, EVEN IF YOU DON’T SEE FLAME.
FOLLOW PROCEDURE TO EXTINGUISH FLAME AND ALLOW
UNIT TO COOL BEFORE ATTEMPTING TO REFUEL. NEVER
REFUEL WITH BURNER LIT OR WHILE UNIT IS HOT.
1. Move the slider/hinge so the Burner opening is fully open.
2. Wait 60 minutes before re-igniting the Burner. The Burner should
be at room temperature. Please be aware that if this time is not
respected the ignition could be pressurised and therefore stronger. A
pressurised ignition can cause serious burns if you are close to the
Burner.
3. Re-ignite as described in “Lighting the Burner”.
© Copyright 2004 - 2018 The Fire Company Pty Ltd. All rights reserved. V0318
e-NRG bioethanol is the ONLY fuel suitable for use in this
appliance.
Check your burner is in good working condition, the shut o
mechanism is working smoothly, the lling point is accessible and
eective, nothing foreign has fallen into it and make sure there is
no visual or physical damage to the burner
Frequently inspect all around the installation – including lifting the
burner out of its position to ensure that no fuel has accumulated
in or around the setting at any time
Take out your operations manual and refresh your memory on the
operational procedures for using this product – it’s available on
our website too
Give your burner a good clean, they can be washed out with hot
soapy water and left to dry - or pop it in your dishwasher on the
hot pan cycle with detergent (refer to your Operations Manual)
Check the operation of your Jerry Can, re extinguisher, lighter
and lighting rod to ensure you have the right tools to use for
safely operating your re - replacement accessories are available
from your closest distributor
Check your fuel supply is stored according to regulations – if you
are unsure contact your local distributor
Check that all ammable items are within safe distance from the
ame – that’s a minimum of 1500mm [59.1in] at all times in all
conditions
And remember, never overll your burner, never ll your burner
whilst it is in operation or hot, never leave a re unguarded and
never leave children unsupervised
This manual suits for next models
14
Table of contents
Languages:
Other Eco-Smart Burner manuals
Popular Burner manuals by other brands
Bentone
Bentone BG 950 M Installation and maintenance instruction
Hotsy
Hotsy 9452 Operator's manual
Benjamin Heating products
Benjamin Heating products FS140 owner's manual
Enertech
Enertech Bentone B2S Classic Installation and maintenance instruction
Town & Country Fireplaces
Town & Country Fireplaces TC36.NG02DN installation instructions
baltur
baltur TBG 80 SLX ME Instruction manual for installation, use and maintenance
Riello Burners
Riello Burners RDB 3.2 50/70 Mistral Installation, use and maintenance instructions
Unigas
Unigas TLX115 Installation - use - maintenance
XTline
XTline XT23509 manual
Beckett
Beckett NX manual
Riello
Riello RLS 70/E Installation, use and maintenance instructions
Riello
Riello RDB Installation, use and maintenance instructions
Riello
Riello RDB2.2 FIREBIRD C20 70K DGT Installation, use and maintenance instructions
EOGB
EOGB X500-2 instruction manual
Riello
Riello RG4F Installation, use and maintenance instructions
Riello Burners
Riello Burners 3898530 Installation, use and maintenance instructions
Elster
Elster ECOMAX 0C technical information
Beckett
Beckett 120 Vac/60 Hz instruction manual